제품 끝view
The Greenheck 360100 Dodge Bearing, model 055106, is a genuine OEM replacement part designed for various industrial applications. This bearing is critical for ensuring smooth and efficient operation of machinery by reducing friction between moving parts. Manufactured by Greenheck, a leading supplier of air movement and control equipment, this component is engineered for safety, reliability, and performance.
영상: A Greenheck 360100 Dodge Bearing, model 055106, shown in a dark green housing with a silver bearing insert. The housing features two mounting holes and a grease fitting on top. The bearing itself has "DODGE" and "USA" markings. This image illustrates the complete bearing assembly.
설정 및 설치
Proper installation of the Dodge Bearing is crucial for its longevity and optimal performance. It is recommended that installation be performed by qualified personnel following standard industrial practices and equipment-specific guidelines.
- 준비: Ensure the mounting surface is clean, flat, and free from burrs or debris. Verify that the shaft is clean and within specified tolerances.
- 설치: Securely fasten the bearing housing to the equipment using appropriate bolts and torque specifications. Ensure proper alignment with the shaft to prevent premature wear and vibration.
- 매끄럽게 하기: Before initial operation, lubricate the bearing according to the manufacturer's recommendations. Refer to the maintenance section for lubrication details.
- 샤프트 삽입: Carefully slide the bearing onto the shaft. Avoid forcing the bearing, which can cause damage.
운영 지침
Once installed, the Dodge Bearing is designed for continuous operation within its specified load and speed limits. Observe the following guidelines for optimal performance:
- 초기 길들이기: During the first few hours of operation, monitor the bearing for unusual noise, vibration, or excessive heat.
- 정상 작동: The bearing should operate smoothly with minimal noise and vibration. Slight warmth is normal, but excessive heat indicates a potential issue.
- 부하 및 속도: Do not exceed the maximum load and speed ratings specified for the bearing and the equipment it is installed in.
유지
Regular maintenance is essential to extend the life of your Greenheck Dodge Bearing and ensure reliable operation. Adhere to a consistent maintenance schedule.
- 매끄럽게 하기:
Proper lubrication is critical. Use a high-quality grease recommended for industrial bearings. The frequency of lubrication depends on operating conditions (speed, load, temperature, environment). Consult your equipment's manual or a lubrication guide for specific intervals.
- Apply grease slowly until a slight resistance is felt or a small amount of old grease purges from the seals (if applicable).
- Avoid over-greasing, which can lead to overheating and seal damage.
- 점검:
Periodically inspect the bearing for signs of wear, damage, or contamination.
- 이상한 소음, 진동 또는 과도한 열이 발생하는지 확인하십시오.
- Examine the housing for cracks or damage.
- Inspect seals for integrity and signs of grease leakage or contaminant ingress.
- 청소: Keep the area around the bearing clean to prevent contaminants from entering the bearing and causing premature wear.
문제 해결
If you encounter issues with your Dodge Bearing, refer to the following common problems and their potential solutions:
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 과도한 소음 | Lack of lubrication, contamination, misalignment, worn bearing. | Check lubrication, clean, verify alignment, replace bearing if worn. |
| 과열 | Over-lubrication, under-lubrication, misalignment, excessive load, contamination. | Adjust lubrication, verify alignment, reduce load if possible, clean. |
| 진동 | Misalignment, imbalance, loose mounting, worn bearing. | Check and correct alignment, tighten mounting bolts, replace bearing. |
| 조기 고장 | Improper installation, inadequate lubrication, excessive load, contamination, incorrect bearing type. | Review installation procedures, ensure proper lubrication, verify load, maintain cleanliness, ensure correct bearing selection. |
If troubleshooting steps do not resolve the issue, contact Greenheck customer support or a qualified technician.
명세서
Key specifications for the Greenheck 360100 Dodge Bearing:
- 모델 번호: 360100
- 베어링 번호: 55106
- 상표: 그린헥
- 재료: 금속
- 제품 크기(길이 x 너비 x 높이): 9 x 6 x 5 인치
- 품목 무게: 1.6파운드(0.703킬로그램)
- Package Dimensions (H x L x W): 15.6 x 8.1 x 13.9 센티미터
- 원산지: 미국
- 부품 유형: OEM replacement part
보증 정보
Specific warranty terms and conditions for the Greenheck 360100 Dodge Bearing are provided by the manufacturer, Greenheck. Please refer to the documentation included with your purchase or contact Greenheck directly for detailed warranty information. Warranty coverage typically addresses manufacturing defects and material flaws under normal use conditions.
고객 지원
For technical assistance, replacement parts, or any inquiries regarding the Greenheck 360100 Dodge Bearing, please contact Greenheck customer support. You can typically find contact information on the official Greenheck web웹사이트 또는 공인 대리점을 통해 구입하실 수 있습니다.
Note: Always provide the model number (360100) and any relevant serial numbers when contacting support to expedite assistance.
