1. 서론
This manual provides detailed instructions for the installation, operation, and maintenance of the Wheelock SBB-W Surface Backbox. The SBB-W is designed to provide a surface mounting solution for compatible Wheelock devices, ensuring a secure and aesthetically pleasing installation. Please read this manual thoroughly before attempting any installation or operation.
2. 안전 정보
경고: 설치는 모든 지역 및 국가 전기 규정 및 표준에 따라 자격을 갖춘 인원이 수행해야 합니다.
- 기기를 설치하거나 정비하기 전에 항상 전원을 차단하십시오.
- 모든 연결 부분이 안전하고 적절히 절연되어 있는지 확인하세요.
- Do not expose the backbox to extreme temperatures or moisture beyond its specified operating conditions.
- Use only approved tools and hardware for installation.
3. 패키지 내용
상자를 조심스럽게 풀고 모든 품목이 들어 있고 손상되지 않았는지 확인하세요. 품목이 없거나 손상된 경우 즉시 공급업체에 문의하세요.
- 1 x Wheelock SBB-W Surface Backbox (White)
- Installation Hardware (screws, anchors - may vary)
Figure 1: Wheelock SBB-W White Surface Backbox. This image shows the front view of the white surface backbox, designed for mounting compatible fire safety devices.
4. 설정 및 설치
Follow these steps for proper installation of the SBB-W Surface Backbox:
- 장착 위치 선택: Choose a flat, stable surface suitable for mounting the backbox. Ensure there is sufficient space for the backbox and any connected devices, and that the location complies with all relevant building codes.
- 장착 구멍 표시: Position the backbox against the desired mounting surface. Use a pencil or marker to mark the locations for the mounting screws through the designated holes on the backbox.
- 드릴 파일럿 홀: Using an appropriate drill bit for your mounting surface (e.g., wood, drywall, masonry), drill pilot holes at the marked locations. If mounting into drywall, insert wall anchors as needed.
- Secure Backbox: Align the backbox with the pilot holes and secure it to the surface using the provided mounting screws. Do not overtighten, but ensure the backbox is firmly attached and does not wobble.
- 와이어 관리: Route necessary wiring into the backbox through the designated knockouts or entry points. Ensure all wiring is properly stripped, terminated, and secured according to electrical codes.
- 마운트 장치: Once the backbox is securely installed and wired, mount the compatible Wheelock device (e.g., horn, strobe) onto the backbox according to the device's specific installation instructions.
5. 사용 설명서
The Wheelock SBB-W Surface Backbox is a passive component designed to house and protect compatible Wheelock fire alarm signaling devices. It does not have active operational controls. Its primary function is to provide a secure and compliant mounting enclosure for the device it supports.
Operation of the overall system will depend on the specific signaling device installed within the backbox and the fire alarm control panel to which it is connected. Refer to the instruction manual of the installed device for its operational details.
6. 유지관리
The SBB-W Surface Backbox requires minimal maintenance. Regular inspection is recommended to ensure its integrity and proper function as an enclosure.
- 시각적 검사: Periodically inspect the backbox for any signs of physical damage, cracks, discoloration, or loose mounting.
- 청소: If necessary, clean the exterior of the backbox with a soft, damp 천으로 닦으세요. 연마성 세제나 용제는 마감재를 손상시킬 수 있으므로 사용하지 마세요.
- 안전한 장착: Ensure that the backbox remains securely mounted to the surface. Tighten any loose screws if found.
7. 문제 해결
As a passive enclosure, the SBB-W backbox itself typically does not experience "malfunctions." Most issues will relate to its installation or the device it houses.
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| Backbox is loose on mounting surface. | Screws are not tightened sufficiently or anchors are failing. | Tighten mounting screws. If anchors are failing, replace with appropriate anchors for the wall material. |
| Damage to backbox (cracks, dents). | 물리적 충격이나 부적절한 취급. | Replace the damaged backbox to ensure proper protection of the internal device. |
| Device mounted in backbox is not functioning. | Issue with the device itself or its wiring. | Refer to the troubleshooting section of the specific device's instruction manual. Verify wiring connections. |
8. 사양
| 특징 | 세부 사항 |
|---|---|
| 모델 번호 | SBB-W |
| 부품 번호 | WSBBW |
| 상표 | 휠록 |
| 색상 | 하얀색 |
| 스타일 | 안전 |
| 제조업체 | WHEELOCK |
| 한국어: | 742779298560 |
| 품목 패키지 수량 | 1 |
| 전원 | 배터리 구동 (Note: This specification likely refers to the device intended for the backbox, not the backbox itself.) |
9. 보증 정보
According to product information, there is 보증 없음 provided for the Wheelock SBB-W Surface Backbox. Please consult your point of purchase for their return or exchange policies.
10. 고객 지원
For technical assistance, questions regarding installation, or to report issues, please contact your authorized Wheelock distributor or the manufacturer directly.
제조업체: WHEELOCK
Please have your product model number (SBB-W) and any relevant purchase information ready when contacting support.
