로우랜스 NAC-2 자동 조종 컴퓨터 사용 설명서

1. 서론

The Lowrance NAC-2 autopilot computer is a core component of a marine autopilot system, designed to provide reliable and precise vessel control. This low-current unit is specifically engineered for smaller vessels, supporting hydraulic and mechanical drives for boats up to 10 meters (33 feet) in length. It also features a solenoid output for compatible steering systems.

This manual provides essential information for the proper installation, operation, and maintenance of your NAC-2 autopilot computer, ensuring optimal performance and longevity.

2. 설정 및 설치

Proper installation is crucial for the performance and safety of your autopilot system. It is highly recommended that installation be performed by a qualified marine electronics technician.

2.1 설치 위치

• Mount the NAC-2 in a dry, protected location, away from direct sunlight, excessive heat, and moisture.
• 과열을 방지하기 위해 장치 주변에 적절한 환기를 확보하세요.
• Mount securely using the provided hardware, ensuring the unit is stable and free from vibration.

2.2 배선 및 연결

The NAC-2 features dedicated ports for power, drive, feedback, and network connections. Refer to the diagram below for port identification.

그림 1: Lowrance NAC-2 Autopilot Computer showing the top view with "NAC-2 AUTOPILOT COMPUTER" label, and the side view with connection ports labeled "POWER", "DRIVE", "FEEDBACK", and "NETWORK". Mounting holes with screws are visible at the base.

• 힘: Connect to a stable 12V DC power source, ensuring proper fusing and wire gauge for the expected current draw.
• 운전하다: Connects to the hydraulic pump or mechanical drive unit. Ensure correct polarity and secure connections.
• 피드백: Connects to the rudder feedback unit, which provides information on the rudder's position to the autopilot computer.
• 회로망: Connects to the NMEA 2000 network for communication with other marine electronics, such as chartplotters, displays, and sensors.

Always consult the detailed wiring diagrams provided in the full installation guide for your specific vessel and system configuration.

3. Operating the Autopilot System

The NAC-2 autopilot computer functions as the brain of your autopilot system, processing data from various sensors and controlling the steering mechanism. Operation is typically managed through a compatible autopilot controller or a multi-function display (MFD) connected via the NMEA 2000 network.

3.1 시스템 교정

After installation, the autopilot system must be calibrated. This process typically involves:

• 나침반 보정: Swinging the vessel to allow the compass to learn its deviation.
• Rudder Calibration: Learning the full range of rudder movement.
• Dockside & Sea Trial Calibration: Fine-tuning performance parameters for optimal steering response in various sea conditions.

Refer to your autopilot controller or MFD manual for detailed calibration procedures.

3.2 Autopilot Modes

Common operating modes include:

• 자동 모드 : Maintains a set course.
• No Drift Mode: Compensates for wind and current to maintain a ground track.
• 탐색 모드: Steers the vessel along a pre-programmed route from a chartplotter.
• 대기 모드: Disengages the autopilot, allowing manual steering.

4. 유지관리

The Lowrance NAC-2 autopilot computer is designed for durability and requires minimal routine maintenance. However, periodic checks can help ensure its long-term reliability.

• 시각적 검사: Periodically inspect the unit and its connections for any signs of corrosion, loose wires, or physical damage.
• 청소: 부드러운 천으로 기기를 닦으십시오. damp cloth. Do not use harsh chemicals or abrasive cleaners. Ensure all ports are free of debris.
• 소프트웨어 업데이트: 로우랜스를 확인해 보세요 website periodically for firmware updates for the NAC-2 and your connected devices. Keeping software up-to-date can improve performance and add new features.
• 연결 무결성: Ensure all network and power cables are securely fastened and free from strain.

5. 문제 해결

This section provides basic troubleshooting steps for common issues. For more complex problems, contact Lowrance customer support or a certified marine electronics technician.

6. 사양