1. 서론
The Avaya J100 Wireless Module (model 700512402) is an optional hardware accessory designed to enhance the connectivity of compatible Avaya J129, J179, and K155 IP Phones. This module provides seamless Wi-Fi and Bluetooth capabilities, allowing for greater flexibility in phone placement and headset usage.
This manual provides essential information for the proper installation, operation, and maintenance of your J100 Wireless Module. Please read these instructions carefully before proceeding with installation or use.
Image 1: Avaya J100 Wireless Module. This image displays the compact design of the module, showing its connectors and casing.
2. 안전 정보
- Always disconnect the IP Phone from its power source before installing or removing the J100 Wireless Module.
- Handle the module with care to avoid damage to its electronic components.
- 모듈을 습기, 극한 온도 또는 직사광선에 노출시키지 마십시오.
- Ensure proper ventilation around the IP Phone after installation.
- Only use the module with compatible Avaya IP Phones as specified.
3. 패키지 내용
패키지에 다음 품목이 포함되어 있는지 확인하십시오.
- Avaya J100 Wireless Module (700512402)
- Quick Start Guide or Documentation (if included)
If any items are missing or damaged, please contact your vendor or Avaya support.
4. 설정 및 설치
Follow these steps to install the Avaya J100 Wireless Module into your compatible Avaya IP Phone:
- 휴대폰 전원 끄기: Disconnect the power cable from your Avaya J129, J179, or K155 IP Phone.
- 모듈 슬롯을 찾으십시오: Identify the designated slot for the wireless module on the back or side of your IP Phone. This slot is typically covered by a removable panel.
- 커버 제거: Carefully remove the cover panel from the module slot. This may involve gently prying it off or unscrewing a small screw, depending on your phone model.
- 모듈 삽입: Align the Avaya J100 Wireless Module with the slot and gently insert it until it is fully seated. Ensure the connectors are properly aligned to avoid damage.
- Secure Module (if applicable): If your phone model requires it, secure the module with any screws that were removed from the cover panel.
- 커버 교체: Reattach the cover panel to the module slot.
- 휴대폰 전원 켜기: Reconnect the power cable to your IP Phone. The phone will power on and automatically detect the newly installed J100 Wireless Module.
Once the phone powers on, it should recognize the module, and you will be able to configure Wi-Fi and Bluetooth settings through the phone's menu.
5. 사용 설명서
5.1. Wi-Fi 연결
To connect your Avaya IP Phone to a Wi-Fi network:
- Access the phone's menu and navigate to the "Settings" or "Network" options.
- Select "Wi-Fi" or "Wireless Settings."
- Enable Wi-Fi if it is not already active.
- The phone will scan for available Wi-Fi networks. Select your desired network from the list.
- Enter the Wi-Fi password (if required) using the phone's keypad.
- Confirm the connection. The phone should now be connected to the Wi-Fi network.
5.2. 블루투스 연결
To pair a Bluetooth headset or other device with your Avaya IP Phone:
- Ensure your Bluetooth device is in pairing mode (refer to your device's manual for instructions).
- On your Avaya IP Phone, navigate to the "Settings" or "Bluetooth" menu.
- Enable Bluetooth if it is not already active.
- The phone will scan for nearby Bluetooth devices. Select your device from the list.
- If prompted, enter the pairing code (usually "0000" or "1234" for headsets, or as specified by your device).
- Confirm the pairing. Once paired, your Bluetooth device should be ready for use with the phone.
메모: Some Bluetooth headsets may enter a power-saving mode when not in use, which could lead to a slight delay in call alerts. This is normal behavior for certain devices.
6. 유지관리
- 청소: Use a soft, dry cloth to clean the exterior of the module and the phone. Do not use liquid cleaners or aerosols.
- 저장: If removing the module for extended periods, store it in a cool, dry place, away from direct sunlight and extreme temperatures.
- 펌웨어 업데이트: Ensure your Avaya IP Phone's firmware is up to date, as this can improve module performance and compatibility. Refer to your phone's documentation or Avaya support for firmware update procedures.
7. 문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| Module not detected by phone. | Module not properly seated; phone not restarted after installation. | Ensure the module is fully inserted into its slot. Power cycle the IP Phone. |
| Wi-Fi 네트워크에 연결할 수 없습니다. | Incorrect password; network out of range; Wi-Fi disabled. | Verify the Wi-Fi password. Move the phone closer to the access point. Ensure Wi-Fi is enabled in phone settings. |
| Bluetooth 장치가 페어링되지 않습니다. | Device not in pairing mode; Bluetooth disabled on phone; device out of range. | Put the Bluetooth device into pairing mode. Ensure Bluetooth is enabled on the phone. Move devices closer. |
| Intermittent Bluetooth connection or missed call alerts. | Bluetooth device power-saving mode; environmental interference. | This can be normal for some Bluetooth devices. Ensure the headset is fully charged. Minimize interference from other wireless devices. |
8. 사양
- 모델 번호: 700512402
- 상표: 아바야
- 호환 장치: Avaya J129, Avaya J179, Avaya K155 IP Phones
- 하드웨어 인터페이스: Bluetooth, Ethernet (via phone connection)
- 데이터 링크 프로토콜 : Bluetooth, Ethernet (via phone connection)
- 데이터 전송 속도: Up to 100 Megabits Per Second (via Ethernet, module provides wireless)
- 품목 무게: 약 1.13온스(32그램)
- 패키지 크기: 약 4.96 x 3.11 x 1.73인치
- 첫 번째 이용 가능: 18년 2019월 XNUMX일
9. 보증 및 지원
For warranty information, please refer to the documentation provided with your original Avaya IP Phone or contact your authorized Avaya reseller. Avaya provides technical support for its products. For assistance, visit the official Avaya support web사이트 또는 고객 서비스 부서에 문의하십시오.
You can find more information and support resources on the official Avaya web대지: www.avaya.com/support
