1. 서론
This manual provides essential information for the installation, operation, and maintenance of your HEIMAN Z-Wave Carbon Monoxide Detector. This device is designed to detect carbon monoxide (CO) gas and alert you to its presence, integrating with your Z-Wave smart home system for enhanced safety.
The HEIMAN Z-Wave Carbon Monoxide Detector is a compact, high-quality device, recognized as a Reddot winner in 2017. It operates on the Z-Wave 868.42 MHz frequency, suitable for the Europe version, and is compatible with various Z-Wave gateways such as Zipato, Fibaro, Vera, and SmartThings.
Figure 1: HEIMAN Z-Wave Carbon Monoxide Detector, front view.
2. 중요한 안전 정보
- This device is a carbon monoxide detector and is not designed to detect smoke, fire, or other gases.
- Do not paint the detector. Paint can clog the sensor openings and prevent the unit from functioning properly.
- Do not block the ventilation openings on the detector.
- Test the detector regularly as described in the "Operating" section.
- The detector requires a CR123A battery. Use only recommended battery types.
- 기기를 직접 수리하려고 하지 마십시오. 모든 서비스는 자격을 갖춘 전문가에게 맡기십시오.
- Carbon monoxide is an invisible, odorless, and tasteless gas. This detector is designed to alert you to its presence, but it does not prevent CO from occurring.
3. 설정 및 설치
3.1 배터리 설치
- Twist the base of the detector counter-clockwise to open the battery compartment.
- Insert one CR123A battery into the compartment, ensuring correct polarity (+/-).
- Remove the protective pull tab if present.
- Close the battery compartment by aligning the base and twisting clockwise until it clicks securely.
그림 2: 후면 view of the detector with the battery compartment open, showing the CR123A battery.
Figure 3: Inserting the CR123A battery into the detector.
3.2 검출기 장착
The detector can be mounted on a wall or ceiling. Carbon monoxide is slightly lighter than air and mixes readily with it. For optimal detection, install the detector:
- In or near sleeping areas.
- On every level of your home.
- At least 1.5 meters (5 feet) from fuel-burning appliances.
- Avoid mounting in corners, near windows, doors, or areas with high airflow.
- 적절한 위치를 선택하십시오.
- Use the provided screws and anchors to secure the mounting plate to the wall or ceiling.
- Attach the detector to the mounting plate by aligning it and twisting clockwise until it locks into place.
Figure 4: HEIMAN Z-Wave Carbon Monoxide Detector mounted on a ceiling.
3.3 Z-Wave Network Inclusion/Exclusion
To integrate the detector into your Z-Wave network:
- Z-Wave 게이트웨이를 연결(페어링) 모드로 설정하십시오. 자세한 지침은 게이트웨이 설명서를 참조하십시오.
- Press the Z-Wave button on the detector three times quickly. The detector will send an inclusion request to the gateway.
- Once successfully included, the detector will appear in your gateway's device list.
- To exclude the device, put your Z-Wave gateway into exclusion mode and press the Z-Wave button on the detector three times quickly.
4. 운영
4.1 LED Indicators and Sound Patterns
The detector uses a combination of LED flashes and beeps to indicate its status:
- 예열: Red LED flashes and four beeps.
- 일산화탄소 경보: 녹색 LED가 50초마다 깜박입니다.
- Normal Detection: Single beep every 50 seconds.
- 배터리 부족: 10초마다 두 번의 경고음이 울립니다.
- 부조: Red LED flashes every 10 seconds, with CO alarm and silent.
Note: The text on the battery in Figure 2 provides a summary of these indicators.
4.2 검출기 테스트
It is recommended to test your CO detector weekly to ensure proper operation.
- 몇 초 동안 감지기의 테스트 버튼을 길게 누릅니다.
- The detector will emit a series of loud beeps and the LED will flash, indicating that the alarm and sensor are functioning correctly.
- Release the button. The detector will return to normal operation.
5. 유지관리
5.1 배터리 교체
The detector is powered by one CR123A battery with an estimated lifespan of 3 years. When the battery is low, the detector will emit two beeps every 10 seconds. Replace the battery immediately when this occurs.
- Twist the base of the detector counter-clockwise to open the battery compartment.
- 기존 CR123A 배터리를 제거하세요.
- 새로운 CR123A 배터리를 극성을 확인하여 삽입하십시오.
- Close the battery compartment by twisting clockwise until it clicks securely.
- 배터리 교체 후 탐지기를 테스트하십시오.
5.2 청소
Clean the detector regularly to prevent dust and debris from affecting its performance.
- 부드러운 d를 사용하세요amp cloth to wipe the exterior of the detector.
- 세척제나 용매를 사용하지 마십시오.
- 감지기를 칠하지 마십시오.
- Gently vacuum around the sensor openings with a soft brush attachment to remove dust.
6. 문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| Detector does not respond during test. | Low or dead battery; device malfunction. | 배터리를 교체하십시오. 문제가 지속되면 고객 지원팀에 문의하십시오. |
| Detector beeps twice every 10 seconds. | 배터리가 부족합니다. | CR123A 배터리를 교체하세요. |
| Detector not pairing with Z-Wave gateway. | Gateway not in inclusion mode; device too far from gateway; interference. | Ensure gateway is in inclusion mode. Move detector closer to gateway. Try excluding and re-including. |
| 거짓 경보. | Improper placement (e.g., near cooking fumes, high humidity); sensor contamination. | Relocate the detector. Clean the detector as per maintenance instructions. |
7. 사양
- 상표: 헤이먼
- 모델: B0851P3WTH
- 전원: 1 x CR123A 배터리
- 배터리 수명: 약 3년
- 센서 유형: 전기 화학
- Z파 주파수: 868.42 MHz (Europe Version)
- 호환성: Z-Wave Plus certified gateways (e.g., Zipato, Fibaro, Vera, SmartThings)
- 스타일: 현대의
- 제조업체: 헤이먼
- 한국어: 345932281906
8. 보증 및 지원
For warranty information and technical support, please refer to the official HEIMAN web사이트를 방문하거나 가까운 대리점에 문의하세요. 구매 영수증을 구매 증빙 자료로 보관하세요.
