1. 서론
The OSRAM eldoLED Optotronic LED Driver OT Programmer is a specialized tool designed for programming single, non-DALI OPTOTRONIC LED drivers. This device facilitates quick and efficient configuration of LED drivers using the Tuner4TRONIC software via a standard USB interface. It allows for programming without the need to apply mains voltage to the driver, streamlining the setup process for professional lighting installations.
This manual provides essential information for the safe and effective use of your OT Programmer, including setup, operation, maintenance, and technical specifications.
Image 1.1: eldoLED Optotronic OT Programmer with a connected programming cable, showing the USB and programming ports.
2. 안전 정보
기기를 작동하기 전에 모든 안전 지침을 읽고 숙지하십시오. 이 지침을 따르지 않을 경우 감전, 화재 또는 심각한 부상을 입을 수 있습니다.
- 자격을 갖춘 전문가만: This device is intended to be used by qualified professionals only.
- 지침을 읽어보세요: Always read the complete installation and operating instructions before use.
- No AC Connection: Do not connect the OT Programmer to an AC (mains) line. The unit is powered exclusively through its USB port.
- 작동 온도: Ensure the ambient temperature range is between 0°C and +50°C (32°F to 122°F) during operation.
- 호환성: This programmer is suitable only for non-DALI OPTOTRONIC devices that utilize the Prog +/- interface.
The device complies with FCC 47 CFR part 15, Class A, IEC 60950-1, and IEC 55022 standards.
3. 설정
Follow these steps to set up your OT Programmer for use:
3.1. 소프트웨어 설치
The OT Programmer requires the Tuner4TRONIC software for operation. This software is essential for configuring your LED drivers.
- 소프트웨어 다운로드: Obtain the latest version of the Tuner4TRONIC software from the official eldoLED web대지. 방문 www.eldoLED.com/contact for download links and support.
- 소프트웨어 설치: Follow the on-screen instructions to install Tuner4TRONIC on your computer.
3.2. 프로그래머 연결
The OT Programmer is powered and communicates via a standard USB connection.
- 컴퓨터에 연결: Use a standard USB cable to connect the OT Programmer to an available USB 2.0 port on your computer. The unit will power on automatically.
- Connect to LED Driver: Connect the programming cable from the OT Programmer's "Program (+)/(-)" interface to the corresponding Prog +/- interface on the non-DALI OPTOTRONIC LED driver you wish to program.
이미지 3.1: 상단 view of the eldoLED Optotronic OT Programmer, highlighting the USB 2.0 port and the Program (+)/(-) interface.
4. 사용 설명서
Once the hardware is connected and the Tuner4TRONIC software is installed, you can proceed with programming your LED drivers.
- Launch Tuner4TRONIC: Open the Tuner4TRONIC software on your computer.
- 장치 인식: The software should automatically detect the connected OT Programmer and the LED driver. If not, check your connections and ensure the software is up to date.
- Configure Driver: Use the Tuner4TRONIC interface to select the desired parameters and settings for your OPTOTRONIC LED driver.
- Program Driver: Initiate the programming process through the software. The OT Programmer will transfer the settings to the LED driver. This process is typically very fast.
- 설정 확인: After programming, it is recommended to verify the settings within the Tuner4TRONIC software to ensure successful configuration.
5. 유지관리
The OT Programmer is designed for durability and requires minimal maintenance.
- 청소: 기기를 깨끗하게 유지하고 먼지가 쌓이지 않도록 하십시오. 부드럽고 마른 천으로 닦으십시오. 액체 세척제나 용제를 사용하지 마십시오.
- 저장: Store the programmer in a dry, cool environment when not in use.
- 케이블 관리: Handle USB and programming cables with care to prevent damage to connectors and wires.
6. 문제 해결
If you encounter issues with your OT Programmer, refer to the following common troubleshooting steps:
- 프로그래머가 인식되지 않음:
- Ensure the USB cable is securely connected to both the programmer and the computer.
- 컴퓨터의 다른 USB 포트를 사용해 보십시오.
- Verify that the Tuner4TRONIC software is correctly installed and up to date.
- 컴퓨터를 다시 시작하세요.
- LED Driver Not Detected:
- Confirm that the programming cable is correctly connected to the Prog +/- interface of the LED driver.
- Ensure the LED driver is a compatible non-DALI OPTOTRONIC device with the Prog +/- interface.
- Check for any physical damage to the programming cable or the driver's interface.
- 프로그래밍 오류:
- Refer to the Tuner4TRONIC software documentation for specific error codes and solutions.
- Ensure the LED driver is in a ready state for programming.
For persistent issues, contact customer support as detailed in Section 8.
7. 사양
| 특징 | 사양 |
|---|---|
| 모델 번호 | 4052899209640 |
| 부품 번호 | 4052899209640 |
| 공칭 권tage | 5.00 V (USB powered) |
| 주전원 주파수 | 0 Hz (Not connected to AC) |
| 제품 크기(L x W x H) | 4.7 x 3 x 1.1인치(119.4 x 76.2 x 27.9mm) |
| 제품 무게 | 4 온스(113.4그램) |
| 주변 온도 범위 | 0°C ~ +50°C(32°F ~ 122°F) |
| 재료 | 구리(내부 구성 요소) |
| 인터페이스 | USB 2.0, Prog +/- |
| 호환성 | Non-DALI OPTOTRONIC devices with Prog +/- interface |
| 필수 소프트웨어 | Tuner4TRONIC |
8. 보증 및 지원
For warranty information and technical support, please refer to the official OSRAM or eldoLED website. You can typically find detailed warranty terms and contact information for support services at www.eldoLED.com/contact or through your local OSRAM/eldoLED distributor.
지원팀에 문의할 때는 제품 모델 번호(4052899209640)와 관련 구매 정보를 준비해 주세요.
