Skytech 9800325 SKY-3301P2 백라이트 프로그래밍 가능 벽난로 리모컨 사용 설명서

소개

This manual provides comprehensive instructions for the installation, operation, and maintenance of the Skytech 9800325 SKY-3301P2 remote control system. This system is designed to offer safe, reliable, and user-friendly control for gas heating appliances. It supports both thermostatic and manual operation from the transmitter.

The system utilizes radio frequencies (RF) for communication within a 20-foot range, employing non-directional signals. Each system operates on one of 1,048,567 security codes, pre-programmed at the factory. It is essential to match the remote receiver's code to that of the transmitter before initial use.

패키지 내용

Upon unpacking, verify that all components are present and undamaged. The package should include:

• Transmitter (Remote Control Unit)
• 수신기 유닛
• Wall Holder for Transmitter
• 월 플레이트
• 설치 지침
• Batteries (2 AAA for transmitter, 4 AA for receiver)

이미지 1: 위에view of the Skytech 9800325 SKY-3301P2 remote control system, showing the handheld transmitter, the wall-mounted receiver, and the wired receiver box.

설정 및 설치

1. 배터리 설치

송신기: Open the battery compartment on the back of the transmitter and insert two (2) AAA batteries, observing the correct polarity. Close the compartment securely.

수화기: Open the battery compartment on the receiver unit and insert four (4) AA batteries, observing the correct polarity. Close the compartment securely.

2. Receiver Placement and Wiring

The receiver can be installed in the wall, on the hearth, or under the fireplace behind the control access panel. Ensure the receiver is placed in a location that allows for proper signal reception from the transmitter and is not exposed to excessive heat.

Connect the two wires from the receiver to the appropriate terminals on your gas heating appliance's control valve. Refer to your appliance's manual for specific wiring instructions. Ensure all connections are secure and properly insulated.

이미지 2: Close-up of the receiver unit, showing the 'OFF', 'REMOTE', 'ON' slider switch and 'LEARN' button. This unit connects to the fireplace.

3. Matching Security Codes (Learning Function)

The transmitter and receiver are factory-matched. However, if they lose synchronization or if you are replacing a component, you may need to re-match them:

1. Ensure batteries are installed in both the transmitter and receiver.
2. Locate the 'LEARN' button on the receiver unit.
3. Press and hold the 'LEARN' button on the receiver until you hear a series of beeps (approximately 1-2 seconds).
4. Within 10 seconds, press any button on the transmitter. The receiver will emit another series of beeps, confirming that the codes have been matched.

If the matching process fails, repeat the steps. Ensure the transmitter is within 20 feet of the receiver during this process.

작동 지침

송신기 제어

이미지 3: Close-up of the handheld transmitter, showing the backlit LCD display with room temperature and set temperature, and the 'DOWN', 'MODE', 'UP' buttons. The flip cover conceals 'PROG' and 'SET' buttons.

• 위로 버튼: 온도 설정을 높이거나 메뉴 옵션을 탐색합니다.
• 다운 버튼: 온도 설정을 낮추거나 메뉴 옵션을 탐색합니다.
• MODE 버튼: Cycles through operating modes (ON, THERMO, OFF, PROGRAM).
• PROG Button (under flip cover): Used for programming thermostat schedules.
• SET Button (under flip cover): Used to confirm settings or enter programming mode.

Receiver Slider Switch

The receiver unit has a three-position slider switch:

• 에: Manually turns the appliance ON, bypassing remote control.
• 먼: Allows the appliance to be controlled by the transmitter.
• OFF : Manually turns the appliance OFF, bypassing remote control.

For normal operation with the remote control, ensure the receiver switch is set to 원격.

작동 모드

를 누르세요 방법 button on the transmitter to cycle through the following modes:

• 에: The appliance will turn on and remain on until switched off.
• 써모: The appliance will operate based on the set temperature. When the room temperature falls below the set temperature, the appliance will turn on. When the room temperature rises above the set temperature, the appliance will turn off.
• OFF : The appliance will remain off.
• 프로그램: The appliance will follow the programmed schedule for temperature control.

Setting the Temperature (THERMO Mode)

1. 를 누르세요 방법 button until "THERMO" is displayed on the LCD.
2. 사용하세요 UP or 아래에 buttons to adjust the desired set temperature. The display will show both the current room temperature and the set temperature.

Programming a Schedule (PROGRAM Mode)

The 3301P2 allows for programmable temperature settings. Lift the flip cover on the transmitter to access the 음식물 그리고 세트 버튼.

1. 를 누르세요 방법 button until "PROGRAM" is displayed on the LCD.
2. 를 누르세요 음식물 버튼을 눌러 프로그래밍 모드로 들어갑니다.
3. 사용하세요 UP or 아래에 buttons to adjust the time and temperature settings for each program period (P1, P2).
4. 누르다 세트 각 설정을 확인하고 다음 설정으로 이동합니다.
5. The system typically allows for two program periods (P1 for morning/day, P2 for evening/night) with separate ON/OFF times and temperatures. Consult the detailed instructions provided with the product for specific programming steps, as these can be intricate.

메모: The programming interface may require careful attention to detail. If you encounter difficulties, refer to the troubleshooting section or contact support.

유지

배터리 교체

Replace batteries in both the transmitter and receiver when the low battery indicator appears on the transmitter's LCD, or if the remote control range decreases significantly. Use high-quality alkaline batteries for optimal performance.

• 송신기: AAA 배터리 2개.
• 수화기: AA 배터리 4개.

Always replace all batteries at the same time. Dispose of old batteries responsibly according to local regulations.

청소

Wipe the transmitter and receiver with a soft, dry cloth. Do not use abrasive cleaners or immerse the units in water.

문제 해결

명세서

• 모델: 9800325 (SKY-3301P2)
• 상표: 스카이테크
• 제품 크기: 6.5 x 3.6 x 3 inches (Transmitter and Receiver combined, approximate)
• 무게: 12.96온스(대략)
• 송신기 전력: AAA 배터리 2개
• 수신기 전력: AA 배터리 4개
• 제어 유형: 푸시 버튼
• 특징: Programmable Thermostat, Backlit Display
• 무선 범위: 최대 20피트(무지향성 RF)
• 보안 코드: 1,048,567개의 고유 코드
• 특정 용도: Fireplace Control, Thermostat Control, Indoor Residential Environments

보증 및 지원

For warranty information or technical support, please refer to the documentation included with your purchase or visit the official SkyTech web사이트. 보증 청구를 위해 구매 증빙 자료를 보관하세요.

제조업체: 스카이텍

For further assistance, contact SkyTech customer service.