소개
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Lepro LE 50ft RGB 5050 LED Strip Lights. Please read this manual thoroughly before installation and use to ensure proper function and safety. Keep this manual for future reference.
안전 지침
- 설치 또는 유지 관리 전에 전원 공급 장치가 분리되어 있는지 확인하십시오.
- 본 제품은 실내용으로만 설계되었습니다. 물이나 높은 습도에 노출시키지 마십시오.
- Do not connect the LED strip to the power supply while it is still coiled on the reel. Unroll the strip completely before powering on to prevent overheating.
- Use only the provided 12V ETL-listed power adapter. Using an incompatible power supply may damage the product and void the warranty.
- Do not bend the LED strip at sharp angles (less than 90 degrees) to avoid damaging the circuit board or LEDs.
- 어린이의 손이 닿지 않는 곳에 보관하세요.
- If any damage is observed on the strip or power adapter, discontinue use immediately and contact customer support.
패키지 내용
Image: The complete package contents including two rolls of LED strip lights, a remote control, a power adapter, and fixing clips with screws.
아래 나열된 모든 품목이 패키지에 포함되어 있는지 확인하세요.
- 2 x 24.6ft (total 50ft) RGB 5050 LED Strip Lights
- 1 x IR Remote Controller (44-key)
- 1 x 12V ETL-listed Power Adapter
- 1 x 제어 상자
- 클립 및 나사 고정
- 사용 설명서 (본 문서)
명세서
| 모델 번호 | 410105-RGB-US |
| 밝은 색상 | RGB(빨간색, 녹색, 파란색) |
| 광원 유형 | 5050 LED |
| 총 길이 | 50 Feet (2 x 24.6ft rolls) |
| 미터당 LED 개수 | 30개의 LED |
| 전원 | Corded Electric, 12V Adapter |
| 왓tage | 36 와트 |
| 컨트롤러 유형 | IR Remote Control (44-key) |
| 실내/실외 사용 | 실내 전용 |
| 재료 | 플라스틱 |
| 제품 치수 | 5.31 x 3.15 x 5.35인치(패키지) |
| 품목 무게 | 14.72 온스 |
설정 및 설치
LED 스트립 조명을 올바르게 설치하려면 다음 단계를 따르십시오.
- 표면 준비:
Before attaching the LED strip, ensure the installation surface is clean, dry, and smooth. Wipe the surface with a clean cloth to remove dust or debris. This ensures optimal adhesion of the 3M adhesive backing.
Image: A hand wiping a wooden surface with a cloth, illustrating the first step of surface preparation.
- 구성 요소 연결:
Connect the 4-pin connector from the LED strip to the control box. Ensure the arrow mark on the strip's connector aligns with the arrow mark on the control box. Then, connect the DC wire from the power adapter to the control box. Finally, plug the power adapter into a standard electrical outlet.
Image: A visual guide demonstrating how to connect the DC wire to the control box and the 4-pin connector to the LED strip, emphasizing arrow alignment.
중요한: Ensure the "arrow" mark on the LED strip connector and the "12V" mark on the control box are on the same side for correct polarity.
Image: Detail of the RGB light strip, highlighting the 10mm 4-pin connector and the strong 3M self-adhesive backing for installation.
- LED 스트립 부착:
Peel off the protective backing from the 3M adhesive on the back of the LED strip. Carefully press the strip onto the prepared surface, applying firm and even pressure along its entire length. For added security, use the included fixing clips and screws at regular intervals, especially around corners or areas with less adhesion.
Image: A hand demonstrating how to peel and attach the LED strip to a surface, showing the adhesive backing.
- 원격 제어 준비:
Before using the remote control, pull out the transparent plastic chip from the battery compartment. This activates the battery.
Image: A close-up showing a hand pulling the transparent plastic chip from the remote control, indicating battery activation.
설치 시연 영상
Video: A demonstration of the Lepro LED Strip Lights in various indoor settings, showcasing color changes and potential applications. This video provides visual examples of how the lights can be installed and used to enhance different environments.
작업
Your LED strip lights are controlled by the included 44-key IR remote control. Point the remote directly at the IR receiver on the control box for optimal response.
이미지: 자세한 view of the 44-key remote control, showing buttons for power, brightness adjustment, RGB color selection, 6 DIY color buttons, and various dynamic modes like Jump, Fade, Quick, Slow, and Auto.
- 전원 켜기/끄기: 를 누르세요 빨간색 전원 버튼 불을 켜거나 끄다.
- 밝기 조정: 사용하세요 위아래 화살표 버튼 (above the R, G, B, W buttons) to increase or decrease brightness.
- 색상 선택: 아무거나 누르세요. 20 color buttons to select a static color.
- DIY 색상:
- 다음 중 하나를 누릅니다. DIY1-DIY6 buttons.
- 사용하세요 RGB up/down arrows to adjust the intensity of Red, Green, and Blue to create your desired custom color.
- Press the same DIY button again to save the custom color.
- 동적 모드:
- JUMP3 / JUMP7: Cycles through 3 or 7 colors with a jump effect.
- FADE3 / FADE7: 3가지 또는 7가지 색상 사이에서 서서히 변합니다.
- QUICK / SLOW: 동적 모드의 속도를 조절합니다.
- 자동 : Cycles through all available dynamic modes.
- 플래시: Flashes through colors.
유지
- 청소: Ensure the power is off and unplugged before cleaning. Gently wipe the LED strip with a dry, soft cloth. Do not use liquid cleaners or abrasive materials.
- 저장: If storing the lights for an extended period, ensure they are clean and dry. Store in a cool, dry place away from direct sunlight.
- 부착: If the adhesive begins to lose its stickiness, you can reinforce the strip with additional fixing clips or a suitable adhesive tape (not included).
문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 표시등이 켜지지 않습니다. |
|
|
| 리모컨이 응답하지 않습니다. |
|
|
| 색상이 잘못되었거나 일관성이 없습니다. |
|
|
| LED strip is falling off the surface. |
|
|
보증 및 지원
Lepro products are designed for quality and reliability. For warranty information, technical support, or any questions regarding your LED strip lights, please contact Lepro customer service through the retailer where the product was purchased or visit the official Lepro web대지.
Please have your model number (410105-RGB-US) and purchase details ready when contacting support.
