제품 끝view
The ECHO CS-3510 is a commercial-grade gas-powered rear handle chain saw designed for various cutting tasks. Its 34.4cc engine provides substantial power, making it suitable for storm clean-up, light firewood cutting, limb trimming, and felling trees up to 28 inches in diameter. The design prioritizes user comfort and productivity with its lighter weight and efficient power delivery.
Image: The ECHO CS-3510 Chain Saw, showcasing its orange and black design with a 16-inch bar.
주요 특징:
- 34.4cc commercial grade gas engine for reliable power.
- Optimized weight for reduced operator fatigue and increased productivity.
- i-30 starter system designed to reduce starting effort by 30%.
- 3-point spring vibration reduction system for enhanced operator comfort during extended use.
- Air injection air cleaner system for improved air filtration and reduced maintenance requirements.
설치 가이드
1. 포장 풀기 및 초기 검사
Carefully remove all components from the packaging. Inspect the chain saw for any signs of damage that may have occurred during shipping. Ensure all parts listed in the packing list are present.
2. Fuel and Oil Mixture Preparation
The ECHO CS-3510 requires a specific fuel mixture. Use fresh, unleaded gasoline with an octane rating of 89 or higher, mixed with a high-quality 2-stroke engine oil at a ratio specified in the separate engine manual (typically 50:1). Always mix fuel in a clean, approved fuel container.
3. 봉 및 체인 설치
- 체인톱을 평평하고 안정적인 표면에 놓으십시오.
- 너트 두 개를 풀어 체인 커버를 제거하십시오.
- Carefully position the chain around the clutch drum and guide bar, ensuring the cutting edges of the chain are facing the correct direction (refer to directional arrows on the chain).
- Slide the guide bar onto the studs, aligning the chain with the groove in the bar.
- 체인 커버를 다시 씌우고 너트를 손으로 조여주세요.
- Adjust chain tension using the tensioning screw. The chain should be snug against the bar but still able to be pulled freely by hand.
- 체인 커버 너트를 완전히 조이세요.
이미지: 측면 view of the ECHO CS-3510 Chain Saw, illustrating the guide bar and chain assembly.
4. Filling Fuel and Chain Oil Tanks
Fill the fuel tank with the prepared fuel mixture. Fill the chain oil tank with high-quality bar and chain lubricant. Do not overfill. Ensure caps are securely tightened.
작동 지침
1. 작업 전 점검
- 체인 장력이 올바른지 확인하십시오.
- 연료와 체인 오일량을 점검하십시오.
- Inspect the chain for sharpness and damage.
- 모든 너트와 볼트가 단단히 조여져 있는지 확인하십시오.
- Confirm the chain brake is disengaged before starting.
2. 엔진 시동 (냉간 시동)
- Place the chain saw on a firm, flat surface.
- 체인 브레이크를 체결하십시오.
- 초크 레버를 FULL CHOKE 위치로 이동합니다.
- 연료가 보일 때까지 프라이머 펌프를 5~7회 누르십시오.
- Pull the starter handle firmly and smoothly until the engine "pops" or attempts to start.
- 초크 레버를 HALF CHOKE 또는 RUN 위치로 옮기세요.
- 엔진이 시동될 때까지 시동 손잡이를 다시 당기십시오.
- 체인 브레이크를 풀고 작동을 시작하기 전에 엔진을 몇 분간 예열하세요.
3. Starting the Engine (Warm Start)
For a warm engine, move the choke lever directly to the RUN position and pull the starter handle until the engine starts.
4. Basic Cutting Techniques
- Always maintain a firm grip with both hands on the handles.
- 안정적인 자세를 위해 발을 어깨너비로 벌리고 서세요.
- 가이드 바 끝으로 절단하지 마십시오. 역류 현상이 발생하지 않습니다.
- Plan your cuts to ensure the wood falls safely and away from you.
- Be aware of pinching hazards when cutting through logs under tension.
5. 엔진 정지
To stop the engine, move the ignition switch to the "OFF" position. Engage the chain brake for safety when not actively cutting.
유지관리 일정
Regular maintenance is crucial for the longevity and safe operation of your ECHO CS-3510 chain saw.
Daily Maintenance (Before Each Use):
- 체인의 날카로움과 장력을 확인하십시오.
- Inspect guide bar for wear and burrs.
- Verify chain oiler is functioning.
- Clean debris from air filter and cooling fins.
- 모든 패스너가 조여졌는지 확인하십시오.
Weekly Maintenance (or Every 10 Operating Hours):
- 공기 필터를 청소하거나 교체하세요.
- Clean spark plug and check gap. Replace if necessary.
- Clean clutch area and chain brake mechanism.
- Inspect fuel filter.
- Rotate guide bar to ensure even wear.
체인 샤프닝:
안전하고 효율적인 절단을 위해서는 날카로운 체인이 필수적입니다. 원형 톱을 사용하여 체인을 정기적으로 날카롭게 하세요. file of the correct diameter (refer to your chain's specifications) and a flat file for depth gauges. Alternatively, have the chain professionally sharpened.
공기 필터 청소:
Remove the air filter cover and carefully remove the air filter. Clean it with warm, soapy water, rinse thoroughly, and allow it to air dry completely before reinstallation. For heavily soiled filters, replacement may be necessary.
문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 엔진이 시동되지 않습니다 | 연료 부족, 초크 위치 오류, 점화 플러그 오염, 연료 필터 막힘. | Add fresh fuel, adjust choke, clean/replace spark plug, replace fuel filter. |
| 엔진 시동은 걸리지만 꺼집니다. | Incorrect fuel mixture, dirty air filter, carburetor issues. | Use correct fuel mixture, clean air filter, consult service center for carburetor. |
| Chain does not cut efficiently | 체인이 둔해졌거나, 체인 장력이 맞지 않거나, 가이드 바가 마모되었습니다. | Sharpen chain, adjust tension, replace guide bar. |
| 과도한 진동 | 부품이 헐거워졌거나, 체인/바가 손상되었거나, 엔진 균형이 맞지 않는 경우. | Check all fasteners, inspect chain/bar for damage, seek professional service. |
기술 사양
| 사양 | 세부 사항 |
|---|---|
| 상표 | 에코 |
| 모델 번호 | CS-3510-16 |
| 전원 | 가솔린 구동 |
| 엔진 배기량 | 34.4cc |
| 마력 | 2.7킬로와트 |
| 체인 길이 | 16 인치 |
| 품목 무게 | 8.16파운드(130.51온스) |
| 제품 크기(L x W x H) | 20인치 길이 x 12인치 너비 x 12인치 높이 |
| 한국어: | 743184021644 |
| 제조업체 | 에코 |
| 첫 번째 이용 가능 | 15년 2020월 XNUMX일 |
보증 및 지원
ECHO products are manufactured to high standards and are backed by a limited warranty. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official ECHO web대지.
For technical assistance, parts, or service, please contact an authorized ECHO service dealer. You can find a dealer near you by visiting the ECHO website or contacting their customer support line.
중요한: Always provide your product model number (CS-3510-16) and serial number when seeking support.
