BFT TX4

BFT B RCB TX4 리모컨 사용 설명서

모델: TX4

1. 서론

This manual provides comprehensive instructions for the setup, operation, and maintenance of your BFT B RCB TX4 Remote Control. Please read this manual carefully before using the device to ensure proper functionality and longevity.

2. 제품 오버view

The BFT B RCB TX4 is an ergonomic radio frequency remote control designed for various compatible devices, including televisions, DVD/Blu-ray players, set-top boxes, and audio/video receivers. It features 12 buttons and operates with a range of up to 150 meters.

BFT B RCB TX4 Remote Control

그림 1: 앞쪽 view of the BFT B RCB TX4 Remote Control, showing its four main buttons and the BFT logo.

3. 설정 및 프로그래밍

The BFT B RCB TX4 remote control is designed for easy programming. The specific programming method may vary depending on the receiver unit it is being paired with. Below is a general programming procedure. Refer to your receiver's manual for precise instructions if these steps do not apply.

  1. 수신기를 준비하세요: Locate the programming button or learn mode activation on your compatible device (e.g., gate opener, garage door opener, or other receiver). This button is often labeled "PROG," "LEARN," or "SET."
  2. 학습 모드 활성화: Press and hold the programming button on your receiver until an indicator light (LED) illuminates or flashes, signifying that the receiver is in learn mode.
  3. 리모컨 프로그래밍하기: While the receiver is in learn mode, press and hold the desired button on your BFT B RCB TX4 remote control that you wish to assign to the function. Hold the button for approximately 2-3 seconds.
  4. 프로그래밍 확인: The indicator light on the receiver should change (e.g., flash rapidly, turn solid, or turn off) to confirm successful programming. Release the button on the remote control.
  5. 테스트 기능: Press the programmed button on your BFT B RCB TX4 remote control to test its operation with the receiver.
  6. Program Additional Buttons (if applicable): Repeat steps 2-5 for any other buttons you wish to program for different functions or devices.

메모: If programming fails, ensure the remote control has fresh batteries and that you are within the operational range of the receiver. Some receivers may require a specific sequence or a master remote for programming.

4. 사용 설명서

Once programmed, operating the BFT B RCB TX4 remote control is straightforward:

5. 유지관리

5.1 배터리 교체

The BFT B RCB TX4 remote control uses an alkaline battery, which is included with the device. When the remote's range decreases significantly or it stops responding, it is likely time to replace the battery.

  1. 배터리 칸 찾기: The battery compartment is typically located on the back or side of the remote control. It may be secured with a small screw or a clip.
  2. 개방형 구획: Use a small screwdriver or a coin to gently open the battery compartment cover.
  3. 오래된 배터리 제거: Carefully remove the old battery, noting its orientation (+/- terminals).
  4. 새 배터리를 삽입하세요: Insert a new alkaline battery of the same type, ensuring correct polarity.
  5. 구획 닫기: 배터리함 덮개를 교체하고 고정합니다.
  6. 시험: Test the remote control's functionality after replacing the battery.

5.2 청소

리모컨을 청소할 때는 부드럽고 마른 천을 사용하십시오. 연마성 세제, 용제 또는 과도한 습기는 기기를 손상시킬 수 있으므로 사용하지 마십시오.

6. 문제 해결

문제가능한 원인해결책
리모컨이 응답하지 않습니다.Dead or low battery. Incorrect programming. Out of range.Replace battery. Re-program the remote. Move closer to the receiver.
작동 범위가 감소했습니다.배터리 부족. 장애물. 간섭.Replace battery. Ensure clear line of sight. Check for sources of radio interference.
Remote programs but does not operate.Incorrect programming. Receiver issue.Verify programming steps with receiver manual. Check receiver's power and status.

7. 사양

8. 보증 및 지원

For warranty information or technical support, please refer to the documentation provided with your purchase or contact the retailer or manufacturer directly. Keep your proof of purchase for warranty claims.

제조사: 리모컨

관련 문서 - TX4

사전view BFT Mitto 2M/4M 원격 코딩 지침: 포괄적인 가이드
BFT Mitto 2M 및 4M 차고 및 게이트 개폐기용 리모컨을 프로그래밍하는 방법을 알아보세요. 이 가이드에서는 디지털 화면 유무에 따른 수신기 코딩 방법과 중요 안전 경고를 다룹니다.
사전view BFT Cell Switch Prime GSM Gate Opener - Installation & User Manual
Detailed installation and user manual for the BFT Cell Switch Prime, a GSM cellular gate opener and alarm signalling device. Covers system overview, installation, programming via app and SMS, features, troubleshooting, and parameter lists.
사전view BFT CLONIX1-2 롤링 코드 무선 조종 시스템 설치 설명서
본 문서는 BFT CLONIX1-2 롤링 코드 무선 조종 시스템의 설치, 프로그래밍 및 안전 지침을 제공합니다. 수신기 설치 방법, 표준 및 고급 방법을 사용한 송신기 프로그래밍 방법, 그리고 수신기 및 MITTO 송신기에 대한 기술 사양을 포함합니다.
사전view BFT Ecosol Quick Installation Guide for Libra UL-R, Ares, and Deimos BT
A quick installation guide for the BFT Ecosol Box, detailing connections to Libra UL-R, Ares, and Deimos BT gate systems, including harness assembly, wiring diagrams, and dipswitch programming.
사전view BFT MITTO 2B 리모컨 코딩 설명서 | 레트로 리모컨
게이트 개폐기용 BFT MITTO 2B 리모컨 코딩을 위한 단계별 가이드로, 기존 리모컨 및 수신기 LCD 화면 사용법을 다룹니다. 문제 해결 팁도 포함되어 있습니다.
사전view BFT Kustos Ultra BT A25/A40: 모든 설치 및 특정 기술 지침
Scopri la guida completa all'installazione e le 특정 tecniche per gli Operatori di cancelli a battente BFT Kustos Ultra BT A25 e A40. 정보tagliate su montaggio, cablaggio e prestazioni.