Audio-Technica AT-LP60XBT-WH Fully Automatic Bluetooth Belt-Drive Stereo Turntable

소개

The Audio-Technica AT-LP60XBT-WH is a fully automatic belt-drive stereo turntable designed for both wired and wireless audio playback. It features Bluetooth wireless technology for connecting to compatible speakers, headphones, or other devices, including support for the aptX codec for enhanced sound quality. The turntable also offers traditional wired connectivity via its dual RCA output cable. Its automatic operation simplifies playback with front-panel controls for start, stop, and tonearm lift. The unit incorporates a dual magnet cartridge with a replaceable stylus and plays records at 33-1/3 and 45 RPM speeds.

This image displays the Audio-Technica AT-LP60XBT-WH turntable from an elevated angle. The unit is white and black, with a clear, hinged dust cover lifted open. The black platter, featuring the Audio-Technica logo, is visible, along with the tonearm and stylus. Control buttons for speed, start, and stop are located on the front panel.

패키지 내용

다음 품목이 모두 패키지에 포함되어 있는지 확인하세요.

• AT-LP60XBT-WH Turntable Unit
• Detachable RCA output cable (3.5 mm male to dual RCA male)
• 45RPM 어댑터
• 탈착식 힌지 더스트 커버

설정

1. 놓기: 턴테이블을 직사광선, 열원 및 과도한 진동을 피해 안정적이고 평평한 곳에 놓으십시오.
2. Install Platter and Belt:
   • 알루미늄 플래터를 턴테이블 스핀들에 조심스럽게 올려놓으세요.
   • Locate the drive belt, which is usually pre-installed on the underside of the platter or included separately.
   • Align the belt with the motor pulley, which is typically a small brass or plastic cylinder located near the spindle. Use the red tab to pull the belt over the motor pulley. Ensure the belt is not twisted.
   • 플래터 위에 펠트 매트를 놓습니다.
3. Install Dust Cover: Insert the hinges of the dust cover into the hinge holders at the rear of the turntable unit.
4. 전원에 연결: Connect the AC adapter to the turntable's power input and then plug it into a wall outlet.
5. 오디오 연결:
   • 유선 연결: Connect the included dual RCA output cable from the turntable's output jacks to the audio input of your amplifier, powered speakers, or stereo system. Ensure the PHONO/LINE switch on the rear of the turntable is set correctly (PHONO for phono input, LINE for line input).
   • 무선 연결(블루투스): Proceed to the Bluetooth Connectivity section for pairing instructions.

작동 지침

1. 전원 켜기: Press the power button on the front panel to turn on the turntable. The Bluetooth indicator will illuminate.
2. 속도 선택: Press the 'SPEED' button to select the appropriate playback speed for your record (33-1/3 RPM or 45 RPM).
3. 장소 기록: Place a record on the platter. If playing a 45 RPM single, use the included 45 RPM adapter.
4. 재생 시작: Press the 'START' button. The tonearm will automatically move to the beginning of the record and begin playback.
5. 재생 중지 : Press the 'STOP' button. The tonearm will automatically lift, return to its rest, and the platter will stop spinning.
6. Manual Tonearm Lift: Use the 'TONEARM LIFT' button to manually raise or lower the tonearm during playback if needed.

블루투스 연결

The AT-LP60XBT-WH turntable can connect wirelessly to Bluetooth-enabled speakers, headphones, or other audio devices.

1. 기기에서 블루투스를 활성화하세요. Ensure your Bluetooth speaker or headphones are in pairing mode. Refer to your device's manual for specific instructions.
2. Initiate Turntable Pairing: With the turntable powered on, press and hold the Bluetooth button (usually indicated by a Bluetooth symbol) on the turntable's front panel for a few seconds until the Bluetooth indicator light begins to flash rapidly. This indicates the turntable is in pairing mode.
3. 연결하다: Once the turntable and your Bluetooth device are successfully paired, the Bluetooth indicator light on the turntable will change from rapidly flashing to a steady blue light.
4. aptX 코덱: This turntable supports the aptX codec, which provides higher quality audio streaming over Bluetooth with compatible devices.

유지

• 먼지 커버: Keep the dust cover closed when not in use to protect the turntable from dust and debris. Clean the dust cover with a soft, dry cloth. Avoid using harsh chemicals.
• 스타일러스 관리: Gently clean the stylus regularly using a soft brush designed for stylus cleaning, brushing from back to front. A dirty stylus can degrade sound quality and damage records.
• 스타일러스 교체: The stylus is replaceable. Refer to the Audio-Technica website or your local dealer for compatible replacement styli.
• 턴테이블 본체: Wipe the turntable body with a soft, dry cloth. Do not use solvents or abrasive cleaners.

문제 해결

명세서

보증 및 지원

For detailed warranty information, product registration, and customer support, please refer to the documentation included with your Audio-Technica AT-LP60XBT-WH turntable or visit the official Audio-Technica website. Contact information for technical assistance and service may also be found there.