소개
This manual provides essential instructions for the safe and efficient operation of your Ahuja UB-30 25W PA Amplifier. 사용하기 전에 이 설명서를 자세히 읽어주세요. amp증폭기를 설치하고 나중에 참조할 수 있도록 보관하십시오.
The Ahuja UB-30 is a compact 25W Public Address (PA) amplifier designed for various audio applications, offering versatile input and output options.
중요 안전 지침
- 전원: 연결하다 amplifier only to the specified AC mains voltage (220-240V, 50/60Hz) or a 12V DC car battery.
- 접지: Ensure the equipment is properly earthed. Disconnect from mains before removing any covers.
- 통풍: 환기구를 막지 마십시오. 과열을 방지하기 위해 장치 주변에 충분한 공기 흐름을 확보하십시오.
- 수분: 노출시키지 마십시오 amp화재나 감전을 방지하기 위해 비나 습기에 노출되는 것을 방지합니다.
- 서비스: 모든 정비는 자격을 갖춘 서비스 담당자에게 맡기십시오. 이 제품을 직접 정비하려고 하지 마십시오.
- 놓기: 배치하다 amplifier on a stable, flat surface. Avoid placing it near heat sources or in direct sunlight.
제품 끝view
The Ahuja UB-30 amplifier features multiple input channels and various speaker output options for flexible connectivity.
그림 1: 앞쪽 view of the Ahuja UB-30 amplifier, showing the control panel and power cable.
그림 2: 뒤쪽 view of the Ahuja UB-30 amplifier, displaying the power input, fuse, and speaker output terminals.
제어 및 연결
전면 패널 컨트롤
그림 3: 상세한 view 의 amplifier's front panel, highlighting input jacks and control knobs.
- MIC-1 Input: 마이크 입력용 6.3mm 잭.
- MIC-1 볼륨 조절: Adjusts the volume level for MIC-1.
- MIC-2/AUX Input: 6.3mm jack for microphone or auxiliary input.
- MIC-2/AUX 볼륨 조절: Adjusts the volume level for MIC-2 or AUX input.
- 톤 컨트롤: Adjusts the tonal balance (bass/treble) of the output. Labeled 'CUT' to 'FLAT'.
- 전원 스위치: 토글 amplifier's power ON/OFF.
- 전원 표시기: 다음과 같은 경우에 켜집니다. ampliifier의 전원이 켜져 있습니다.
후면 패널 연결
그림 4: 상세한 view 의 amplifier's rear panel, showing power input, fuse, and speaker terminals.
- AC 전원 입력: Connects to 220-240V AC mains supply.
- DC 전원 입력: Terminals for 12V DC car battery connection. Observe polarity (+/-).
- DC FUSE: T 6A L fuse for DC power protection.
- 스피커 출력: Screw terminals for connecting speakers. Options include COM (Common), 4Ω, 8Ω, 16Ω, and 100V line output.
설정
1. 언박싱 및 검사
조심스럽게 amplifier from its packaging. Inspect the unit for any signs of damage. Ensure all components are present.
2. 전원 연결
The UB-30 can be powered by either AC mains or a 12V DC battery.
- AC Mains (220-240V): Connect the provided AC power cord to the AC power input on the rear panel and then to a suitable wall outlet.
- DC Battery (12V): For portable use, connect a 12V car battery to the DC input terminals on the rear panel. Ensure correct polarity: positive (+) to positive, negative (-) to negative.
주의: 항상 amplifier is switched OFF before connecting or disconnecting power sources.
3. 스피커 연결
Connect your speakers to the appropriate terminals on the rear panel. Match the speaker impedance to the amplifier's output impedance for optimal performance and to prevent damage.
- Connect the common (negative) terminal of your speaker(s) to the 코. 터미널에 amp리퍼.
- Connect the positive terminal of your speaker(s) to the 4Ω, 8Ω, 또는 16Ω terminal, matching your speaker's impedance.
- For 100V line speakers, connect to the 100V 터미널 및 코.. Ensure your speakers are compatible with 100V line systems.
중요한: Do not connect speakers to multiple impedance terminals simultaneously. Ensure all connections are secure.
4. Input Device Connection
- 마이크: 마이크를 연결하세요 마이크-1 그리고/또는 MIC-2/AUX 6.3mm input jacks on the front panel.
- 보조 장치: Connect audio sources like smartphones, CD players, or laptops to the MIC-2/AUX input jack using an appropriate cable.
작동 지침
1. 전원 켜기
- Ensure all volume controls (MIC-1, MIC-2/AUX) are set to their minimum position (fully counter-clockwise).
- 를 누르세요 힘 switch on the front panel to the 'ON' position. The power indicator light will illuminate.
2. 볼륨 조절
- For MIC-1, slowly turn the MIC-1 볼륨 조절 clockwise until the desired sound level is achieved.
- For MIC-2 or AUX input, slowly turn the MIC-2/AUX Volume Control clockwise until the desired sound level is achieved.
- Avoid setting the volume too high, which can cause distortion or damage to speakers.
3. 음색 조정
사용하세요 톤 컨트롤 knob to adjust the frequency response of the amplifier. Turning it towards 'CUT' will reduce higher frequencies (treble), while turning it towards 'FLAT' will provide a more balanced, full-range sound.
4. 전원 끄기
- Turn all volume controls to their minimum position.
- 를 누르세요 힘 switch to the 'OFF' position. The power indicator light will turn off.
유지
청소
겉면을 닦아주세요 amplifier with a soft, dry cloth. Do not use liquid cleaners or abrasive materials, as they may damage the finish or internal components.
Fuse Replacement (DC Fuse)
만약 amplifier fails to power on when using DC battery power, the DC fuse may need replacement. The fuse is located on the rear panel.
- 중요한: Disconnect all power sources (AC and DC) before attempting to replace the fuse.
- Unscrew the fuse holder cap on the rear panel.
- Remove the old fuse and replace it with a new fuse of the same type and rating (T 6A L).
- Securely screw the fuse holder cap back into place.
주의: Always replace fuses with the specified type and rating to prevent damage to the amplifier or risk of fire.
문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| No power, power indicator off. |
|
|
| 소리가 출력되지 않습니다. |
|
|
| 왜곡된 소리. |
|
|
명세서
| 특징 | 세부 사항 |
|---|---|
| 전력 출력 | 30W RMS Max., 25W RMS at 10% THD |
| 입력 채널 | 2 × Mic (1.0mV / 4.7kΩ), 1 × Aux (100mV / 470kΩ) |
| 스피커 출력 | 4Ω, 8Ω, 16Ω & 100V Line |
| 주파수 응답 | 150~10,000Hz ±3dB |
| 전원 공급 장치 | AC: 220-240V 50/60Hz, DC: 12V (Car Battery) |
| 치수(길이 x 너비 x 높이) | 12 x 20 x 28 센티미터 |
| 품목 무게 | 2.9kg |
| 제조업체 | 아후자 |
| 원산지 | 인도 |
그림 5: Size comparison of the Ahuja UB-30 amplifier, illustrating its compact dimensions.
보증 및 지원
For warranty information and technical support, please refer to the documentation provided with your purchase or contact Ahuja customer service directly. Keep your purchase receipt as proof of purchase for warranty claims.
제조업체: 아후자
