백플레이트(모델 11975)가 포함된 Alphacool Eisblock Aurora Acryl GPX-N RTX 3090/3080 Turbo 사용 설명서

1. 서론

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Alphacool Eisblock Aurora Acryl GPX-N RTX 3090/3080 Turbo with Backplate, Model 11975. This high-performance water block is designed to provide efficient liquid cooling for NVIDIA GeForce RTX 3080 and RTX 3090 graphics cards, featuring an acrylic top, nickel-plated copper base, and integrated digital RGB lighting.

The design focuses on enhanced cooling performance by optimizing the water flow and reducing the thickness of the copper block to 5.5 mm. Thermal pads are set at 1 mm thickness to ensure close contact with components. The integrated addressable RGB LEDs illuminate the entire block, providing aesthetic customization.

2. 안전 정보

• 설치나 유지관리를 하기 전에는 항상 컴퓨터의 전원을 분리하세요.
• 손상을 방지하기 위해 구성품을 조심스럽게 다루십시오.
• Ensure all fittings are securely tightened to prevent leaks.
• Use only approved coolants for liquid cooling systems.
• 어린이의 손이 닿지 않는 곳에 보관하세요.
• 어떤 단계에 대해 확신이 없다면 자격을 갖춘 기술자에게 문의하세요.

3. 패키지 내용

설치를 시작하기 전에 모든 구성품이 있는지 확인하십시오.

• Alphacool Eisblock Aurora Acryl GPX-N RTX 3090/3080 Turbo Water Block
• 백플레이트
• 장착 나사 및 와셔
• 써멀 패드 (미리 재단된 제품 또는 시트 형태)
• 열전도 페이스트
• Digital RGB Adapter Cable
• 설치 가이드(본 문서)

4. 설정 및 설치

Careful installation is crucial for optimal performance and to prevent damage. Follow these steps precisely:

1. 그래픽 카드를 준비하세요:
   • Remove the existing cooler and backplate from your RTX 3080 or RTX 3090 graphics card.
   • Clean the GPU die and memory chips thoroughly with isopropyl alcohol to remove all traces of old thermal paste and pads.
2. 열 패드를 적용하세요:
   • Cut the provided thermal pads to the correct sizes as indicated in the diagram (if provided separately) or use the pre-cut pads.
   • Apply the 1 mm thick thermal pads to the memory modules and voltage regulator components on the graphics card PCB. Ensure full coverage and good contact.
3. 열 페이스트 적용:
   • Apply a small amount of thermal paste to the center of the GPU die. A pea-sized dot or a thin line is usually sufficient. The pressure from the water block will spread it evenly.
4. 워터 블록을 설치하세요:
   • Carefully align the water block with the mounting holes on the graphics card.
   • Gently lower the water block onto the GPU, ensuring the thermal paste and pads make proper contact.
   • Secure the water block using the provided screws. Tighten them in a diagonal pattern to ensure even pressure, but do not overtighten.
5. 백플레이트 설치:
   • Apply any necessary thermal pads to the backplate as per instructions (if applicable).
   • Align the backplate with the mounting holes on the rear of the graphics card.
   • Secure the backplate with the remaining screws.
6. 액체 냉각 루프를 연결하세요:
   • Install your chosen fittings into the G1/4" ports on the water block. Ensure they are hand-tightened securely.
   • Connect the water block to your liquid cooling loop using appropriate tubing.
   • Perform a leak test for at least 24 hours with only the pump running and no power to other components.
7. RGB 조명 연결:
   • Connect the digital RGB adapter cable from the water block to a compatible 3-pin 5V addressable RGB header on your motherboard or a dedicated RGB controller.

그림 1: 상단 view of the Alphacool Eisblock Aurora Acryl GPX-N RTX 3090/3080 Turbo Water Block, showcasing the acrylic top and internal flow paths.

Figure 2: The water block illuminated with addressable RGB lighting, highlighting the internal structure and aesthetic design.

5. 사용 설명서

Once installed and leak-tested, the water block operates as part of your custom liquid cooling loop. Ensure your pump is running and coolant is circulating whenever the computer is powered on.

5.1. RGB 조명 제어

The integrated digital RGB LEDs can be controlled via your motherboard's RGB software (e.g., ASUS Aura Sync, MSI Mystic Light, Gigabyte RGB Fusion) or a compatible external RGB controller. Refer to your motherboard or controller manual for specific software instructions to customize lighting effects and colors.

6. 유지관리

• 냉각수 교체: It is recommended to replace the coolant in your loop every 6-12 months to prevent buildup and maintain optimal performance.
• 시스템 플러시: Periodically flush your entire liquid cooling system with distilled water to remove any contaminants before refilling with fresh coolant.
• 시각적 검사: Regularly inspect tubing, fittings, and the water block for any signs of leaks, discoloration, or particulate buildup.
• 청소: If necessary, the exterior of the water block can be gently wiped with a soft, damp 천. 독한 화학 물질을 사용하지 마십시오.

7. 문제 해결

• No Coolant Flow: Check pump power connection and ensure the pump is functioning. Verify there are no kinks in tubing.
• 누출: Immediately shut down the system. Inspect all fittings and connections. Re-tighten any loose fittings. If a component is damaged, replace it.
• 냉각 성능이 좋지 않음:
  • Ensure thermal paste and pads are correctly applied and making good contact.
  • Check for air bubbles trapped in the water block or radiator.
  • Verify pump speed and radiator fan speeds are adequate.
  • Consider if the cooling capacity of your loop is sufficient for your hardware.
• RGB 조명이 작동하지 않음:
  • 메인보드 또는 RGB 컨트롤러와의 연결 상태를 확인하십시오.
  • Ensure the RGB header is enabled in your motherboard's BIOS/UEFI.
  • Verify that the correct RGB software is installed and configured.

8. 사양

그림 3: 하단 view of the water block with the backplate installed, showing the secure mounting.

9. 보증 및 지원

For warranty information and technical support, please refer to the official Alphacool web사이트를 방문하거나 판매점에 문의하세요. 보증 청구를 위해 구매 증빙 자료를 보관하세요.

알파쿨 공식 Web대지: www.alphacool.com