Surge Switchpad Pro 무선 컨트롤러 사용 설명서

소개

This manual provides instructions for the Surge Switchpad Pro Wireless Controller, designed for use with the Nintendo Switch. It covers essential information regarding setup, operation, maintenance, and troubleshooting to ensure optimal performance and user experience.

이미지: 앞면 view of the Surge Switchpad Pro Wireless Controller in blue, with its included USB-C charging cable.

패키지 내용

• Surge Switchpad Pro Wireless Controller
• USB-C 충전 케이블
• 사용자 설명서

컨트롤러 기능

• 6축 모션 제어: Compatible with motion-sensing games.
• 매크로 버튼 4개: Programmable rear paddle buttons for custom button combos.
• 충전식 550mAh 배터리 : Provides up to 12 hours of gameplay.
• 터보 기능: Assign Turbo to any face button or trigger.
• 무선 연결: Bluetooth connectivity for stable connection up to 25ft.

Image: Diagram highlighting key features of the Surge Switchpad Pro: Bluetooth Connection, Rumble Feedback, and Rechargeable battery.

설정

컨트롤러 충전하기

Before initial use, fully charge the controller. Connect the included USB-C cable to the controller's USB-C port and the other end to a USB power source (e.g., Nintendo Switch dock, computer, or USB wall adapter).

이미지: 밑면 view of the Surge Switchpad Pro, showing the USB-C charge port located between the R1 and L1 buttons.

The LED player indicators on the front of the controller will illuminate during charging and turn off when fully charged.

Nintendo Switch와 페어링

1. 닌텐도 스위치의 HOME 메뉴에서 '컨트롤러'를 선택하세요.
2. '그립/순서 변경'을 선택하세요.
3. On the Surge Switchpad Pro, press and hold the SYNC button (usually a small button on the top edge or back) for a few seconds until the LED player indicators begin to flash rapidly.
4. Once the controller is successfully paired, the player indicator(s) corresponding to its assigned player number will remain lit.

작동 지침

기본 제어

The Surge Switchpad Pro features standard Nintendo Switch controller button layouts, including A/B/X/Y buttons, directional pad, left and right analog sticks, L/R/ZL/ZR shoulder buttons, and Home, Capture, Plus (+), and Minus (-) buttons.

Image: A person holding and using the Surge Switchpad Pro Wireless Controller during gameplay.

Macro Button Programming

The 4 macro buttons (typically located on the rear of the controller) can be programmed to execute a sequence of button presses. Refer to the specific instructions provided with your controller for detailed programming steps, as this may vary slightly.

Turbo Function Activation

To activate Turbo functionality for a button:

1. 를 누르고 계세요 터보 단추.
2. While holding Turbo, press the desired button (e.g., A, B, X, Y, L, R, ZL, ZR) you wish to assign Turbo functionality to.
3. Release both buttons. The assigned button will now rapidly repeat its input when held down.

To deactivate Turbo for a button, repeat the process. To clear all Turbo settings, press and hold the Turbo button for 5 seconds.

Image: Close-up of the Surge Switchpad Pro showing the four LED player indicators below the Home button.

유지

청소

• 부드럽고 마른 천으로 컨트롤러를 닦으세요.
• 완고한 먼지에는 약간 damp천에 물이나 순한 세척액을 묻혀 닦으세요. 강한 화학 물질은 피하세요.
• 컨트롤러의 개구부에 액체가 들어가지 않도록 주의하세요.

저장

• 컨트롤러는 직사광선과 극한의 온도를 피해 서늘하고 건조한 곳에 보관하세요.
• 장기간 보관할 경우, 배터리 수명을 연장하려면 배터리를 부분적으로(약 50%) 충전해 두세요.

문제 해결

컨트롤러가 연결/페어링되지 않습니다

• 컨트롤러가 완전히 충전되었는지 확인하세요.
• Verify that the Nintendo Switch is updated to the latest system software.
• Try re-pairing the controller by following the 'Pairing with Nintendo Switch' steps in the Setup section.
• If multiple controllers are paired, try disconnecting other controllers from the Switch settings.
• 닌텐도 스위치 본체를 재시작하세요.

입력 지연 또는 연결 끊김

• Ensure you are within the 25ft wireless range of the Nintendo Switch.
• 다른 무선 기기(예: Wi-Fi 라우터, 전자레인지)로 인한 간섭을 최소화하십시오.
• Ensure the controller is fully charged. Low battery can affect wireless performance.

버튼이 응답하지 않음

• Check if the controller is properly paired and connected.
• Restart the controller by holding the Home button for 10 seconds, then pressing it again to turn it back on.
• If a specific button is stuck, gently clean around it to remove any debris.

명세서

보증 및 지원

Information regarding product warranty and customer support was not available in the provided product data. Please refer to the product packaging or the official Surge website for warranty details and support contact information.