1. 서론
The Lascar Electronics EL-21CFR-TP-LCD EasyLog 21CFR FDA-Compatible Temperature Data Logger with Probe is a standalone device designed for accurate temperature monitoring. This data logger is compliant with 21CFR regulations and is capable of recording and displaying over 32,000 temperature readings from its high-accuracy thermistor probe. It features an integrated LCD screen and a push-button interface, allowing users to easily view the most recent, highest, and lowest recorded temperature values.
2. 안전 정보
Please read all instructions carefully before operating the device. Failure to do so may result in inaccurate readings or damage to the unit.
- Do not expose the data logger to extreme temperatures outside its specified operating range (-35 to +80°C / -31 to +176°F).
- Avoid exposing the device to excessive moisture or corrosive substances.
- Handle the thermistor probe with care to prevent damage.
- 밀폐된 공간에서 사용할 경우 적절한 환기가 이루어지도록 하십시오.
- 장치를 분해하거나 개조하지 마십시오. 모든 정비는 자격을 갖춘 기술자에게 맡기십시오.
- 해당 기기와 구성품은 지역 환경 규정에 따라 폐기하십시오.
3. 제품 오버view
The EL-21CFR-TP-LCD data logger is a compact and robust device designed for reliable temperature monitoring.
Figure 1: Lascar Electronics EL-21CFR-TP-LCD Data Logger. The image shows the black data logger unit with an LCD display showing "12.0°C", a button, and a USB connector at one end. A clear protective cap is shown detached from the USB end.
주요 구성 요소:
- LCD 디스플레이: Shows current temperature, highest, lowest, and other status indicators.
- 누름 단추: Used to cycle through display modes and initiate logging (if configured).
- USB 커넥터: For connecting to a computer to configure the logger and download data.
- Thermistor Probe Input: Port for connecting the external thermistor probe.
- 보호 캡: 사용하지 않을 때는 USB 커넥터를 덮어줍니다.
4. 설정
4.1 소프트웨어 설치
Before using the data logger, you must install the EasyLog 21CFR software on your computer. This software is required for configuring the logger, downloading data, and view그래프를 그리다.
- Obtain the EasyLog 21CFR software from the manufacturer's official web사이트 또는 제공된 설치 미디어를 참조하세요.
- 화면의 지시에 따라 소프트웨어 설치를 완료하십시오.
- 컴퓨터가 소프트웨어의 최소 시스템 요구 사항을 충족하는지 확인하십시오.
4.2 초기 구성
Once the software is installed, connect the data logger to your computer via the USB port.
- Remove the protective cap from the USB connector of the data logger.
- Plug the data logger into an available USB port on your computer.
- Launch the EasyLog 21CFR software. The software should detect the connected data logger.
- Within the software, configure the desired logging parameters, including:
- Logging rate (e.g., every 10 minutes, every hour)
- Start mode (e.g., immediate, delayed start, push-button start)
- 경보 임계값(고온 및 저온 한계)
- Units of measurement (°C or °F)
- Apply the settings to the data logger. The logger is now ready for deployment.
4.3 프로브 연결
Connect the thermistor probe to the designated input port on the data logger. Ensure a secure connection for accurate readings.
5. 운영
5.1 데이터 로깅 시작
The method for starting data logging depends on the configuration set in the software:
- 즉시 시작: Logging begins as soon as the settings are applied from the software.
- 지연된 시작: Logging begins after a pre-set time delay.
- 푸시 버튼 시작: Press and hold the push-button on the data logger for approximately 3 seconds until the 'REC' indicator appears on the LCD.
5.2 Viewing Readings on LCD
Press the push-button briefly to cycle through the displayed information on the LCD:
- 현재 온도: The real-time temperature reading from the probe.
- Highest Recorded Temperature: The maximum temperature recorded during the current logging session.
- Lowest Recorded Temperature: The minimum temperature recorded during the current logging session.
- 로깅 상태: Indicators such as 'REC' (recording), 'STOP' (stopped), 'FULL' (memory full).
5.3 데이터 로깅 중지
Logging can be stopped in several ways, depending on the configuration:
- 메모리 용량 부족: Logging automatically stops when the device's memory capacity (32,000 readings) is reached.
- Push-Button Stop: If configured, press and hold the push-button for approximately 3 seconds until the 'STOP' indicator appears.
- 소프트웨어를 통해: Connect the logger to a computer and use the EasyLog 21CFR software to stop the logging session.
5.4 데이터 다운로드
기록된 데이터를 검색하려면:
- 데이터 로거를 USB 케이블로 컴퓨터에 연결하세요.
- Open the EasyLog 21CFR software.
- The software will automatically detect the logger and prompt you to download the data.
- Follow the software instructions to save the data, which can then be viewed, analyzed, and exported in various formats.
6. 유지관리
6.1 청소
데이터 로거의 외부를 부드러운 천으로 닦으십시오.amp cloth. Do not use abrasive cleaners or solvents. Ensure the USB port and probe input are free from dust and debris.
6.2 배터리 교체
The data logger contains an internal battery. If the battery indicator on the LCD or software shows low power, the battery may need replacement. Refer to the EasyLog 21CFR software documentation or contact customer support for battery replacement procedures, as this may require specialized tools or service.
6.3 교정
For applications requiring high accuracy and compliance, periodic calibration of the data logger and its probe is recommended. Consult the manufacturer's guidelines or a certified calibration service for details.
7. 문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 소프트웨어에서 장치가 감지되지 않았습니다. | USB 연결 문제, 소프트웨어 실행 오류, 드라이버 문제. | Ensure USB cable is securely connected. Restart software and computer. Reinstall USB drivers if necessary. Try a different USB port. |
| LCD 화면이 꺼져 있거나 흐릿합니다. | Low battery, device not active. | Connect to USB to check if it powers on. If persistent, battery may need replacement. |
| 온도 판독값이 부정확합니다. | Probe not properly connected, probe damage, environmental interference, calibration needed. | Check probe connection. Inspect probe for visible damage. Ensure probe is placed in a representative environment. Consider recalibration. |
| 데이터 로깅이 시작되지 않습니다. | Incorrect start mode configuration, memory full. | Verify start mode settings in software. Check if memory is full; download data and reconfigure. |
8. 사양
| 특징 | 세부 사항 |
|---|---|
| 모델 번호 | EL-21CFR-TP-LCD+ |
| 측정 범위 | -35 ~ + 80 ° C / -31 ~ + 176 ° F |
| 메모리 용량 | 32,000개의 온도 판독값 |
| 프로브 유형 | Thermistor probe |
| 표시하다 | LCD with current, highest, and lowest readings |
| 인터페이스 | USB |
| 규정 준수 | 21CFR |
| 품목 무게 | 1 파운드 |
| 제조업체 | 콜-파머 |
| 첫 번째 가능한 날짜 | 20년 2017월 XNUMX일 |
9. 보증 및 지원
Specific warranty information for the Lascar Electronics EL-21CFR-TP-LCD data logger is typically provided with the product packaging or available on the manufacturer's official website. Please refer to these resources for detailed terms and conditions regarding warranty coverage.
고객 지원:
For technical assistance, troubleshooting beyond this manual, or inquiries regarding service and calibration, please contact Lascar Electronics customer support. Contact details can usually be found on their official web사이트 또는 제품 설명서에서.
