Sommer Slider+ S10305 TX40-868-4 차고 문 리모컨 사용 설명서

1. 서론

This manual provides comprehensive instructions for the Sommer Slider+ S10305 TX40-868-4 garage door remote control. Designed for use with Sommer Base+ and Pro+ drive systems, this remote offers secure and convenient operation of your garage door. Please read these instructions carefully before use to ensure proper function and safety.

Image 1: Sommer Slider+ S10305 remote control with its protective slider closed.

2. 주요 특징

• Retrocompatible: Works with the Somloq Rollingcode radio system, allowing control of existing drives and wireless receivers.
• 모던한 디자인: High-quality construction with a stainless steel finish.
• 슬라이딩 기능: Features a protective slider to prevent unintentional button presses.
• 컴팩트한 사이즈: Easily attaches to a keychain for portability.
• SOMloq2 Radio System: Offers maximum security against unauthorized access through AES 128-bit encryption with a rolling code.
• Automatic Repeat Function: Enables comfortable opening as you approach the object.
• Enhanced Range & Reliability: Improved performance due to the Hop function, where the signal is actively transmitted by the SOMloq2 receiver.
• Multiple Commands: Supports 4 distinct radio commands.

3. 설정 및 프로그래밍

To program your Sommer Slider+ S10305 remote control with your garage door opener (e.g., Sommer Base+ or Pro+ drive), follow these steps:

1. Locate the Control Unit: Find the control unit of your garage door motor. Open its cover to access the programming button.
2. Identify Programming Button: Identify the programming button, often labeled 'Radio' or similar. It is usually located near a small hole. Use a small, non-conductive object like a toothpick to press this button.
3. 프로그래밍 모드 활성화: A small red indicator light on the control unit will illuminate, indicating it is in programming mode.
4. Position Remote: Take your new Sommer Slider+ remote control. Position it close to the red indicator light on the control unit.
5. Press and Hold Remote Button: Press and hold the button on the remote control that you wish to program for opening/closing the garage door.
6. 프로그래밍 확인: Continue holding the button until the red indicator light on the control unit stops flashing rapidly and then extinguishes. This indicates successful programming.
7. 원격 테스트: Release the button on the remote control. Test the remote by pressing the programmed button. The garage door should now operate.

메모: Ensure your garage door opener is compatible with the SOMloq2 radio system and the 868.8 MHz / 868.95 MHz frequencies. Some regional variations of Sommer products exist; verify compatibility if issues arise.

Image 2: Sommer Slider+ S10305 remote control with the slider open, revealing the four control buttons.

4. 운영

The Sommer Slider+ S10305 remote control features a sliding cover to protect the buttons from accidental presses. To operate your garage door:

1. Slide Down Cover: Gently slide the protective cover down to reveal the control buttons.
2. 버튼을 누르시오: Press the desired, pre-programmed button to activate your garage door opener. Each button can be programmed for a different function or to control a different door.
3. Slide Up Cover: After use, slide the cover back up to protect the buttons and prevent unintended activation.

이미지 3: 앞면 view of the Sommer Slider+ S10305 remote control.

5. 유지보수 및 배터리 교체

The remote control is powered by one CR123A battery. When the remote's range decreases or it stops responding, the battery may need replacement.

배터리 교체:

1. 오픈 Casing: 리모컨을 조심스럽게 열어보세요asing. This typically involves gently prying apart the two halves or removing a small screw if present.
2. 오래된 배터리 제거: Remove the old CR123A battery from its compartment.
3. 새 배터리를 삽입하세요: 새 CR123A 배터리를 넣을 때 극성(+와 -)을 정확히 확인하십시오.
4. C 닫기asing: 리모컨을 닫으세요asin딸깍 소리가 나면서 제자리에 고정될 때까지 단단히 조이십시오.

현지 규정에 따라 오래된 배터리를 책임감 있게 폐기하십시오.

청소:

리모컨은 부드럽고 마른 천으로 닦으십시오. 연마성 세제나 용제를 사용하지 마십시오.

6. 문제 해결

If your Sommer Slider+ S10305 remote control is not functioning as expected, consider the following:

• 리모컨이 응답하지 않음:
  • Check the battery. Replace it with a new CR123A battery if necessary.
  • Ensure the remote is within the operating range (50-140 meters) of the receiver.
  • Verify that the remote is correctly programmed to your garage door opener. Repeat the programming steps if unsure.
• 감소된 범위:
  • 배터리를 교체하세요.
  • Check for sources of interference (e.g., other radio devices, large metal objects, thick walls) near the remote or the receiver.
  • Ensure the antenna on your garage door opener is unobstructed.
• Remote programmed but not working (especially in certain regions):
  • Some Sommer products have regional codes (e.g., S10305-0001 vs. S10305-00075). Ensure the specific model you have is compatible with your region's garage door opener. Incompatible regional codes can prevent proper function.
  • Consult your garage door opener's manual or the manufacturer for regional compatibility information.

7. 기술 사양

8. 보증 및 지원

For warranty information or technical support, please refer to the documentation provided with your original purchase or contact Sommer customer service directly. Keep your proof of purchase for warranty claims.