소개
This user manual provides comprehensive instructions for the Zerone External S Meter SWR Power Meter, designed specifically for use with Yae FT-857D and FT-897 transceivers. This high-performance meter offers excellent durability and stability, clearly displaying critical parameters such as automatic level control voltage, modulation level, standing wave ratio, and supply voltage.
- Only applicable for Yae FT-857D and FT-897.
- Clearly displays the automatic level control voltage, modulation level, standing ratio, and supply voltage.
- High performance and super stability.
- 작동하기 쉽습니다.
- High quality and excellent durability.
설정 및 교정
Receive Display Settings
To configure the meter for receive display:
- 를 누르세요 (기능) key to enter the setup menu and enable the extended menu.
- 회전하다 (선택하다) to call up setup menu item No-061 (MTR ARX SEL).
- 회전하다 (DIAL) to select an external instrument display option from the following:
- -시그
- -CTR
- -VLT
- -N / A
- -FS: Buckle in the instrument 1mA full scale output calibration standard external instruments.
- -끄다
- 누르다 (기능) to save the settings and exit the setup menu.
Emission Display Settings
To configure the meter for emission display:
- 를 누르세요 (기능) key to enter the setup menu and enable the extended menu.
- 회전하다 (선택하다) to call up setup menu item No-061 (MTR ARX SEL).
- 회전하다 (DIAL) to select an external instrument display option from the following:
- -전력
- -ALC
- -모드
- -SWR
- -VLT
- -N / A
- -끄다
교정 방법
To calibrate the meter for accurate readings:
- 를 누르세요 (기능) key to enter the setup menu and enable the extended menu.
- 회전하다 (선택하다) to call up setup menu item No-060 (MTR ARX SEL).
- 회전하다 (DIAL) 선택하다 FS.
- Using a small flathead screwdriver, adjust the calibration adjustment hole at the rear of the unit until the meter pointer reaches full scale.
- 보정이 완료되었습니다.
Figure 1: The Zerone External S Meter with its connecting cable.
그림 2: 자세한 view of the meter's display face, showing SIG, PWR, SWR, MOD, VOLT, and DISC scales.
미터 작동
Once properly set up and calibrated, the Zerone External S Meter provides real-time readings for various radio parameters. The meter's needle will indicate values on the selected scale (SIG, PWR, SWR, MOD, VOLT, DISC) based on your radio's operation mode (receive or transmit).
Refer to your Yaesu FT-857D or FT-897 transceiver's manual for specific interpretations of these readings in different operating scenarios.
Figure 3: The meter clearly displays automatic level control voltage, modulation level, standing wave ratio, and supply voltage.
유지
The Zerone External S Meter is designed for durability. Regular maintenance is minimal but important for continued accuracy and longevity.
- Keep the meter clean and free from dust. Use a soft, dry cloth to wipe the casing and display face.
- 계량기를 극한 온도나 직사광선에 장시간 노출시키지 마십시오.
- If the meter's pointer does not return to zero when the unit is off or disconnected, it may be due to transit bumps. In such cases, carefully adjust the self-zeroing screw located on the mask-side of the instrument. This screw is typically black.
Figure 4: Dimensions of the Zerone External S Meter: 6.7 cm * 7 cm * 6 cm.
문제 해결
This section addresses common issues you might encounter with your Zerone External S Meter.
Hidden Menu Access
If you are unable to find menu items No-060 or No-061 in your radio's setup menu, these menus might be hidden. To access them:
- 길게 누르세요 F key on your radio to open the menu settings.
- Set the relevant menu option to ON to reveal the hidden menus.
- 를 누르세요 F key again to exit and save the settings.
Static Pointer / Zeroing Issues
The instrument is calibrated at delivery. However, transit bumps can sometimes cause the pointer to not rest at zero. If this occurs:
- Locate the black self-zeroing screw on the mask-side of the instrument.
- Gently adjust this screw with a small flathead screwdriver until the pointer rests at the zero mark.
명세서
| 특징 | 세부 사항 |
|---|---|
| 상표 | 제론 |
| 모델 번호 | Zer onekda4y0nmoz |
| 호환되는 라디오 | Yaesu FT-857D, FT-897 |
| 품목 무게 | 10.2온스(0.29킬로그램) |
| 화면 크기 | 3.5 인치 |
| 원산지 | 중국 |
| 한국어: | 745781109282 |
| 첫 번째 이용 가능 | 12년 2019월 XNUMX일 |
보증 정보
Specific warranty details for the Zerone External S Meter are not provided in this manual. Please refer to the product packaging or contact Zerone customer support for information regarding warranty coverage and terms.
고객 지원
For technical assistance, troubleshooting, or general inquiries about your Zerone External S Meter, please visit the official Zerone store or contact their customer service department. Contact information can typically be found on the product packaging or the manufacturer's official web대지.
또한 방문할 수 있습니다 Zerone Store on Amazon 자세한 제품 정보와 지원 리소스를 확인하세요.
