제품 끝view
The Beckett 5270001U is a 12 Volt DC ignitor designed for use with ADC oil burners. This unit provides a constant duty ignition source, delivering a 20KV peak, 30 mA, 14,000 Volt spark with a midpoint grounded configuration. It is commonly found in 12VDC pressure washers from various brands, including Hot and Hotsy, that utilize Beckett ADC oil burners. This ignitor replaces several Beckett models, including 5218301U, 5218301, 51777U, 51776U, S3-33XB-BADC, and Grainger 35U298. It can also serve as a replacement for a Carlin 40900S used on a Beckett ADC Burner.
그림 1: The Beckett 5270001U 12VDC Igniter. This image displays the main igniter unit, which is a black rectangular component with wires extending from it. Also visible are additional wires and a small black mounting bracket, indicating the complete package for installation.
안전 정보
Always disconnect power before installing or servicing the igniter. Improper installation or handling of high-voltage components can result in serious injury or death. Consult a qualified technician if you are unsure about any installation steps. Ensure all connections are secure and insulated to prevent electrical hazards.
설정 및 설치
The Beckett 5270001U igniter is designed for straightforward replacement in compatible systems. Follow these general steps for installation:
- 전원 차단: Before beginning any work, ensure that the power supply to the oil burner or pressure washer is completely disconnected. Verify with a voltmeter.
- Access Old Igniter: Locate and carefully remove the existing igniter from the burner assembly. Note the orientation and wiring connections before removal. Taking photographs can be helpful.
- 배선: Connect the wires of the new Beckett 5270001U igniter to the corresponding terminals. The input voltage is 12VDC. Ensure correct polarity and secure connections. This igniter does ~ 아니다 include an ignitor control board.
- 설치: Securely mount the new igniter in its designated position within the burner assembly. Ensure it is stable and properly aligned.
- 재조립: Reassemble any covers or components that were removed to access the igniter.
- 전원 재연결: Once installation is complete and all connections are verified, restore power to the unit.
메모: Older style igniters may have contained a fifth, white wire. The 5270001U does not utilize this wire.
작동 지침
The Beckett 5270001U igniter operates automatically as part of the oil burner or pressure washer's ignition sequence. Once properly installed and connected to a 12VDC power source, it will generate a high-voltage spark to ignite the fuel when commanded by the system's control board.
- Ensure the fuel supply is adequate and the burner system is primed according to the manufacturer's instructions for the specific appliance.
- Initiate the start sequence of your oil burner or pressure washer. The igniter should produce a consistent spark to facilitate combustion.
- Monitor the system for proper ignition and stable operation.
유지
The Beckett 5270001U igniter is a sealed unit and generally requires minimal maintenance. However, regular inspection of the surrounding components is recommended:
- 배선 검사: Periodically check all electrical connections for tightness and signs of wear or corrosion. Ensure insulation is intact.
- 청결: Keep the area around the igniter clean and free from dust, debris, or oil residue, which can interfere with proper operation or pose a fire hazard.
- Electrode Gap: While the igniter itself is sealed, the electrodes it powers (if external) should be checked for proper gap and cleanliness according to the oil burner's specific maintenance guidelines.
문제 해결
If the oil burner or pressure washer fails to ignite, consider the following troubleshooting steps related to the igniter:
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 스파크 없음 | No 12VDC power to igniter. 배선 연결에 결함이 있습니다. 점화 장치에 결함이 있습니다. | Check power supply to the igniter. 모든 배선 연결을 검사하고 고정하세요. Test igniter for proper output; replace if defective. |
| 약하거나 간헐적인 스파크 | 낮은 입력 볼륨tage. 느슨한 연결. Internal igniter issue. | Verify 12VDC input voltage는 안정적이다. 모든 전기 연결을 조입니다. Replace igniter if problem persists. |
| Burner Fails to Ignite (Igniter sparks) | Fuel supply issue. Air supply issue. Other burner component failure. | Check fuel lines, filter, and pump. Ensure proper air intake. Consult the oil burner's specific manual or a qualified technician. |
문제 해결 단계를 수행해도 문제가 해결되지 않으면 자격을 갖춘 서비스 기술자에게 문의하는 것이 좋습니다.
명세서
| 특징 | 세부 사항 |
|---|---|
| 모델 번호 | 5270001유 |
| 제조업체 | Beckett Corp. |
| 입력 Voltage | 12VDC |
| 입력 전류 | 4.8 AMPS |
| 출력 볼륨tage | 20KV PK |
| 출력 전류 | 30mA |
| Spark Type | 14,000 Volt Spark Midpoint Grounded |
| 듀티 사이클 | 지속적인 의무 |
| 품목 무게 | 1.92파운드 |
| 제품 치수 | 6.83 x 7.77 x 6.83 인치 |
| 품목 패키지 수량 | 1 |
| 필요한 배터리 | 아니요 |
보증 정보
For specific warranty details regarding the Beckett 5270001U igniter, please refer to the documentation provided with your purchase or contact Beckett Corp. directly. Warranty terms typically cover manufacturing defects under normal use conditions.
고객 지원
For technical assistance, replacement parts, or further inquiries, please contact Beckett Corp. customer support. You can typically find contact information on the manufacturer's official web사이트 또는 제품 포장에 표시되어 있습니다.
제조업체: Beckett Corp.
Please have your model number (5270001U) ready when contacting support.
