소개
This manual provides essential instructions for the installation, operation, maintenance, and troubleshooting of your APC Back-UPS Pro 1350VA Uninterruptible Power Supply (UPS). This device is designed to provide battery backup power and surge protection for electronic equipment, ensuring continuous operation during power outages and protection against damaging power fluctuations.
Figure 1: APC Back-UPS Pro 1350VA UPS, angled view.
패키지 내용
패키지에 다음 품목이 포함되어 있는지 확인하십시오.
- APC Back-UPS Pro 1350VA UPS Unit
- 사용 설명서 (본 문서)
- USB 통신 케이블
- 동축 케이블
설정
1. 초기 배터리 연결
The UPS is shipped with the battery disconnected for safety during transit. Before initial use, the internal battery must be connected.
- Place the UPS in its desired location. Ensure adequate ventilation around the unit.
- Refer to the battery compartment access instructions (typically located on the bottom or rear of the unit) to connect the internal battery.
- 배터리 칸을 단단히 닫으세요.
2. 장비 연결
The UPS features two types of outlets: Battery Backup & Surge Protection, and Surge Protection Only.
Figure 2: Rear panel with outlets and communication ports.
- Battery Backup & Surge Protection Outlets (5 outlets): 컴퓨터, 모니터, 외장 하드 드라이브, 네트워크 라우터와 같은 중요 장비를 이 콘센트에 연결하십시오. 정전 시 이러한 장치는 배터리에서 전원을 공급받습니다.tage.
- Surge Protection Only Outlets (5 outlets): Connect non-critical equipment like printers, scanners, or desk lamps to these outlets. These devices are protected from surges but will not receive battery power during an outage.
3. 유틸리티 전원에 연결
Plug the UPS power cord into a grounded 120V AC wall outlet. Avoid using extension cords or surge protectors with the UPS.
4. 초기 충전
Allow the UPS to charge for at least 24 hours before connecting any equipment to ensure maximum battery runtime. The UPS will provide surge protection even if the battery is not fully charged.
5. 데이터 회선 보호
For network dataline protection, connect your network cable from the wall outlet to the 'IN' port on the UPS, and then connect a second network cable from the 'OUT' port to your device (e.g., computer, router). Similarly, use the coaxial cable ports for cable modem or TV protection.
UPS 작동
전면 패널 디스플레이 및 컨트롤
그림 3: LCD 디스플레이와 제어 버튼이 있는 전면 패널.
The front panel features an LCD display and control buttons for monitoring and managing the UPS.
- 전원 버튼: 무정전 전원 공급 장치(UPS)를 켜거나 끕니다.
- 디스플레이 버튼: Cycles through various display screens showing information such as battery charge, estimated runtime, input/output voltage, and load.
- 음소거 버튼: 경보음을 끕니다.
자동 볼륨tage 규정(AVR)
UPS에는 자동 전압 조절 기능이 있습니다.tage Regulation (AVR) to correct minor voltage fluctuations without switching to battery power. This extends battery life by reducing the frequency of battery usage.
PowerChute 소프트웨어
For advanced management and automatic shutdown capabilities, connect the UPS to your computer using the provided USB cable. Download and install the PowerChute software from the APC web사이트. 이 소프트웨어를 사용하면 다음을 수행할 수 있습니다.
- UPS 상태 및 전원 조건을 모니터링합니다.
- Configure automatic, graceful shutdown of your computer during extended power outag에스.
- View energy usage and cost.
For Mac OS, use native "Energy Saver" settings for UPS management.
유지
배터리 교체
The APC Back-UPS Pro 1350VA features a user-replaceable battery (model APCRBC123, sold separately). Batteries typically last 3-5 years depending on usage and environmental conditions. Replace the battery when the UPS indicates a battery fault or when runtime significantly decreases.
- Turn off all connected equipment and the UPS.
- UPS를 벽면 콘센트에서 분리합니다.
- Follow the instructions provided with the replacement battery for safe removal of the old battery and installation of the new one.
- 오래된 배터리는 책임감 있게 재활용하세요.
청소
Periodically clean the exterior of the UPS with a soft, dry cloth. Do not use liquid cleaners or solvents. Ensure ventilation openings are free from dust and debris.
문제 해결
If the UPS is not operating correctly, consult the following table for common issues and solutions.
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| UPS가 켜지지 않습니다. | 배터리가 연결되지 않았거나 충전량이 부족합니다. | 배터리가 연결되어 있는지 확인하십시오. UPS를 벽면 콘센트에 꽂고 24시간 동안 충전하십시오. |
| UPS에서 계속해서 경고음이 울립니다. | On battery power, low battery, or overload | Check utility power. Reduce connected load. Allow battery to charge. |
| "Building Wiring Fault" indicator is lit | Wiring problem in wall outlet | 자격을 갖춘 전기 기술자에게 건물 배선을 점검받으십시오. |
| 짧은 런타임 | Battery is old or not fully charged | Allow battery to charge for 24 hours. Consider replacing the battery if it is old. |
If problems persist after attempting these solutions, contact APC customer support.
명세서
| 특징 | 세부 사항 |
|---|---|
| 모델 번호 | BX1350M |
| 용량 | 1350VA / 810W |
| 입력 Voltage | 120 볼트 |
| 아울렛 | 10개 (배터리 백업 및 서지 보호 기능 5개, 서지 보호 기능만 5개) |
| 배터리 유형 | 밀폐형 납산 배터리(사용자 교체 가능: APCRBC123) |
| Network Dataline Protection | 1GB (XNUMX기가바이트) |
| 전원 코드 길이 | 6 feet (right-angle 3-prong plug NEMA 5-15P) |
| 치수(높이 x 너비 x 깊이) | 19.3 x 13.6 x 9 인치 |
| 무게 | 22.5파운드 |
| 색상 | 검은색 |
| 인증 | 에너지스타 인증 |
보증 및 지원
For information regarding the manufacturer's warranty, please refer to the documentation included with your product or visit the official APC web사이트. 확장된 보호 플랜도 구매 가능할 수 있습니다.
For technical assistance or customer support, please visit the 슈나이더 일렉트릭 APC 스토어 or contact APC customer service directly.
