제품 끝view
The microSHIFT R10 Rear Derailleur is designed for 10-speed bicycle drivetrains, offering compatibility with Shimano systems. It features a long cage design, suitable for a wide range of gear ratios. Constructed from aluminum, this derailleur is built for durability and reliable shifting performance.
이미지: 앞면 view of the microSHIFT R10 Rear Derailleur, showcasing its silver aluminum body and black jockey wheels. The microSHIFT logo is visible on the main body.
설정 및 설치
Proper installation is crucial for optimal performance and longevity of your microSHIFT R10 Rear Derailleur. It is recommended that installation be performed by a qualified bicycle mechanic.
필요한 도구:
- 육각 렌치 세트 (일반적으로 장착 볼트용 5mm)
- 케이블 절단기
- 케이블 크림프
- 토크 렌치 (정밀한 설치를 위해 권장)
설치 단계:
- 변속기 장착: Attach the derailleur to the derailleur hanger on your bicycle frame. Ensure the B-tension screw is correctly positioned against the hanger tab. Tighten the mounting bolt to the manufacturer's recommended torque specification.
- 케이블 라우팅: Route the shift cable from your shifter through the frame's cable guides and into the derailleur's cable anchor bolt. Ensure the cable is free of kinks and excessive friction.
- 케이블 고정: Pull the cable taut and secure it under the cable anchor bolt. Do not overtighten. Trim excess cable and install a cable crimp to prevent fraying.
- 제한 나사 조정:
- 상한(H) 나사: Adjust the H-screw to prevent the chain from shifting beyond the smallest cog. The guide pulley should align directly under the smallest cog.
- 하한(L) 나사: Adjust the L-screw to prevent the chain from shifting beyond the largest cog and into the spokes. The guide pulley should align directly under the largest cog.
- B-장력 조정: With the chain on the largest cog and smallest chainring, adjust the B-tension screw to set the gap between the upper guide pulley and the largest cog. A gap of 5-6mm is generally recommended, but refer to specific drivetrain recommendations for optimal performance.
작동 지침
The microSHIFT R10 Rear Derailleur operates by moving the chain across the rear cassette cogs in response to input from your shift lever. This derailleur is designed for smooth and precise 10-speed shifting.
Shifting Procedure:
- Always pedal forward while shifting. Avoid shifting under heavy load.
- To shift to a larger cog (easier gear), actuate the appropriate shift lever. The derailleur will move inward.
- To shift to a smaller cog (harder gear), actuate the appropriate shift lever. The derailleur will move outward.
- Listen for smooth shifts. If shifting is hesitant or noisy, cable tension adjustment may be required.
Cable Tension Adjustment (Fine-Tuning):
Minor adjustments to cable tension can be made using the barrel adjuster located on the derailleur or shifter.
- If shifting to larger cogs is slow or hesitant, turn the barrel adjuster counter-clockwise (out) to increase cable tension.
- If shifting to smaller cogs is slow or hesitant, turn the barrel adjuster clockwise (in) to decrease cable tension.
유지
Regular maintenance extends the life and ensures the performance of your derailleur.
청소:
- Periodically clean the derailleur body, jockey wheels, and cage with a degreaser and brush. Rinse thoroughly and dry.
- Ensure no grit or grime accumulates around the pivots.
매끄럽게 하기:
- Apply a small amount of bicycle-specific lubricant to the pivot points of the derailleur and the jockey wheel bearings.
- 과도한 윤활은 먼지를 끌어들일 수 있으므로 피하십시오.
점검:
- 변속기 행어가 휘어졌는지 정기적으로 점검하십시오. 휘어진 행어는 변속 불량의 원인이 될 수 있습니다.
- Inspect jockey wheels for wear; replace if teeth are excessively worn or damaged.
- Check cable and housing for fraying, kinks, or contamination. Replace as needed.
문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| Slow or hesitant shifting to larger cogs | Insufficient cable tension; dirty/frayed cable or housing | Increase cable tension with barrel adjuster (counter-clockwise); clean or replace cable/housing. |
| Slow or hesitant shifting to smaller cogs | Excessive cable tension; dirty/frayed cable or housing | Decrease cable tension with barrel adjuster (clockwise); clean or replace cable/housing. |
| Chain overshifts past smallest cog | H-limit screw set too far out | Turn H-limit screw clockwise (in) until chain aligns with smallest cog. |
| Chain overshifts past largest cog (into spokes) | L-limit screw set too far out | Turn L-limit screw clockwise (in) until chain aligns with largest cog. |
| Noisy shifting or poor chain wrap | Incorrect B-tension adjustment; bent derailleur hanger | Adjust B-tension screw; inspect and straighten/replace derailleur hanger. |
명세서
| 특징 | 세부 사항 |
|---|---|
| 상표 | 마이크로시프트 |
| 모델 번호 | RD-R47-BK |
| 속도 호환성 | 10단 속도 |
| 케이지 길이 | 롱 케이지 |
| 호환성 | Shimano Compatible |
| 색상 | 검은색 |
| 재료 | 알류미늄 |
| 장착 유형 | 브레이즈온 마운트 |
| 패키지 무게 | 0.27 킬로그램 |
| 항목 패키지 치수 | 6.42 x 4.29 x 2.83 인치 |
보증 및 지원
For warranty information or technical support regarding your microSHIFT R10 Rear Derailleur, please refer to the official microSHIFT web사이트를 방문하거나 고객 서비스에 직접 문의하세요. 보증 청구를 위해 구매 증빙 자료를 보관하세요.
참고: 구체적인 보증 약관은 지역 및 소매업체에 따라 다를 수 있습니다.