1. 서론
The SINOTIMER MC101-611 is a universal intelligent temperature control meter designed for precise temperature and humidity management. It features a clear LCD display for process value (PV) and set value (SV), along with various output and alarm functions. This manual provides essential information for the safe and effective operation of your device.
그림 1.1: 전면 view of the MC101-611 Temperature Control Meter, showing the dual digital display and control buttons.
2. 안전 정보
- 설치 및 작동 전에 모든 지침을 주의 깊게 읽으십시오.
- 전원 공급 장치 볼륨을 확인하십시오.tage matches the device's requirements (85-265V AC, 50/60Hz).
- All wiring should be performed by a qualified electrician to prevent electric shock or damage to the device.
- 과도한 습기, 먼지 또는 부식성 가스가 있는 환경에서는 장치를 작동하지 마십시오.
- 유지보수 또는 배선 변경 작업을 하기 전에 전원을 차단하십시오.
- 기기를 강한 전자기파 간섭으로부터 멀리하십시오.
3. 제품 특징
- Universal input for various temperature sensors (K, J, E, T, R, S, B, Pt100, Cu50).
- Dual digital display for Process Value (PV) and Set Value (SV).
- Multiple control outputs: Relay and SSR (Solid State Relay).
- Alarm functions (AL1, AL2) for high/low limits.
- PID auto-tuning function for precise control.
- 넓은 작동 온도 범위.
- Compact and easy-to-install design.
4. 패키지 내용
- 1 x SINOTIMER MC101-611 Temperature Control Meter
- 1 x Mounting Bracket (as shown in Figure 4.1)
- 1 x 사용자 매뉴얼(이 문서)
Figure 4.1: The MC101-611 unit alongside its included mounting bracket, essential for panel installation.
5. 설정
5.1 장착
The MC101-611 is designed for panel mounting. Cut an appropriate opening in your control panel and insert the meter. Secure it from the rear using the provided mounting bracket. Ensure a snug fit to prevent vibration.
5.2 배선
Refer to the wiring diagram on the side of the unit and Figure 5.1 for correct connections. Ensure all connections are secure and insulated. Incorrect wiring can damage the device or pose a safety hazard.
- 터미널 1 및 2: AC Power Supply (85-265V AC, 50/60Hz)
- 터미널 3 및 4: Main Output (OUT) - Normally Open (NO) and Normally Closed (NC) contacts for Relay output.
- 터미널 6 및 7: Alarm Output (ALM) - Relay contacts for alarm.
- 터미널 8, 9, 10: Sensor Input (RTD/TC) - Connect your temperature sensor here. Refer to the sensor's manual for correct polarity/connection type.
- 터미널 11 및 12: SSR Output - For connecting to a Solid State Relay.
Figure 5.1: Detailed wiring diagram on the side of the MC101-611, indicating connections for power, output, alarm, and sensor input.
6. 사용 설명서
6.1 디스플레이 오버view
The meter features a dual display:
- PV(공정가치): The upper red display shows the current measured temperature/humidity.
- SV(설정값): The lower green display shows the desired set point.
- 출력 표시기: Illuminates when the main output is active.
- 있음 표시기: Illuminates when the auto-tuning function is active.
- AL1/AL2 지표: Illuminate when Alarm 1 or Alarm 2 conditions are met.
6.2 버튼 기능
- 설정 버튼: 파라미터 설정 모드로 진입하고 선택 사항을 확인하는 데 사용됩니다.
- < / R/S Button: Used to shift digits during setting or to reset alarms.
- ▼ (아래) 버튼: Decreases the value of a parameter or set point.
- ▲ (위) 버튼: Increases the value of a parameter or set point.
6.3 Setting the Temperature/Humidity Set Point (SV)
- 정상 작동 모드에서는 다음을 누릅니다. 세트 button once. The SV display will begin to flash.
- 사용하세요 ▲ (위) 그리고 ▼ (Down) buttons to adjust the SV to your desired value. Use the < / R/S 마우스 커서를 이동시켜 더 빠르게 조정할 수 있는 버튼입니다.
- 를 누르세요 세트 버튼을 다시 눌러 새 SV를 확인하고 설정 모드를 종료합니다.
6.4 고급 매개변수 설정
To access advanced parameters (e.g., input type, control mode, alarm settings, PID parameters), press and hold the 세트 button for approximately 3-5 seconds until the first parameter code appears on the PV display. Use the ▲ (위) 그리고 ▼ (Down) buttons to navigate through parameters and the 세트 button to enter and confirm values. Refer to the detailed parameter list in the full technical manual for specific codes and their functions.
7. 유지관리
- 청소: 디스플레이를 닦고 casin부드럽고 마른 천으로 닦아주세요. 연마성 세제나 용제는 사용하지 마세요.
- 점검: 주기적으로 배선 연결 부분을 점검하여 느슨함이나 부식이 없는지 확인하세요.
- 저장: If storing the device for an extended period, ensure it is kept in a dry, dust-free environment within its specified storage temperature range.
8. 문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 디스플레이가 비어 있습니다. | No power supply; Incorrect wiring; Device fault. | 전원 연결 및 볼륨을 확인하세요tage; Verify wiring according to diagram; Contact support if problem persists. |
| PV 디스플레이에 'HHHH' 또는 'LLLL'이 표시됩니다. | Sensor open circuit (HHHH) or short circuit (LLLL); Sensor not connected; Incorrect sensor type setting. | Check sensor wiring; Ensure sensor is connected; Verify sensor type setting in parameters matches connected sensor. |
| 출력이 활성화되지 않습니다 | SV not reached; Control mode incorrect; Output wiring issue. | Adjust SV; Check control mode (e.g., heating/cooling); Verify output wiring. |
| 온도 측정이 정확하지 않습니다 | Sensor calibration needed; Sensor damaged; External interference. | Perform sensor calibration (if supported); Replace sensor; Relocate device away from interference sources. |
9. 사양
Figure 9.1: Product label on the side of the MC101-611, detailing model, range, output, and power supply specifications.
| 매개변수 | 값 |
|---|---|
| 모델 | MC101-611 |
| 범위 | 0-1300°C K (Configurable for various sensor types) |
| 온도 단위 | Celsius/Fahrenheit (Selectable) |
| 산출 | Relay/SSR |
| 경보 | ALM1 |
| 공급량tage | 85-265V 교류, 50/60Hz |
| 디스플레이 유형 | 액정표시장치 |
| 품목 무게 | 5.1 온스 |
| 패키지 크기 | 3.9 x 2.8 x 2.4 인치 |
10. 보증 및 지원
This product comes with a standard manufacturer's warranty. Please refer to your purchase documentation for specific warranty terms and conditions. For technical support, troubleshooting assistance, or warranty claims, please contact the SINOTIMER customer service through the retailer where the product was purchased or visit the official SINOTIMER web연락처 정보 사이트.
