1. 서론
The Onyx KX80 is a compact and versatile 80W AC/DC multi-chemistry battery charger and discharger. Designed for hobbyists, it supports a wide range of battery types including LiPo, LiHV, Li-Ion, LiFe, NiCd, NiMH, and Pb. This manual provides essential information for the safe and efficient operation, setup, and maintenance of your KX80 charger.
2. 안전수칙
- 충전기는 항상 환기가 잘 되는 곳에서, 인화성 물질로부터 멀리 떨어진 곳에서 작동하십시오.
- 충전기를 사용하는 동안에는 절대로 자리를 비우지 마십시오.
- Ensure correct battery type and cell count settings before initiating any charge or discharge cycle. Incorrect settings can lead to battery damage, fire, or injury.
- 손상되거나 부풀어 오른 배터리는 충전하지 마세요.
- 충전기를 습기, 먼지 및 직사광선으로부터 멀리하십시오.
- Use only the provided or approved power cables and adapters.
- 이 제품은 장난감이 아닙니다. 어린이의 손이 닿지 않는 곳에 보관하세요.
3. 패키지 내용
패키지에 모든 품목이 들어 있는지 확인하세요.
- Onyx KX80 80W AC/DC Charger
- AC 전원 코드
- DC Input Cable (Alligator Clips)
- Banana Plug to Deans Adapter
- JST-XH Balance Adapter Board
Image: The Onyx KX80 charger displayed with its complete set of included accessories, including power cables, charging leads, and a balance adapter board.
4. 제품 오버view
The Onyx KX80 features a user-friendly interface with a 2-line LCD screen and four control buttons for easy navigation and operation.
이미지: 각도가 있는 view of the Onyx KX80 charger, showcasin컴팩트한 디자인과 전면 패널 제어 기능을 갖추고 있습니다.
Front Panel Controls and Display:
Image: A close-up of the charger's front panel, highlighting the LCD screen displaying 'LiPo BALANCE CHG' and the four control buttons: Stop, BATT/PROG, Status/Decrease, and Start/Enter.
- LCD 화면: Displays charging parameters, battery status, and menu options.
- 중지 버튼 : Terminates the current operation or returns to the previous menu.
- BATT/PROG Button: Enters the battery program selection menu.
- Status / Decrease Button (Left Arrow): Navigates through menu options or decreases values.
- Start / Enter Button (Right Arrow): Confirms selections or starts operations.
사이드 패널 :
Image: The side of the charger featuring the AC power input port and the DC power input port, labeled 'DC POWER'.
- AC 전원 입력: For connecting the charger to a standard wall outlet (100-240V AC).
- DC 전원 입력: For connecting the charger to a DC power source (11-18V DC), such as a car battery.
Image: The opposite side of the charger, showing the main output terminals (red and black banana plug ports) and the multi-pin balance port for LiPo/LiHV/Li-Ion/LiFe batteries.
- 출력 단자: Red (+) and Black (-) banana plug ports for connecting the main charging lead to the battery.
- 밸런스 포트: Multi-pin port for connecting the balance lead of LiPo, LiHV, Li-Ion, or LiFe batteries (1-6 cells).
5. 설정
5.1 전원 연결
- AC 전원: Connect the AC power cord to the charger's AC input port, then plug the other end into a standard wall outlet (100-240V AC).
- DC 전원 : Alternatively, connect the DC input cable (with alligator clips) to the charger's DC input port. Connect the red clip to the positive (+) terminal and the black clip to the negative (-) terminal of a 11-18V DC power source (e.g., a 12V car battery).
The charger will power on, and the LCD screen will illuminate.
5.2 배터리 연결
- Connect the appropriate charging lead (e.g., Banana plug to Deans adapter) to the charger's main output terminals (red to red, black to black).
- Connect the other end of the charging lead to your battery's main power connector.
- For LiPo, LiHV, Li-Ion, or LiFe batteries, also connect the battery's balance lead to the appropriate slot on the JST-XH balance adapter board, then connect the adapter board to the charger's balance port. Ensure the correct cell count slot is used.
6. 사용 설명서
6.1 메뉴 탐색
사용하세요 배트/프로그 button to cycle through the main battery program types. Use the Status / Decrease 그리고 Start / Enter buttons to navigate within menus and adjust values. Press Start / Enter to confirm a selection or start an operation. Press 멈추다 to go back or end an operation.
6.2 Charging LiPo/LiHV/Li-Ion/LiFe Batteries
- Connect the battery as described in Section 5.2.
- 누르다 배트/프로그 until the desired battery type (e.g., 'LiPo BATT') is displayed.
- 누르다 Start / Enter to enter the LiPo program menu.
- Select the desired mode (e.g., 'LiPo BALANCE CHG' for balanced charging, 'LiPo CHARGE' for fast charging, 'LiPo FAST CHG' for fast charging, 'LiPo STORAGE' for storage charge). Balanced charging is recommended for optimal battery life and safety.
- Adjust the charge current (e.g., 0.1A - 6.0A) using the Status / Decrease 그리고 Start / Enter buttons. A common guideline is to charge at 1C (e.g., for a 5000mAh battery, charge at 5.0A).
- Adjust the cell count (e.g., '3S' for a 3-cell battery). The charger will automatically detect the cell count if connected correctly via the balance port.
- 누르고 있으세요 Start / Enter for 3 seconds to confirm settings and begin the charging process. The charger will perform a cell count check. Confirm by pressing Start / Enter 다시.
- The display will show real-time charging information.
- Once charging is complete, the charger will beep, and the display will indicate 'FULL'. Press 멈추다 and disconnect the battery.
6.3 Charging NiCd/NiMH Batteries
- Connect the battery's main power connector to the charger's output terminals. Balance connection is not required for NiCd/NiMH.
- 누르다 배트/프로그 until 'NiMH BATT' or 'NiCd BATT' is displayed.
- 누르다 Start / Enter 프로그램 메뉴에 들어가려면.
- Select 'NiMH CHARGE' or 'NiCd CHARGE'.
- Adjust the charge current and cell count (if applicable).
- 누르고 있으세요 Start / Enter for 3 seconds to begin charging.
- Disconnect the battery when charging is complete.
6.4 Charging Pb (Lead-Acid) Batteries
- Connect the battery's main power connector to the charger's output terminals.
- 누르다 배트/프로그 until 'Pb BATT' is displayed.
- 누르다 Start / Enter 프로그램 메뉴에 들어가려면.
- Select 'Pb CHARGE'.
- Adjust the charge current and voltag예: 2V, 6V, 12V.
- 누르고 있으세요 Start / Enter for 3 seconds to begin charging.
- Disconnect the battery when charging is complete.
6.5 Discharging Batteries
The KX80 offers a discharge function (2A, 10W). This is useful for cycling NiCd/NiMH batteries or preparing LiPo/LiHV/Li-Ion/LiFe batteries for storage.
- 배터리를 연결합니다.
- Navigate to the desired battery type program.
- Select the 'DISCHARGE' mode.
- Adjust the discharge current and final voltage(해당하는 경우).
- 누르고 있으세요 Start / Enter for 3 seconds to begin discharging.
- The charger will stop automatically when the set parameters are reached.
7. 유지관리
- 충전기를 깨끗하고 먼지가 없는 상태로 유지하세요. 청소 시에는 부드럽고 마른 천을 사용하세요.
- 용제나 연마제를 사용하지 마십시오.
- Regularly inspect all cables and connectors for damage. Replace any damaged components immediately.
- 사용하지 않을 때에는 충전기를 서늘하고 건조한 곳에 보관하십시오.
8. 문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 충전기의 전원이 켜지지 않습니다. | No power supply; faulty cable; incorrect DC input polarity. | Check AC/DC power connections; ensure correct DC polarity; try a different power outlet/source. |
| Error message 'INPUT VOLTAGE ERROR'. | 입력 볼륨tage가 너무 낮거나 너무 높습니다. | Ensure DC input is between 11-18V. If using AC, ensure stable power supply. |
| Error message 'CELL COUNT ERROR'. | Incorrect cell count setting or balance lead connection issue. | Verify battery cell count matches charger setting; ensure balance lead is correctly connected to the balance port. |
| Error message 'CONNECTION BREAK'. | Battery not connected or connection is loose. | 배터리 연결부(메인 리드 및 밸런스 리드)를 모두 확인하십시오. |
| 충전기는 작동 중에 뜨거워집니다. | 정상 작동 중, 환기가 잘 안 됨. | Ensure adequate airflow around the charger. If excessively hot, reduce charge current. |
9. 사양
| 특징 | 사양 |
|---|---|
| 입력 Voltage | AC 100-240V (50/60Hz) or DC 11-18V |
| 충전 전력 | 80와트 |
| 방전 전력 | 10와트 |
| 충전 전류 범위 | 0.1 - 6.0A |
| 방전 전류 범위 | 0.1 - 2.0A |
| LiPo/LiHV/Li-Ion/LiFe Cell Count | 1-6S |
| NiCd/NiMH Cell Count | 1-15 셀 |
| Pb 배터리 볼륨tage | 2-20V |
| 균형 전류 | 300mA/셀 |
| 치수 | 8.1 x 6.7 x 3 인치 |
| 무게 | 1.59파운드 |
10. 보증 및 지원
For warranty information and technical support, please refer to the official Onyx product web웹사이트를 방문하거나 공인 대리점에 문의하세요. 구매 증빙 자료로 구매 영수증을 보관하세요.
