Skytech 9800332 TS/R-2 Wireless Wall Mounted LCD Fireplace Remote Control Thermostat

소개

The Skytech 9800332 TS/R-2 system is designed to provide a safe, reliable, and user-friendly remote control solution for gas heating appliances. This manual will guide you through the installation, operation, and maintenance of your new wireless thermostat system.

중요한 안전 정보

Please read and understand all instructions before installing or operating this product. Failure to follow these instructions may result in property damage, personal injury, or death. Keep this manual for future reference.

• 배선 작업에 자신이 없다면 반드시 자격을 갖춘 전문가에게 맡기십시오.
• Always turn off the gas supply to the appliance before performing any installation or maintenance.
• Do not expose the remote control or receiver to water or extreme temperatures.
• Replace batteries regularly to ensure proper operation and prevent leakage.
• This system is intended for use with gas heating appliances only.

패키지 내용

패키지에 모든 품목이 들어 있는지 확인하세요.

• 송신기(리모컨)
• 수신기 박스
• 월 클립
• 월 플레이트
• 설치 지침
• Batteries (for transmitter and receiver)
• Temperature Sensor (integrated into the transmitter)

제품 끝view

The Skytech 9800332 TS/R-2 is a wireless, wall-mounted thermostat system designed for convenient control of your fireplace. It features a clear LCD display and simple three-button operation.

그림 1: Skytech 9800332 TS/R-2 Wireless Thermostat. The unit features an LCD screen displaying '72°F' and 'ROOM SET TEMP', with 'SKYTECH' branding below. At the bottom are three buttons: an 'ON' arrow button, a 'SET' button, and an 'OFF' arrow button.

주요 특징:

• 3-Button On/Set/Off wall mounted thermostat with LCD display
• LCD displays room and thermostat set temperature in °F or °C
• Battery powered receiver box with learn function and On/Remote/Off slider switch
• Receiver can be installed in wall, on the hearth or under the fireplace behind the control access panel
• Lighted display for easy view잉
• 배터리 부족 표시기

설정 및 설치

1. 배터리 설치

Install the provided batteries into both the transmitter (remote control) and the receiver box. Ensure correct polarity.

2. 수신기 배치

The receiver box can be installed in various locations:

• Inside the wall (using the wall plate)
• On the hearth
• Under the fireplace, behind the control access panel

Ensure the receiver is placed in a location where it can receive signals from the transmitter and is not exposed to excessive heat.

3. 수신기 배선

Connect the receiver to your gas heating appliance's control valve according to the appliance manufacturer's instructions. Typically, this involves connecting two low-voltage wires from the receiver to the appliance's millivolt or 24V control terminals. Consult a qualified technician if you are unsure about wiring.

4. Pairing (Learn Function)

송신기와 수신기 간의 통신을 설정하려면:

1. Locate the "LEARN" button on the receiver box.
2. Press and hold the "LEARN" button until you hear a beep or see an indicator light flash.
3. Within 20 seconds, press any button on the transmitter.
4. The receiver will beep or flash again to confirm successful pairing.

Test the connection by pressing the ON/OFF buttons on the transmitter.

작동 지침

1. 전원 켜기/끄기

• To turn the fireplace ON, press the ON (Up Arrow) 송신기의 버튼입니다.
• To turn the fireplace OFF, press the OFF (Down Arrow) 송신기의 버튼입니다.

2. 온도 설정

The LCD displays both the current room temperature and the set temperature.

1. 를 누르세요 세트 button once. The set temperature will flash.
2. 사용하세요 ON (Up Arrow) or OFF (Down Arrow) 버튼을 눌러 원하는 온도를 조절하세요.
3. 누르다 세트 again to confirm, or wait a few seconds for the setting to automatically save.

3. 화씨와 섭씨 간 전환

온도 표시 단위를 변경하려면:

• With the display showing the room temperature, press and hold the 세트 button for approximately 5 seconds until the unit changes.

4. Receiver Slider Switch

The receiver box has a slider switch with three positions:

• 에: Manually turns the fireplace ON, bypassing the remote control.
• 먼: Allows the fireplace to be controlled by the wireless transmitter. This is the standard operating position.
• OFF : Manually turns the fireplace OFF, bypassing the remote control.

유지

배터리 교체

When the low battery indicator appears on the LCD, or if the system becomes unresponsive, replace the batteries in both the transmitter and receiver. Use fresh alkaline batteries of the specified type (refer to specifications). Dispose of old batteries responsibly.

청소

Wipe the surfaces of the transmitter and receiver with a soft, dry cloth. Do not use abrasive cleaners or immerse the units in water.

문제 해결

명세서

보증 및 지원

For warranty information and technical support, please refer to the documentation included with your purchase or contact SkyTech customer service directly. Keep your proof of purchase for warranty claims.

제조업체: 스카이텍