1. 서론
This manual provides detailed instructions for the installation, programming, operation, and maintenance of your LiftMaster 892LT 2-Button Remote Control Transmitter. The 892LT remote is designed to operate up to two garage door openers or gate operators, offering a convenient way to access your property. It is compatible with LiftMaster Security+ 2.0, 315 MHz, and 390 MHz systems, and replaces older models such as 972LM, 372LM, and 62LM.
Please read this manual thoroughly before attempting to program or operate the remote control to ensure proper function and safety.
이미지 1.1: 앞면 view of the LiftMaster 892LT 2-Button Remote Control Transmitter.
2. 안전 정보
To reduce the risk of severe injury or death, observe the following safety precautions:
- Do not enable the garage door opener if the door is not balanced or if springs are broken.
- 리모컨은 항상 어린이의 손이 닿지 않는 곳에 보관하십시오.
- Operate the garage door opener only when the door is in full view막힘이 없고, 개폐 장치가 제대로 조정되어 있습니다.
- 어린이들이 리모컨이나 차고 문 개폐기를 가지고 놀지 못하게 하십시오.
- This remote control is not intended for use with any garage door opener manufactured before 1993 that does not have a safety reversal system.
3. 패키지 내용
패키지에 모든 품목이 들어 있는지 확인하세요.
- LiftMaster 892LT 2-Button Remote Control Transmitter
- CR2 Lithium Battery (pre-installed)
- 바이저 클립
4. 설정 및 프로그래밍
The 892LT remote control can be programmed to operate up to two different garage door openers or gate operators. Follow these steps to program your remote:
4.1. Locate the Learn Button on Your Opener
The location and color of the Learn button vary by garage door opener model. Refer to your garage door opener's manual if you cannot locate it. Common locations include the back or side panel of the motor unit.
Image 4.1: The 892LT remote supports Security+ 2.0 technology for enhanced security.
4.2. 프로그래밍 단계
- Press and Release the Learn Button: On your garage door opener, press and immediately release the Learn button. The Learn LED on the opener will glow steadily for 30 seconds.
- Press and Hold the Remote Button: Within 30 seconds, press and hold the button on your 892LT remote control that you wish to program.
- 리모컨 버튼에서 손을 떼세요: Release the remote button when the garage door opener lights flash or two clicks are heard. This indicates that the remote has been successfully programmed.
- 리모컨 테스트: Press the programmed button on your remote control. The garage door opener should activate.
If you are programming a second button for another opener, repeat the steps above, selecting a different button on the 892LT remote and the Learn button on the second opener.
Image 4.2: The 892LT features a multi-use design, allowing control of up to two devices.
5. 사용 설명서
Once programmed, operating your LiftMaster 892LT remote control is straightforward:
- 문을 열거나 닫으려면: Press the programmed button on your remote control. The garage door or gate will begin to move.
- 문을 멈추려면: Press the programmed button again while the door is in motion.
- 문을 반대로 열려면: 문이 움직이는 도중에 멈추면 버튼을 다시 누르면 반대 방향으로 움직입니다.
Ensure you have a clear line of sight to the garage door or gate when operating the remote to prevent accidents.
6. 유지관리
6.1. 배터리 교체
The 892LT remote uses one CR2 lithium battery. When the battery is low, the remote's range may decrease, or the LED indicator may not light up consistently.
- 원격 C를 엽니다asing: Use a small coin or screwdriver to gently pry open the remote control casing.
- 오래된 배터리 제거: 오래된 CR2 배터리를 조심스럽게 제거하세요.
- 새 배터리를 삽입하세요: 새 CR2 배터리를 양극(+)이 위를 향하게 하여 삽입하세요.
- C 닫기asing: 리모컨을 튕기세요asing를 다시 단단히 결합하세요.
6.2. 청소
Wipe the remote control with a soft, dry cloth. Do not use liquid cleaners or solvents, as they may damage the remote's electronics.
7. 문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 리모컨으로 문이 열리지 않습니다. | Remote is not programmed or battery is dead. | Re-program the remote (Section 4.2). Replace the battery (Section 6.1). |
| 리모컨의 작동 범위가 줄어들었습니다. | 배터리 부족 또는 간섭. | Replace the battery (Section 6.1). Check for sources of interference near the opener. |
| Opener lights flash but door does not move. | Safety sensors are obstructed or misaligned. | Check and clear any obstructions from the safety sensors. Align the sensors if necessary. |
8. 사양
- 모델: 892LT
- 버튼: 2
- 호환성: LiftMaster Security+ 2.0, 315 MHz, 390 MHz, 433 MHz
- 배터리: CR2 리튬 배터리 1개 (포함)
- 치수: 약 5.12 x 2.72 x 1.14cm(13 x 6.9 x 2.9인치)
- 무게: 약 2.08온스(0.06kg)
- 한국어: 734721923729
9. 보증 및 지원
보증 정보 및 기술 지원에 대해서는 제조업체의 공식 웹사이트를 참조하십시오. web해당 사이트를 방문하거나 고객 서비스 부서에 문의하세요. 구매 증빙 자료로 구매 영수증을 보관하세요.
