1. 서론
This instruction manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of the Hilti DX 351 powder-actuated fastening tool. It is crucial to read and understand all instructions and safety warnings before using the tool. Keep this manual accessible for future reference.
2. 안전 지침
Always adhere to general safety regulations and local accident prevention rules. Failure to follow these instructions may result in serious injury or property damage.
- 개인 보호 장비(PPE): Always wear eye protection, hearing protection, and safety gloves when operating the tool.
- 승인된 직원: Only trained and authorized personnel should operate this tool.
- 작업 영역: Ensure the work area is clear of bystanders and free from flammable materials.
- 도구 상태: 사용하기 전에 공구에 손상이 있는지 항상 점검하십시오. 손상된 공구는 사용하지 마십시오.
- Fastener and Cartridge Compatibility: Use only Hilti-approved fasteners and cartridges that are compatible with the DX 351.
- 도구를 자신이나 다른 사람을 향해 겨누지 마십시오.
- 저장: Store the tool, fasteners, and cartridges securely and out of reach of unauthorized persons.
3. 구성 요소 이상view
The Hilti DX 351 kit includes the following main components:
- DX 351 Basic Unit: The main body of the powder-actuated tool.
- X-P8S-351 Piston: An essential internal component for driving fasteners.
- Nail Magazine X-MX32 Assy: Attaches to the tool for sequential fastening of nails.
- DX 351 Cleaning Kit: Contains tools and brushes for routine maintenance.
- Case DX 351: For safe storage and transport of the tool and accessories.
- Concrete Nails X-P 22 MX (5000x): Fasteners designed for concrete applications.
- Cartridges 6.8/11 M.27 Cal Yellow (5000x): Powder loads used to power the tool.
4. 설정
Before operating the Hilti DX 351, ensure proper setup:
- Attach Magazine: Securely attach the X-MX32 nail magazine to the tool body. Refer to the tool's markings for correct alignment and locking mechanism.
- Load Cartridges: Insert the 6.8/11 M.27 cal yellow cartridges into the cartridge strip. Ensure the cartridges are fully seated and the strip is correctly loaded into the tool's cartridge chamber.
- 하중 고정 장치: Insert the X-P 22 MX concrete nails into the magazine. Ensure they are properly aligned and feed smoothly.
- 전력 조절: Adjust the power regulation dial (typically located at the rear of the tool) to the appropriate setting for the application and base material. Start with a lower setting and increase if necessary.
- 기능 점검: Perform a quick function check to ensure all components are securely attached and operating freely.
5. 사용 설명서
안전하고 효과적인 작업을 위해 다음 단계를 따르세요.
- PPE 착용: 항상 눈과 귀 보호 장비를 포함한 적절한 개인 보호 장비를 착용하세요.
- 위치 도구: Place the tool firmly and perpendicularly against the base material where the fastener is to be driven. Ensure the contact element is fully depressed.
- Initiate Fastening: While maintaining firm pressure against the base material, pull the trigger to fire the cartridge and drive the fastener.
- 방출 압력: After firing, release pressure from the tool and lift it from the work surface.
- 제대로 잠겼는지 확인하세요: Inspect the driven fastener to ensure it is properly seated. Adjust power settings if necessary for subsequent fastenings.
- Clearing Misfires: In case of a misfire, keep the tool pressed against the work surface for at least 5 seconds. Then, carefully remove the cartridge strip and dispose of the misfired cartridge according to local regulations. Never attempt to re-fire a misfired cartridge.
6. 유지관리
Regular maintenance ensures the longevity and safe operation of your Hilti DX 351 tool.
- 매일 청소: After each use, or at least daily, clean the tool using the provided DX 351 Cleaning Kit. Pay special attention to the piston, barrel, and magazine areas to remove powder residue and debris.
- 점검: Regularly inspect the piston, buffer, and other wear parts for signs of damage or excessive wear. Replace worn components immediately with genuine Hilti parts.
- 매끄럽게 하기: Apply a thin layer of Hilti lubricant to moving parts as indicated in the detailed service instructions (not provided here, but implied).
- 저장: Store the clean and dry tool in its case, away from moisture and extreme temperatures. Remove all cartridges and fasteners before storage.
- 전문적인 서비스: For complex repairs or comprehensive servicing, contact an authorized Hilti service center.
7. 문제 해결
This section addresses common issues you might encounter with the Hilti DX 351.
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 도구가 발사되지 않습니다. | Insufficient pressure on base material; no cartridge loaded; faulty cartridge; tool dirty. | Apply firm pressure; load cartridge; replace cartridge; clean tool. |
| 체결 부품이 완전히 조여지지 않았습니다. | Power setting too low; incorrect fastener for material; worn piston/buffer. | Increase power setting; use appropriate fastener; inspect and replace worn parts. |
| Cartridge misfire. | Defective cartridge; tool not fully depressed; dirty firing pin area. | Keep tool pressed for 5s, then remove and dispose of cartridge; ensure full depression; clean tool. |
| Magazine jam. | Debris in magazine; bent fasteners; incorrect fastener loading. | Clear debris; use undamaged fasteners; ensure correct loading. |
If problems persist after attempting these solutions, contact Hilti customer service or an authorized service center.
8. 사양
- 모델: Hilti DX 351
- 부품 번호: 3553035
- 포함된 구성 요소: DX351 Basic unit, X-P8S-351 Piston, Nail magazine X-MX32 assy, DX 351 Cleaning Kit, Case DX 351, 5000x Concrete nail X-P 22 MX, 5000x Cartridge 6.8/11 M.27 cal yellow
- 패스너 유형: X-P 22 MX Concrete Nails
- 카트리지 유형 : 6.8/11 M.27 Cal Yellow
- 제조업체: 힐티
- 스타일: 현대의
- 필요한 배터리: 아니요
9. 보증 및 지원
Hilti products are designed for durability and reliability. For information regarding product warranty, service, or technical support, please refer to the official Hilti website or contact your local Hilti representative. Keep your purchase receipt for warranty claims.
더 자세한 도움을 받으시려면 힐티 공식 웹사이트를 방문하세요. web대지: www.hilti.com
