1. 서론
This manual provides essential instructions for the installation, operation, and maintenance of your Ring Plug-In Adapter (2nd Generation). This adapter is designed to provide continuous power to compatible Ring Battery Doorbells, eliminating the need for frequent battery recharging and enabling 24/7 power and protection without existing doorbell wiring.
2. 안전 정보
Please read and understand all safety instructions before installing and using this product. Failure to follow these instructions may result in electric shock, fire, or other hazards.
- 이 어댑터는 다음과 같이 설계되었습니다. 실내에서만 사용 가능물, 습기 또는 극한 온도에 노출시키지 마십시오.
- Connect the adapter only to standard indoor power outlets (100-240V AC, 50/60Hz).
- The adapter includes built-in short circuit protection. However, ensure proper wiring connections to prevent damage to the device or doorbell.
- Do not attempt to open or modify the adapter. Refer all servicing to qualified personnel.
- 어린이의 손이 닿지 않는 곳에 보관하세요.
3. 패키지 내용
- Ring Plug-In Adapter (2nd Generation)
- 10-foot cable with fork connectors
4. 설정 및 설치
Follow these steps to install your Ring Plug-In Adapter:
- Prepare Your Doorbell: Ensure your compatible Ring Battery Doorbell has its rechargeable Quick Release Battery Pack inserted. The adapter will keep this battery charged.
- 어댑터 케이블을 연결하세요: Locate the two terminal screws on the back of your Ring Doorbell. Connect the fork connectors of the adapter's 10-foot cable to these screws. It does not matter which wire (red or black) connects to which terminal, as long as they do not touch each other. Tighten the screws to secure the connections.
그림 1: 전면 view of the Ring Plug-In Adapter (2nd Generation). This image shows the compact white adapter unit with the Ring logo on the side and the power cable extending from the bottom.
- 케이블 연결: Carefully route the 10-foot cable from your doorbell to a standard indoor power outlet. Ensure the cable is not pinched or damaged, especially if passing through door frames or walls. Use the included clips to secure the cable if needed.
- 전원을 연결하세요: Plug the Ring Plug-In Adapter into a standard indoor electrical outlet.
그림 2: 뒤로 view of the Ring Plug-In Adapter (2nd Generation) with its electrical specifications label. The label details the model number, input/output power, and regulatory marks.
- 연결 확인: Your Ring Doorbell should power on, and the Ring app should indicate a "Hardwired" status in the Device Health section. If the doorbell's light changes to a permanent white color, it indicates a successful power connection.
5. 운영
Once installed, the Ring Plug-In Adapter provides continuous power to your compatible Ring Battery Doorbell. This means your doorbell will remain powered without requiring you to remove the battery for recharging.
The adapter utilizes a trickle charge mechanism. This means it will slowly and continuously recharge the battery. It is normal for the battery percentage in the Ring app to fluctuate or drop slightly (e.g., to 90%) before the adapter initiates a recharge cycle. This behavior is designed to prolong the overall lifespan of your doorbell's battery.
6. 호환성
The Ring Plug-In Adapter (2nd Generation) is compatible with the following Ring Doorbell models:
- 비디오 초인종 유선
- Video Doorbell (1st Generation)
- Video Doorbell (2nd Generation - 2020 Release)
- 비디오 도어벨 2
- 비디오 도어벨 3
- 비디오 Doorbell 3 Plus
- 비디오 도어벨 4
- 배터리 초인종
- 배터리 도어벨 플러스
- 비디오 도어벨 프로
- 비디오 도어벨 프로 2
다음과 호환되지 않습니다 :
- 핍홀 캠
- 비디오 초인종 엘리트
7. 문제 해결
- Doorbell not showing "Hardwired" in app: During the initial setup tutorial, the doorbell might not immediately recognize the hardwired power source. If this occurs, proceed with the setup. Once the doorbell is fully set up, check the "Device Health" section in the Ring app; it should then correctly display "Hardwired."
- 배터리 퍼센트tage dropping: As explained in the Operation section, the adapter uses a trickle charge. It is normal for the battery percentage to drop to around 90% before the adapter recharges it back to full. This is a protective measure for battery longevity.
- No power to doorbell:
- Ensure the adapter is securely plugged into a working indoor outlet.
- Verify that the cable connections to the doorbell terminals are secure and not loose.
- Check for any visible damage to the cable or adapter.
8. 사양
| 모델 | DBA-12PF16-24 |
| 전원 입력 | 100-240V 교류, 50/60Hz, 0.5A |
| 전력 출력 | 24V DC, 0.5A, 12.0W |
| 케이블 길이 | 10피트(약 3미터) |
| 치수(어댑터 유닛) | 2.8cm(7인치) x 2.2cm(5.5인치) x 1.5cm(3.7인치) |
| 보호 | 내장 단락 보호 |
| 환경 | 실내에서만 사용 가능 |
9. 보증 및 지원
For warranty information, technical support, or further assistance, please visit the official Ring support website or contact Ring customer service. Details can typically be found on the Ring website or within your Ring app.
또한 방문할 수 있습니다 아마존에서 반지 판매 추가 제품 정보 및 리소스를 확인하세요.
