소개
This manual provides detailed instructions for the setup, operation, and maintenance of your Sharkoon RGB LIT 100 PC Case. Please read this manual thoroughly before installation and use to ensure proper functionality and longevity of your product.
Image: The Sharkoon RGB LIT 100 PC Case, showcasing its tempered glass front panel with a reflective circuitry pattern and an illuminated rear fan.
설정 및 설치
Follow these steps for proper installation of your PC components into the Sharkoon RGB LIT 100 case.
1. 사건 준비
Carefully remove the side panels. The tempered glass side panel can be detached by unscrewing the thumbscrews. Ensure you have a clean, spacious work area.
Image: Interior layout of the PC case, illustrating the spacious design for component installation.
2. 마더보드 설치
The RGB LIT 100 supports Mini-ITX, Micro-ATX, and ATX motherboards. Install your motherboard onto the pre-installed standoffs. Secure it with screws.
3. 전원 공급 장치 설치
Install your power supply unit (PSU) into the dedicated tunnel at the bottom of the case. The PSU can have a maximum length of 21.5 cm. Route cables through the provided pass-throughs for optimal cable management.
4. 저장 드라이브 설치
The case can house up to six SSDs. These can be mounted on the power supply tunnel or behind the mainboard tray. The HDD/SSD cage in the tunnel offers space for either two more SSDs or two 3.5-inch hard drives. The cage is removable if more space is needed for PSU cables.
Image: Rear interior of the case, highlighting cable routing channels and mounting locations for storage drives.
5. 그래픽 카드 및 CPU 쿨러 설치
Install your graphics card(s) into the PCIe slots. Graphics cards with a length of up to 35 cm are supported. CPU coolers with a height of up to 15.7 cm can be accommodated.
6. Fan and Cooling System
The case comes with a pre-installed 120 mm fan behind the front panel for intake and another 120 mm addressable RGB fan at the rear for exhaust. The case supports a total of six fan mounting options and has space for radiators.
Image: Rear exterior of the case, detailing the exhaust fan and expansion slot layout.
Operating the RGB Lighting
The Sharkoon RGB LIT 100 features addressable RGB lighting on the rear fan, an LED strip below the tempered glass side window, and an LED strip in the front panel. The front panel also has a reflective circuitry-like pattern that enhances the lighting effects.
이미지: 앞면 view PC 케이스의 경우,asing the unique RGB lighting pattern on the tempered glass panel.
제어 옵션:
- 케이스 버튼: If your motherboard does not have RGB control, you can cycle through various lighting modes and colors using the reset button on the case.
- 메인보드 소프트웨어: For advanced control and synchronization with other components, connect the case's RGB cables to a compatible addressable RGB header on your motherboard and use the motherboard's dedicated software.
유지
정기적인 유지 관리는 PC 케이스와 구성 요소의 최적 성능과 수명 연장을 보장합니다.
- 먼지 필터: The case includes dust filters behind each air intake. Regularly remove and clean these filters to maintain good airflow and prevent dust buildup inside the case.
- 외부 청소: 부드러운 d를 사용하세요amp cloth to clean the exterior surfaces, including the tempered glass panels. Avoid abrasive cleaners or solvents.
- 내부 청소 : 주기적으로 압축 공기를 사용하여 내부 부품과 팬 날개의 먼지를 제거하십시오. 청소하기 전에 시스템 전원을 끄고 플러그를 뽑으십시오.
문제 해결
이 섹션에서는 일반적으로 발생할 수 있는 문제에 대해 설명합니다.
- 팬이 회전하지 않음:
Ensure all fan power cables are securely connected to the motherboard or a fan controller. Check BIOS settings to confirm fan control is enabled and configured correctly.
- RGB 조명이 작동하지 않음:
Verify that the RGB cables are correctly connected to either the case's internal controller or the motherboard's addressable RGB header. If using motherboard control, ensure the software is installed and configured. Try cycling through modes using the case's reset button if motherboard control is not active.
- 공기 흐름 불량/과열:
Check if dust filters are clean and not obstructed. Ensure fans are oriented correctly for optimal airflow (front intake, rear exhaust). Verify that all case fans are spinning. Consider adding additional fans if temperatures remain high.
- Front Panel USB Ports Not Functioning:
Confirm that the USB 3.0 header cable from the front panel is securely connected to the corresponding header on your motherboard.
명세서
| 특징 | 세부 사항 |
|---|---|
| 모델명 | RGB 조명 100 |
| 케이스 유형 | 미디 타워 |
| 마더보드 호환성 | 미니-ITX, 마이크로-ATX, ATX |
| 치수(길이x너비x높이) | 17.17 x 8.11 x 18.94인치(43.6 x 20.6 x 48.1cm) |
| 품목 무게 | 14.74파운드(6.69kg) |
| 재료 | 강철, 강화 유리 |
| 색상 | 검은색 |
| USB 3.0 포트 | 2 |
| 냉각 방식 | 공기 |
| 사전 설치된 팬 | 1x 120mm front, 1x 120mm addressable RGB rear |
| 최대 그래픽 카드 길이 | 35cm |
| 최대 CPU 쿨러 높이 | 15.7cm |
| 최대 PSU 길이 | 21.5cm |
| 드라이브 베이 | Up to 6x 2.5" SSDs, or 2x 3.5" HDDs + 4x 2.5" SSDs |
보증 및 지원
보증 정보 및 기술 지원에 대해서는 Sharkoon 공식 웹사이트를 참조하십시오. web사이트를 방문하거나 고객 서비스에 직접 문의하세요. 보증 청구를 위해 구매 증빙 자료를 보관하세요.
공식적인 Web대지: www.sharkoon.com
