Alphacool Eisblock Aurora Acryl GPX-N RTX 3090/3080 Ti HOF Water Block User Manual

1. 서론

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Alphacool Eisblock Aurora Acryl GPX-N RTX 3090/3080 Ti HOF water block. This high-performance water block is designed to provide superior cooling for NVIDIA GeForce RTX 3090 and RTX 3080 Ti HOF series graphics cards, enhancing stability and performance through efficient liquid cooling. Please read this manual thoroughly before proceeding with installation.

2. 안전 정보

경고: Improper installation or handling of liquid cooling components can lead to system damage, including leaks and electrical shorts. Always exercise caution and follow instructions carefully.

• 설치를 시작하기 전에 컴퓨터 시스템의 전원이 완전히 꺼져 있고 벽면 콘센트에서 플러그가 뽑혀 있는지 확인하십시오.
• 부품을 다루기 전에 접지된 금속 물체를 만져 몸의 정전기를 방전시키십시오.
• Use only distilled water or approved liquid cooling fluids. Do not use tap water.
• Perform a leak test for at least 24 hours before powering on your system.
• 모든 구성품은 어린이의 손이 닿지 않는 곳에 보관하십시오.
• 어떤 단계에 대해 확신이 없다면 자격을 갖춘 기술자에게 문의하세요.

3. 패키지 내용

Please verify that all items are present in your package. If any items are missing or damaged, contact your retailer or Alphacool support immediately.

• Alphacool Eisblock Aurora Acryl GPX-N RTX 3090/3080 Ti HOF Water Block
• Integrated Backplate
• 장착 나사 및 스페이서
• 써멀 패드 (미리 재단된 제품 또는 시트 형태)
• 열전도 페이스트
• RGB Adapter Cable (if applicable)
• 설치 가이드(본 문서)

4. 설정 및 설치

This section outlines the general steps for installing the water block onto your graphics card. Specific steps for disassembling your graphics card may vary by model; refer to your graphics card manufacturer's documentation for detailed disassembly instructions.

4.1 그래픽 카드 준비

1. Carefully remove the stock cooler from your graphics card. This typically involves unscrewing the mounting screws from the GPU die and removing screws securing the shroud and backplate.
2. Thoroughly clean the GPU die and all memory modules (VRAM) and voltage regulator modules (VRM) of any residual thermal paste or thermal pad material using isopropyl alcohol and a lint-free cloth.

4.2 Applying Thermal Materials

1. Apply a small amount of thermal paste to the center of the GPU die. Spread it evenly to a thin layer using a spatula or by allowing the pressure from the water block to spread it.
2. Cut the provided thermal pads to the correct sizes as indicated in the included diagram (if applicable) or as per the Alphacool installation guide for your specific GPU model.
3. Carefully place the thermal pads onto the VRAM and VRM components. Ensure good contact and coverage. The Alphacool Eisblock design utilizes 1mm thick thermal pads for optimal component contact and cooling performance.

4.3 워터 블록 장착

1. Align the Alphacool Eisblock Aurora water block with the mounting holes on your graphics card.
2. Gently lower the water block onto the graphics card, ensuring the GPU die makes contact with the copper base and thermal pads are correctly seated.
3. Secure the water block using the provided mounting screws. Tighten screws in a diagonal pattern to ensure even pressure, but do not overtighten.
4. Connect the digital RGB cable from the water block to a compatible 3-pin 5V addressable RGB header on your motherboard or a dedicated RGB controller.

그림 1: 상단 view of the Alphacool Eisblock Aurora Acryl GPX-N water block, showcasing the clear acrylic top, internal flow paths, and nickel-plated copper base.

Figure 2: The Alphacool Eisblock Aurora water block illuminated with vibrant digital RGB lighting, highlighting the internal coolant channels and beveled edges.

그림 3: 후면 view of the Alphacool Eisblock Aurora water block, showing the integrated black backplate which provides structural support and additional passive cooling.

4.4 Integrating into the Cooling Loop

1. Install appropriate G1/4" fittings (not included) into the inlet and outlet ports of the water block.
2. Connect the water block to your existing or new custom liquid cooling loop using tubing. Ensure all connections are secure and leak-free.
3. Fill your cooling loop with coolant and perform a leak test. It is highly recommended to use an air pressure leak tester before introducing liquid. Once filled, run the pump for at least 24 hours with the system powered off (using a PSU jumper) to check for any leaks. Place paper towels under all connections to easily spot drips.

5. 사용 설명서

Once the water block is successfully installed and the liquid cooling loop has passed a leak test, you can power on your system.

• 초기 시작: Monitor coolant levels and temperatures closely during the first few hours of operation.
• RGB 제어: The integrated digital RGB lighting can be controlled via your motherboard's RGB software (e.g., ASUS Aura Sync, MSI Mystic Light, Gigabyte RGB Fusion) or a dedicated Alphacool RGB controller. Ensure the 3-pin 5V ARGB header is correctly connected.
• 온도 모니터링: Use monitoring software to keep track of your GPU temperatures to ensure optimal cooling performance.

6. 유지관리

Regular maintenance ensures the longevity and optimal performance of your liquid cooling system.

• 냉각수 교체: It is recommended to replace the coolant every 6-12 months, depending on the coolant type and system usage.
• 시스템 플러시: 냉각수를 교체할 때는 전체 냉각 시스템을 증류수 또는 전용 세척액으로 세척하여 쌓인 침전물을 제거하는 것이 좋습니다.
• Block Inspection: Periodically inspect the water block for any signs of corrosion, algae growth, or blockages. If necessary, disassemble and clean the block using appropriate cleaning agents for acrylic and copper.
• 부속품 점검: Ensure all fittings remain tight and leak-free.

7. 문제 해결

이 섹션에서는 일반적으로 발생할 수 있는 문제에 대해 설명합니다.

• 냉각 성능이 좋지 않음:
  • Ensure proper thermal paste application and thermal pad contact.
  • Check for air bubbles trapped in the water block. Tilt the system gently to dislodge them.
  • Verify pump is operating correctly and coolant flow is adequate.
  • Inspect radiators for dust buildup and clean if necessary.
• 누출:
  • 즉시 시스템 전원을 끄십시오.
  • Identify the source of the leak. Tighten fittings or replace O-rings/tubing as needed.
  • Perform another leak test before powering on.
• RGB 조명이 작동하지 않음:
  • Check the connection of the 3-pin 5V ARGB cable to the motherboard or controller.
  • Ensure the RGB header is enabled in your motherboard's BIOS/UEFI.
  • Verify that the correct RGB software is installed and configured.

8. 사양

9. 보증 및 지원

Alphacool products are manufactured to high quality standards. For warranty information, please refer to the terms and conditions provided with your purchase or visit the official Alphacool web대지.

For technical support, troubleshooting assistance, or to inquire about replacement parts, please contact Alphacool customer service through their official web대지:www.alphacool.com