1. 서론
This manual provides detailed instructions for the setup, operation, maintenance, and troubleshooting of your JTECH ServerCall Transmitter Paging System. Please read this manual thoroughly before operating the system to ensure proper function and longevity.
2. 패키지 내용
패키지에 모든 품목이 들어 있는지 확인하세요.
- ServerCall Transmitter Unit
- 24 Rugged Pagers
- Multi-Pager Charging Base(s) (quantity may vary based on configuration)
- 송신기용 전원 어댑터
- Power Adapter(s) for Charging Base(s)
- 송신기용 안테나
- 사용 설명서 (본 문서)
Image: A single JTECH rugged pager, displaying the number '2'. These pagers are designed for durability.
Image: A multi-pager charging base with several pagers docked, indicating they are charging.
3. 설정
- 구성 요소 풀기: 포장에서 모든 구성 요소를 조심스럽게 제거합니다.
- Connect Transmitter Antenna: Screw the antenna securely into the designated port on the back of the ServerCall Transmitter unit.
- 송신기 전원 연결: Plug the transmitter's power adapter into the power input port on the transmitter, then plug the adapter into a standard electrical outlet. The transmitter display should illuminate.
- Position Charging Base(s): Place the charging base(s) in a convenient location, ensuring access to electrical outlets.
- Connect Charging Base Power: Plug the charging base power adapter(s) into the charging base(s), then into standard electrical outlets.
- 충전식 호출기: Place all 24 pagers onto the charging base(s). Ensure each pager makes proper contact with the charging pins. The pagers should indicate charging status (e.g., an indicator light). Allow pagers to charge fully before first use (typically 4-6 hours).
Image: The JTECH ServerCall Transmitter unit, showing its display and control buttons.
4. 사용 설명서
4.1. Paging Individual Pagers
- Ensure the desired pager is powered on and within range.
- On the ServerCall Transmitter, locate the numbered button corresponding to the pager you wish to call (e.g., button '1' for pager '1').
- Press the numbered button once. The pager will vibrate, flash, or beep according to its programmed alert mode.
- The transmitter display may show confirmation or the pager number being called.
4.2. Paging Manager Groups
The system includes dedicated buttons for paging manager groups (MGR 91, MGR 92, MGR 93, MGR 94).
- To page a specific manager group, press the corresponding 관리자 button (e.g., MGR 91).
- All pagers assigned to that manager group will receive the alert.
4.3. Paging All Pagers
To page all active pagers simultaneously:
- 를 누르세요 모든 페이지 송신기의 버튼입니다.
- All 24 pagers will receive the alert.
4.4. Cancelling a Page
If a page needs to be cancelled or cleared from the system:
- 를 누르세요 취소 송신기의 버튼입니다.
- The display may show "CANCEL PANEL". Follow on-screen prompts or press 입력하다 to confirm cancellation of active pages.
Image: The ServerCall Transmitter display indicating "CANCEL PANEL", used for clearing active pages.
4.5. Using Menu and Setup Functions
그만큼 메뉴 그리고 설정 buttons provide access to advanced system configurations. Refer to the on-screen prompts for specific settings such as time adjustment, pager programming, or alert modes.
- 누르다 2X MENU for quick access to common menu options.
- 누르다 3X SELECT to cycle through options within a menu.
- 누르다 설정 to enter the system setup menu.
- 사용 입력하다 선택 사항을 확인하기 위해 취소 to exit menus without saving changes.
5. 유지관리
5.1. 청소
- Wipe the transmitter, pagers, and charging base with a soft, damp 옷감.
- 연마성 세척제, 용제 또는 강한 화학 물질을 사용하지 마십시오.
- Ensure all devices are dry before reconnecting to power.
5.2. Battery Care (Pagers)
- Keep pagers charged when not in use to maintain battery health.
- Avoid fully discharging pager batteries frequently.
- If pagers will be stored for an extended period, charge them fully, then store them in a cool, dry place. Recharge periodically (e.g., every 3 months) to prevent deep discharge.
6. 문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| Transmitter display is off. | 전원이나 전원 어댑터에 문제가 없습니다. | Check power adapter connection to transmitter and wall outlet. Ensure outlet is functional. |
| Pager not receiving page. | Out of range, low battery, or pager off. | Move pager closer to transmitter. Place pager on charging base. Ensure pager is powered on. |
| Pager not charging. | Improper placement on base, dirty contacts, or charging base power issue. | Ensure pager is correctly seated on the charging base. Clean charging contacts on both pager and base with a dry cloth. Check charging base power adapter and outlet. |
| Interference or poor range. | Obstructions, other electronic devices, or antenna issue. | Ensure transmitter antenna is securely attached and upright. Relocate transmitter away from large metal objects or other wireless devices. |
7. 사양
- 모델: ServerCall Transmitter Paging System (B085L154BY)
- 제조업체: 제이텍
- Pagers Included: 24 Rugged Pagers
- 전원: AC Power Adapters (included)
- 작동 주파수: (Information not provided, typically in UHF band)
- 범위: (Information not provided, varies by environment)
- 치수: (정보가 제공되지 않았습니다)
- 무게: (정보가 제공되지 않았습니다)
Note: Specific technical specifications such as operating frequency, range, dimensions, and weight are not provided in the product details. For detailed technical specifications, please refer to the official JTECH product page or contact JTECH support.
8. 보증 정보
The JTECH ServerCall Transmitter Paging System is covered by a standard manufacturer's warranty. For specific details regarding warranty duration, coverage, and claims process, please refer to the warranty card included with your product or visit the official JTECH web해당 사이트에서 구매하세요. 보증 서비스를 받으려면 구매 증빙 자료를 보관하십시오.
9. 고객 지원
If you encounter any issues not covered in this manual or require further assistance, please contact JTECH Customer Support:
- Web대지: Visit the JTECH Store on Amazon (일반 정보용)
- For direct technical support, please refer to the contact information provided in your product packaging or on the official JTECH corporate web대지.
