1. 서론
Thank you for choosing the Emtek Wilshire 8579 Single Sided Deadbolt. This deadbolt is designed to provide enhanced security for your doors with its key lock mechanism and antique-style aesthetic. This manual provides essential information for proper installation, operation, and maintenance to ensure optimal performance and longevity of your deadbolt.
2. 안전 정보
- 설치 시에는 항상 장갑과 보안경과 같은 적절한 안전 장비를 착용하십시오.
- Ensure all components are handled carefully to prevent damage or injury.
- Do not use power tools on settings that could overtighten screws or damage the door or deadbolt components.
- 질식 위험을 방지하려면 작은 부품을 어린이의 손이 닿지 않는 곳에 보관하십시오.
- If you are unsure about any step of the installation process, consult a qualified locksmith or professional installer.
3. 패키지 내용
설치를 시작하기 전에 모든 부품이 있는지 확인하십시오.
- Exterior Key Cylinder Assembly (with square escutcheon)
- Interior Thumb Turn Assembly (with square escutcheon)
- 데드볼트 잠금장치
- 스트라이크 플레이트
- Reinforcement Plate (for strike plate)
- 장착 나사 (다양한 크기)
- 키 (일반적으로 2개)
4. 설정 및 설치
This section outlines the steps for installing your Emtek Wilshire 8579 Single Sided Deadbolt. Ensure your door is prepared with the necessary bore holes (typically 2-1/8 inch for the main body and 1 inch for the latch).
4.1 구성 요소 식별
This image displays the two main components of the Emtek Wilshire 8579 Single Sided Deadbolt. On the left is the exterior key cylinder with a square escutcheon plate. On the right is the interior thumb turn mechanism, also with a square escutcheon plate, which allows for manual locking and unlocking from the inside.
4.2 Install the Latch Mechanism
- Insert the deadbolt latch mechanism into the 1-inch bore hole on the edge of the door. Ensure the word "TOP" (if present) is facing upwards.
- Secure the latch mechanism with the two small screws provided.
4.3 Install the Exterior Key Cylinder
- Insert the exterior key cylinder assembly into the 2-1/8 inch bore hole from the outside of the door.
- Ensure the tailpiece (the small metal bar extending from the back of the cylinder) passes through the slot in the latch mechanism.
4.4 Install the Interior Thumb Turn Assembly
- From the inside of the door, align the interior thumb turn assembly with the exterior cylinder.
- Ensure the tailpiece from the exterior cylinder engages correctly with the thumb turn mechanism.
- Secure both assemblies together using the long mounting screws provided. Tighten screws evenly until snug, but do not overtighten.
4.5 Install the Strike Plate
- Close the door and mark the center of the deadbolt latch on the door frame.
- Chisel out a recess for the strike plate and reinforcement plate so they sit flush with the door frame.
- Drill a 1-inch hole approximately 1 inch deep for the deadbolt to extend into.
- Install the reinforcement plate, then the strike plate, securing them with the longer screws provided.
4.6 테스트 작동
With the door open, test the deadbolt by turning the thumb turn and using the key from the exterior. Ensure the bolt extends and retracts smoothly without binding. Close the door and test again to ensure proper alignment with the strike plate.
5. 사용 설명서
5.1 Locking the Deadbolt
- 외부에서: Insert the key into the keyway and turn it clockwise until the deadbolt fully extends into the door frame. Remove the key.
- 인테리어에서: Turn the thumb turn clockwise until the deadbolt fully extends into the door frame.
5.2 Unlocking the Deadbolt
- 외부에서: Insert the key into the keyway and turn it counter-clockwise until the deadbolt fully retracts. Remove the key.
- 인테리어에서: Turn the thumb turn counter-clockwise until the deadbolt fully retracts.
6. 유지관리
- 청소: Clean the deadbolt's exterior surfaces with a soft, damp 천으로 닦아주세요. 연마성 세제나 강한 화학 물질은 마감재를 손상시킬 수 있으므로 사용하지 마세요.
- 매끄럽게 하기: Periodically apply a small amount of graphite lubricant or a silicone-based spray lubricant into the keyway and the latch mechanism to ensure smooth operation. Do not use oil-based lubricants, as they can attract dust and grime.
- 조임: Check mounting screws periodically and tighten if necessary to prevent loosening over time.
7. 문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 데드볼트가 뻣뻣하거나 돌리기 힘듭니다. | Lack of lubrication; misalignment; worn components. | Apply lubricant to keyway and latch. Check for proper alignment of deadbolt and strike plate. |
| Key does not insert or turn smoothly. | 열쇠 구멍에 이물질이 끼어 있음; 열쇠가 휘어짐; 잘못된 열쇠임. | Clean keyway with compressed air. Try a different key. Ensure you are using the correct key. |
| 데드볼트가 완전히 확장되거나 수축되지 않습니다. | Misalignment of strike plate; obstruction in door frame; loose mounting screws. | Adjust strike plate position. Clear any obstructions. Tighten mounting screws. |
| Deadbolt rattles or feels loose. | 장착 나사가 느슨합니다. | 모든 고정 나사를 단단히 조이십시오. |
8. 사양
- 상표: 엠텍
- 모델: Wilshire 8579 Single Sided Deadbolt
- 잠금 유형: Key Lock (Single Sided)
- 재료: 금속
- 스타일: 고대 미술
- 모양: Round (deadbolt mechanism), Square (escutcheon plates)
- 컨트롤러 유형 : Mechanical knob (thumb turn)
- 추천 용도: Securing interior doors in residential or commercial buildings with traditional/vintage-스타일 인테리어
- 한국어: 789704091766
9. 보증 및 지원
Emtek products are manufactured to high-quality standards. Specific warranty details are typically provided with the product packaging or can be found on the official Emtek web사이트. 보증 청구를 위해 구매 증빙 자료를 보관하세요.
For technical assistance, replacement parts, or further inquiries, please contact Emtek customer support through their official web사이트 또는 구매 문서에 제공된 연락처 정보를 참조하세요.
