소개
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Faultless Ball Satin Stainless Steel Entry Knob and Single Cylinder Deadbolt. Please read these instructions carefully before installation and use to ensure proper function and longevity of your lockset.
안전 정보
- 설치 시에는 항상 장갑과 보안경과 같은 적절한 안전 장비를 착용하십시오.
- 사용하기 전에 모든 구성 요소가 단단히 고정되어 있는지 확인하십시오.
- Do not use excessive force when operating the lockset.
- Keep keys in a safe and accessible location, separate from the door.
패키지 내용
패키지에는 다음 항목이 포함되어 있어야 합니다.
- 2 x Keyed Entry Ball Knobs
- 2 x Single Cylinder Deadbolts
- 4 x KW1 Keys
- Adjustable Latches (for both knob and deadbolt)
- 스트라이크 플레이트
- 장착 나사
- 설치 템플릿(포함된 경우)
Image: All components of the Faultless Ball Satin Stainless Steel Entry Knob and Single Cylinder Deadbolt set, including two knobs and two deadbolts with their respective latches and strike plates.
설정 및 설치
필요한 도구:
- Phillips 헤드 스크루 드라이버
- 줄자
- 연필
- Drill (if new door preparation is needed)
- Wood Chisel (if new door preparation is needed)
설치 단계:
- 문 준비: Ensure your door has the correct bore holes (typically 2-1/8 inches for the lock body and 1 inch for the latch) and backset (2-3/8 inches or 2-3/4 inches). Use the provided template if drilling new holes.
- 래치를 설치하십시오: Insert the latch into the edge bore hole of the door. Ensure the bevel of the latch bolt faces the door frame. Secure with two small screws. Adjust the backset if necessary by twisting the latch mechanism.
- Install the Exterior Knob/Deadbolt: Place the exterior portion of the knob/deadbolt through the large bore hole, ensuring the spindle or tailpiece aligns with the latch mechanism.
- Install the Interior Knob/Deadbolt: Position the interior portion of the knob/deadbolt, aligning it with the exterior portion and the latch. Secure with the long mounting screws provided, tightening evenly.
- 스트라이크 플레이트 설치: Mark the position of the latch bolt on the door frame. Chisel out a shallow recess for the strike plate and secure it with screws. Ensure the latch bolt engages smoothly.
- 테스트 작업: Close the door and test the knob and deadbolt with the key from both inside and outside to ensure smooth operation.
작동 지침
Keyed Entry Knob:
- 외부에서 잠그려면: Insert the key and turn it to lock the knob. Remove the key.
- To Unlock from Outside: Insert the key and turn it to unlock the knob.
- 내부에서 잠그려면: Press or turn the button/thumbturn on the interior knob.
- To Unlock from Inside: Turn the interior knob or button/thumbturn.
단일 실린더 데드볼트:
- 외부에서 잠그려면: Insert the key and turn it to extend the deadbolt. Remove the key.
- To Unlock from Outside: Insert the key and turn it to retract the deadbolt.
- 내부에서 잠그려면: Turn the thumbturn on the interior side to extend the deadbolt.
- To Unlock from Inside: Turn the thumbturn on the interior side to retract the deadbolt.
유지
- 청소: Clean the lockset regularly with a soft, damp cloth. Avoid abrasive cleaners or harsh chemicals, as these can damage the satin stainless steel finish.
- 매끄럽게 하기: Periodically apply a small amount of graphite lubricant or a silicone-based spray to the keyway and latch mechanism to ensure smooth operation. Do not use oil-based lubricants as they can attract dirt.
- 나사 조임 정도: Check and tighten all mounting screws periodically to ensure the lockset remains securely attached to the door.
문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 열쇠가 돌아가지 않거나 뻑뻑합니다. | Dirt in keyway, worn key, or misaligned cylinder. | Clean keyway with graphite lubricant. Try a spare key. Check for proper cylinder alignment. |
| Latch bolt does not retract/extend fully. | Misaligned latch, bent components, or debris. | Check latch alignment and screw tightness. Clear any obstructions. Lubricate the latch mechanism. |
| Door does not close properly with lock engaged. | Misaligned strike plate or door frame issues. | 스트라이크 플레이트 위치를 조정하십시오. 문틀에 변형이나 손상이 있는지 검사하십시오. |
| Knob/Deadbolt feels loose. | 장착 나사가 느슨합니다. | 장착 나사를 고르게 조이십시오. 너무 세게 조이지 마십시오. |
명세서
- 제품 유형: Keyed Entry Knob and Single Cylinder Deadbolt
- 모델: B36L1BD
- 재료: 스테인레스 스틸, 금속
- 마치다: 새틴 스테인리스
- 등급: 3 Grade (Residential)
- 문 나눠 : 오른손잡이
- 조절 가능한 백셋: 2-3/8 inches (60mm) or 2-3/4 inches (70mm)
- 문 두께 범위: 1-3/8인치(35mm) ~ 1-3/4인치(44mm)
- 키웨이: KW1
- Keys Included: 4
- 제품 크기: 약 3.3 x 12.4 x 9.8cm(8.4 x 31.5 x 24.9인치)
- 실내/실외 사용: 집 밖의
보증 및 지원
For warranty information, please refer to the documentation provided at the time of purchase or contact the retailer/manufacturer directly. Specific warranty terms may vary.
For technical support or further assistance, please contact the customer service department of your retailer or the manufacturer, Overstock.
