1. 서론
Welcome to the FLSUN Super Racer SR 3D Printer user manual. This document provides essential information for the safe and efficient operation of your new FDM Delta 3D printer. Please read this manual thoroughly before operating the device to ensure proper setup, usage, and maintenance.
2. 안전 정보
- 항상 환기가 잘 되는 곳에서 프린터를 작동하세요.
- Keep the printer away from flammable materials, children, and pets.
- Do not touch the hot nozzle or heated bed during operation to avoid burns.
- 전원 공급 장치가 올바르게 연결되고 접지되었는지 확인하세요.
- 유지관리나 청소를 하기 전에 프린터의 플러그를 뽑으세요.
- Use only recommended filament types and sizes (1.75mm PLA).
3. 패키지 내용
아래 나열된 모든 품목이 패키지에 포함되어 있는지 확인하세요.
- FLSUN Super Racer (SR) 3D Printer x 1
- Toolkit (Wrench, screwdriver, wire cutters, spatula, Touch Screen Bracket, Heating Rod, Thermistor, Grease, etc.) x 1
- Standby nozzle and Nozzle dredge needle x 1
- PLA Test filament (200g) x 1
- 사용 설명서 x 1
- Materials rack x 1
- SD Card x 1 & Reader x 1
4. 설정 가이드
4.1 포장 풀기 및 배치
Carefully remove all components from the packaging. Place the FLSUN Super Racer on a stable, level surface in a well-ventilated area. Ensure there is enough space around the printer for operation and maintenance.
4.2 초기 조립
The FLSUN Super Racer comes largely pre-assembled. Refer to the included "Use Manual" for detailed steps on attaching the materials rack and any other minor components.
4.3 전원 연결
Connect the power cable to the printer and then to a grounded electrical outlet. Turn on the power switch located on the printer.
4.4 Automatic Bed Leveling
The FLSUN Super Racer features an automatic leveling system. Navigate to the leveling function on the touch screen and initiate the 27-point accurate leveling process. This ensures optimal print bed calibration for successful prints.
4.5 필라멘트 로딩
Place the PLA test filament (1.75mm) onto the materials rack. Feed the filament into the extruder assembly according to the on-screen instructions or the detailed manual. Ensure the hotend is preheated to the appropriate temperature for PLA before loading.
5. 사용 설명서
5.1 First Print
Insert the provided SD card with pre-loaded test models into the printer's SD card slot. Select a model from the touch screen interface and initiate the print. Monitor the first layer to ensure proper adhesion to the print bed.
5.2 고속 인쇄
The FLSUN Super Racer is designed for high-speed printing, reaching speeds up to 200mm/s with 2800+ mm/s² acceleration. This is achieved through its three-axis linkage technology and powerful stepper motors. For optimal high-speed results, ensure your slicing software settings are configured appropriately.
5.3 이력서 인쇄 기능
정전이 발생한 경우tage, the FLSUN Super Racer is equipped with a resume printing function. The printer will automatically save the current print progress and resume from where it left off once power is restored.
5.4 Large Printing Volume
The printer offers a large build volume of Φ260mm (Diameter) x 330mm (Height), allowing for the creation of larger models.
5.5 실ample Prints
The FLSUN Super Racer is capable of producing a wide variety of objects, from functional parts to decorative items.
6. 유지관리
6.1 Print Bed Cleaning
After each print, allow the print bed to cool down. Use the provided spatula to carefully remove the printed object. Clean the coated lattice glass platform with isopropyl alcohol to ensure good adhesion for subsequent prints.
6.2 Nozzle Maintenance
Regularly check the nozzle for clogs or wear. Use the nozzle dredge needle from the toolkit to clear any blockages. Replace the nozzle if it shows signs of significant wear to maintain print quality.
6.3 Linear Rail Guide Care
The high-precision linear rail guides contribute to print accuracy and stability. Periodically apply a small amount of the provided grease to the linear rails to ensure smooth movement and reduce noise.
7. 문제 해결
- 인쇄물이 침대에 붙지 않아요: Ensure the bed is clean and properly leveled. Adjust Z-offset if necessary. Increase bed temperature slightly if using materials like ABS.
- 필라멘트 막힘: Check the nozzle for blockages. Ensure the hotend temperature is appropriate for the filament. Verify the filament path is clear.
- 인쇄 품질 불량: Review slicing settings (layer height, print speed, retraction). Ensure the printer is stable and free from vibrations. Check for worn nozzle or loose belts.
- 프린터 전원이 켜지지 않음: Verify all power connections. Check the power switch.
For further assistance, please refer to the detailed troubleshooting section in the full user manual or contact FLSUN customer support.
8. 사양
| 특징 | 세부 사항 |
|---|---|
| 모델 | FLSUN-SR |
| 인쇄 기술 | FDM(융합 적층 모델링) 델타 |
| 볼륨을 빌드하세요 | Φ260 x 330 mm (Diameter x Height) |
| 최대 인쇄 속도 | 200mm/초 |
| 최대 가속도 | 2800+ mm/s² |
| 필라멘트 직경 | 1.75mm (XNUMXmm) |
| 지원되는 필라멘트 | PLA (and others as specified by manufacturer) |
| 레벨링 시스템 | Automatic (27-point) |
| 인쇄 재개 | Yes (after power outage) |
| 프린트 베드 | Coated Lattice Glass Platform (Removable) |
| 제품 치수 | 15 x 15 x 35 인치(대략) |
| 품목 무게 | 33파운드 |
9. 보증 및 기술 지원
FLSUN provides responsible after-sales service and lifetime technical support for the Super Racer 3D Printer. If you encounter any issues or have questions, please contact FLSUN customer support. They aim to respond within 24 hours.
For specific warranty details, please refer to the warranty card included with your product or visit the official FLSUN web대지.
