Delock 86108 Network Cable Tester User Manual

소개

This manual provides detailed instructions for the safe and efficient operation of your Delock 86108 Network Cable Tester. This device is designed to test various cable types, including RJ45, RJ12, BNC, and USB, for continuity and correct wiring, ensuring reliable network and data connections.

안전 지침

• 기기를 사용하기 전에 모든 지침을 자세히 읽으세요.
• Do not expose the device to moisture, liquids, or extreme temperatures.
• Use only the specified 9V battery type. Incorrect battery usage may damage the device.
• 기기를 직접 열거나 수리하지 마십시오. 모든 정비는 자격을 갖춘 기술자에게 맡기십시오.
• 기기를 어린이의 손이 닿지 않는 곳에 보관하세요.

패키지 내용

• Delock 86108 Network Cable Tester (Main Unit)
• 원격 장치
• 사용 설명서 (본 문서)

참고: 배터리는 포함되어 있지 않으므로 별도로 구매해야 합니다.

제품 끝view

The Delock 86108 Network Cable Tester consists of a main unit and a detachable remote unit. It features an integrated LED display for indicating test results for various cable types.

본체

Image Description: A red and yellow Delock 86108 Network Cable Tester main unit, showing the various ports (RJ45, RJ12, BNC, USB) and the LED indicator panel. The device has a robust, handheld design.

원격 장치

The remote unit detaches from the main unit, allowing for convenient testing of installed cables over longer distances. It typically features corresponding ports to connect the opposite end of the cable being tested.

설정

배터리 설치

1. 본체 뒷면에 있는 배터리 칸을 찾으세요.
2. 배터리 덮개를 엽니다.
3. Insert one 9V battery, ensuring correct polarity (+/-) as indicated inside the compartment.
4. 배터리 덮개를 단단히 닫으세요.

전원 켜기/끄기

To power on the device, slide the power switch to the "ON" position. The LED indicators will briefly illuminate as a self-test. To power off, slide the switch to the "OFF" position.

작동 지침

The Delock 86108 can test various cable types for continuity and correct wiring sequence. Always ensure the tester is powered on before connecting cables for testing.

Testing RJ45/RJ12 Cables

1. Connect one end of the RJ45 or RJ12 cable to the corresponding port on the main unit.
2. Connect the other end of the cable to the corresponding port on the remote unit. For installed cables, the remote unit can be detached and placed at the other end of the cable run.
3. 테스터를 켜십시오.
4. Observe the LED indicators on both the main and remote units. Each LED corresponds to a specific wire. A sequential illumination of LEDs (1-8 for RJ45, 1-6 for RJ12) on both units indicates correct wiring and continuity.
5. If an LED does not light up, it indicates an open circuit (broken wire).
6. If LEDs light up out of sequence, it indicates a wiring fault (e.g., crossed pairs, short circuit).

Testing BNC Cables

1. Connect one end of the BNC cable to the BNC port on the main unit.
2. Connect the other end of the BNC cable to the BNC port on the remote unit.
3. 테스터를 켜십시오.
4. The LED indicators will show continuity for the center conductor and the shield.

Testing USB Cables

1. Connect one end of the USB cable (Type A or B, depending on the tester's ports) to the main unit.
2. Connect the other end to the remote unit.
3. 테스터를 켜십시오.
4. The LEDs will indicate continuity for the power, data+, data-, and ground lines of the USB cable.

유지

청소

Wipe the device with a soft, dry, lint-free cloth. Do not use abrasive cleaners, solvents, or harsh chemicals, as these can damage the casing 또는 내부 구성 요소.

저장

Store the device in a cool, dry place, away from direct sunlight and extreme temperatures. If the device will not be used for an extended period, remove the battery to prevent potential leakage and damage.

문제 해결

장치의 전원이 켜지지 않습니다.

• Check if the 9V battery is correctly installed with the proper polarity.
• Ensure the battery has sufficient charge. Replace with a new 9V battery if necessary.
• Verify the power switch is firmly in the "ON" position.

LEDs do not light up or show inconsistent patterns.

• Ensure all cables are securely connected to both the main and remote units. Loose connections can cause false readings.
• Inspect the cable being tested for visible damage, kinks, or frayed connectors.
• Test with a known good cable to verify the tester's functionality. If the known good cable tests correctly, the issue lies with the original cable.
• Replace the battery if the LEDs appear dim, flicker, or behave erratically, indicating low power.

명세서

• 모델: 델록 86108
• 지원되는 커넥터: BNC, RJ-12, RJ-45, USB
• 디스플레이 유형: LED 표시등
• 전원: 1 x 9V 배터리(포함되지 않음)
• 치수(길이 x 너비 x 높이): 185mm x 80mm x 32mm(7.28인치 x 3.15인치 x 1.26인치)
• 무게: 470그램(16.58온스)
• 제품 색상: 빨간색, 노란색

보증 및 지원

For detailed warranty information, technical support, or service inquiries, please refer to the documentation provided with your original purchase or contact your authorized retailer. Please retain your proof of purchase for any warranty claims.