제품 끝view
The Emtek 7103 Passage Set is a high-quality knobset designed for doors that do not require a locking mechanism, such as closet doors, hallway doors, or pantry doors. This set includes a Madison Black Knob and a #3 Wrought Steel Rosette with a Flat Black Steel (FBS) finish. It is manufactured by Emtek and includes a standard rotation latch and strike plate. The knobset is designed for a standard 2-1/8 inch door preparation. The standard latch is for a 2-3/8 inch backset, with a 2-3/4 inch backset available if specified.
This image displays the Emtek 7103 Passage Set, featuring a round Madison Black Knob mounted on a rectangular Flat Black Wrought Steel Rosette. The knob has a smooth, glossy black finish, contrasting with the textured matte black finish of the rosette.
설정 및 설치
This section provides instructions for the proper setup and installation of your Emtek 7103 Passage Set.
시작하기 전에
- Ensure all components are present: knobset, rosette, latch, strike plate, and mounting screws.
- Verify door thickness and backset requirements. Standard backset is 2-3/8 inches. If 2-3/4 inches is required, ensure you have the correct latch.
- Tools required: Phillips head screwdriver, tape measure, pencil.
설치 단계
- 문 준비: Ensure the door has a standard 2-1/8 inch bore hole for the knobset and a 1-inch bore hole for the latch.
- 래치를 설치하십시오: Insert the latch into the edge of the door, ensuring the bevel faces the door frame. Secure with screws.
- Install the Exterior Knob/Rosette: Place the exterior knob and rosette assembly through the 2-1/8 inch bore hole, aligning the spindle with the latch mechanism.
- Install the Interior Knob/Rosette: Place the interior knob and rosette assembly onto the spindle, aligning the mounting posts with the holes on the exterior rosette.
- 집회 보안: Insert and tighten the mounting screws through the interior rosette into the exterior rosette. Do not overtighten.
- 스트라이크 플레이트 설치: Mark and chisel the door frame for the strike plate. Secure the strike plate with screws, ensuring the latch engages smoothly.
- 테스트 작업: Rotate the knobs to ensure the latch retracts and extends freely. Check for smooth operation from both sides of the door.
작동 지침
The Emtek 7103 Passage Set is designed for doors that do not require locking, such as closet doors, hallway doors, or pantry doors. It allows for free passage from both sides at all times.
- To open the door, simply turn the knob in either direction. The latch bolt will retract, allowing the door to open.
- To close the door, push the door shut. The latch bolt will automatically engage with the strike plate, holding the door closed.
유지
Proper maintenance will ensure the longevity and smooth operation of your Emtek 7103 Passage Set.
- 청소: Clean the knob and rosette surfaces with a soft, damp 천으로 닦으십시오. 마감재를 손상시킬 수 있는 연마성 세척제, 용제 또는 광택제는 사용하지 마십시오.
- 매끄럽게 하기: Periodically apply a small amount of silicone-based lubricant to the latch mechanism to ensure smooth operation. Do not use oil-based lubricants as they can attract dust and grime.
- 나사 조이기: Over time, mounting screws may loosen. Periodically check and gently tighten any loose screws to maintain stability. Do not overtighten.
- 점검: Regularly inspect the knobset for any signs of wear, damage, or misalignment.
문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 손잡이가 헐거워지거나 흔들거립니다. | 장착 나사가 느슨합니다. | Tighten the mounting screws on the interior rosette. |
| 잠금장치가 부드럽게 들어가지 않습니다. | 윤활 부족; 기계 장치 내부에 이물질이 있음. | Apply silicone-based lubricant to the latch bolt. Clean any visible debris. |
| 문이 제대로 닫히지 않거나 덜컹거립니다. | Strike plate misalignment; worn latch. | Adjust the strike plate position. If latch is worn, consider replacement. |
| Knob is stiff to turn. | Spindle misalignment; internal mechanism friction. | Loosen mounting screws slightly, adjust knob position, then retighten. Lubricate internal mechanism if accessible. |
명세서
- 모델: Emtek 7103 Passage Set
- 재료: Wrought Steel
- 손잡이 스타일: Madison Black Knob
- Rosette Style: #3 Rosette
- 마치다: Flat Black Steel (FBS)
- 도어 준비: Standard 2-1/8" bore hole
- 역수: Standard 2-3/8" (2-3/4" available upon request)
- 한국어: 751125555226
보증 및 지원
Emtek products are manufactured to high-quality standards. For specific warranty information regarding your Emtek 7103 Passage Set, please refer to the documentation provided with your purchase or visit the official Emtek web사이트. 보증 약관은 다를 수 있습니다.
For technical support, product inquiries, or assistance with installation or troubleshooting, please contact Emtek customer service directly. Their contact information can typically be found on their official web사이트 또는 제품 포장 내부에 있습니다.
제조업체: 엠텍
공식적인 Web대지: www.emtek.com
