소개
This manual provides detailed instructions for the installation, operation, and maintenance of the Kicker 46KISLOC2 K-Series Stereo Line-Output Converter. Please read this manual thoroughly before installation and use to ensure proper functionality and safety.
The Kicker 46KISLOC2 is designed to integrate aftermarket amplifiers with factory car audio systems by converting speaker-level signals into high-quality RCA line-level signals. It also provides a remote turn-on output for amp정수기.
주요 특징
- Converts speaker-level signals to RCA line-level signals.
- Provides a powerful 100 milli-amp, 12-volt remote turn-on output using DC offset, eliminating the need for a separate switched 12V source.
- Accepts input signals up to 55 watts (16 volts).
- Delivers an output signal up to 8 volts.
- Maintains a flat 20Hz-20kHz frequency response at all volume levels.
- Compatible with standard radios and most smart radios (amplifier output of smart radio must have 60Ω impedance or lower).
- Features an LED indicator for DC offset turn-on.
패키지 내용
패키지에 모든 품목이 들어 있는지 확인하세요.
- Kicker 46KISLOC2 Line-Output Converter unit
- 사용 설명서 (본 문서)
안전 정보
경고:
- 전기 작업을 수행하기 전에 항상 차량의 배터리를 분리하세요.
- Ensure proper wiring and connections to prevent short circuits or damage to the unit or vehicle's electrical system.
- 설치 단계에 대해 잘 모르는 경우 전문 자동차 오디오 설치자에게 문의하세요.
- 본 제품을 습기나 극한의 온도에 노출시키지 마십시오.
설정 및 설치
The KISLOC2 is designed for straightforward installation. Follow these steps carefully:
배선도
Refer to the diagram below for proper wiring connections. The KISLOC2 features input wires for speaker signals and output RCA jacks for line-level signals, plus a remote turn-on wire.
Image: Detailed wiring diagram for the Kicker 46KISLOC2, showing input wires (White: L+, White/BLK: L-, Grey: R+, Grey/BLK: R-, Black: Chassis Gnd) and output connections (Blue: 12V Remote out (100mA), RCAx2: Line level out). A red LED indicates DC offset turn-on activity.
연결 단계
- 스피커 선을 확인하세요: Locate the speaker wires from your factory radio or amplifier that you intend to use as input for the KISLOC2. Typically, these are the rear speaker wires for subwoofer applications or full-range speakers for multi-channel amp리파이어 설정.
- 입력선을 연결하세요:
- 연결하다 하얀색 wire to the Left (+) speaker wire.
- 연결하다 흰색/검정색 wire to the Left (-) speaker wire.
- 연결하다 회색 wire to the Right (+) speaker wire.
- 연결하다 회색/검정색 wire to the Right (-) speaker wire.
- 연결하다 검은색 wire to a reliable chassis ground point in the vehicle.
- RCA 출력 연결: Plug your RCA cables from the KISLOC2's RCA output jacks into the RCA input jacks of your aftermarket amp리퍼.
- 원격 전원 켜기 연결: 연결하다 파란색 wire from the KISLOC2 to the remote turn-on input of your aftermarket amplifier(s). This wire provides a 12V signal to turn on the amplifier when the factory radio is active.
- 장치 보안: Mount the KISLOC2 in a secure, dry location away from excessive heat or moisture. Ensure wires are not pinched or exposed to sharp edges.
이미지: 앞면 view of the Kicker 46KISLOC2 Line-Output Converter, showing the main unit with multiple colored wires extending from one end and two RCA output jacks on the other end. The KICKER logo is visible on the top surface.
이미지: 각도 view of the Kicker 46KISLOC2 Line-Output Converter, showcasing the compact black housing, the array of input wires, and the dual RCA output ports. The KICKER branding is visible on the top surface.
작업
Once properly installed, the KISLOC2 operates automatically. It senses the audio signal from your factory radio and converts it to a line-level signal for your amplifier. The integrated DC offset detection activates the remote turn-on output.
- 전원 켜기: When your factory radio is turned on, the KISLOC2 will detect the DC offset in the speaker signal and activate its remote turn-on output (blue wire), signaling your amplifier to turn on. A red LED on the unit will illuminate to indicate active DC offset turn-on.
- 오디오 출력: The converted line-level audio signal will be sent through the RCA outputs to your amp리퍼.
- 전원 끄기 : When the factory radio is turned off, the KISLOC2 will cease to detect the DC offset, and the remote turn-on output will deactivate, turning off your amp리퍼.
유지
The Kicker 46KISLOC2 is designed for maintenance-free operation. No user-serviceable parts are inside. To ensure longevity:
- 장치를 깨끗하고 먼지나 이물질이 없는 상태로 유지하십시오.
- 모든 배선 연결이 안전하게 유지되고 부식되지 않았는지 확인하세요.
- 본 제품을 극한의 온도나 직사광선에 노출시키지 마십시오.
문제 해결
If you experience issues with your KISLOC2, refer to the following common problems and solutions:
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| Amp리퍼가 켜지지 않습니다. | No signal from factory radio; faulty remote wire connection; factory radio not compatible with DC offset turn-on. | Ensure factory radio is on and playing audio. Check blue remote wire connection. Verify factory radio's amplifier output impedance is 60Ω or lower. If not, a separate switched 12V source for the amplifier's remote input may be required. |
| No audio output from amp리퍼. | Incorrect speaker wire input connections; faulty RCA cables; amp앰프 설정이 잘못되었습니다. | Double-check all input speaker wire connections (polarity). Test RCA cables. Verify amplifier input settings (e.g., input sensitivity, gain). |
| 왜곡된 오디오. | 입력 신호가 너무 높습니다. amp리파이어 게인이 너무 높게 설정되었습니다. | Reduce the volume level of the factory radio. Adjust the gain settings on your aftermarket amp리퍼. |
| Unit gets hot or smokes. | 과부하 또는 단락. | Immediately disconnect power. This indicates a serious issue. Do not re-connect power. Contact Kicker support or a qualified technician. |
명세서
| 특징 | 사양 |
|---|---|
| 모델 | 46KISLOC2 |
| 입력 채널 | 2(스테레오) |
| 최대 입력 신호 | 55 Watts (16 Volts) |
| 출력 볼륨tage | 최대 8볼트 |
| 주파수 응답 | 20Hz - 20kHz (Flat) |
| 원격 켜기 출력 | 100mA, 12V (DC Offset Activated) |
| 치수(L x W) | 6"L x 5"W (approximate, unit body is compact) |
| 무게 | 2.82 온스 |
보증 정보
Kicker products are warranted against defects in material and workmanship for a period of one (1) year from the date of original purchase. Please retain your sales receipt as proof of purchase. This warranty is valid only for the original purchaser and is not transferable.
The warranty does not cover damage due to improper installation, accident, misuse, abuse, negligence, normal wear and tear, or unauthorized modification. For full warranty terms and conditions, please refer to the official Kicker website or contact Kicker customer support.
고객 지원
For technical assistance, troubleshooting, or warranty inquiries, please contact Kicker customer support:
- Web대지: www.kicker.com
- 핸드폰: Refer to the Kicker web지역 연락처 사이트.
- 이메일: Refer to the Kicker web고객 지원 이메일 주소 사이트입니다.
When contacting support, please have your product model number (46KISLOC2) and proof of purchase ready.
