소개
Thank you for choosing the GoControl WS15Z5-1 Z-Wave Wall Switch. This smart switch allows you to control your lighting or other connected loads remotely via a Z-Wave network, as well as manually. It integrates seamlessly into your smart home system, providing convenience and energy efficiency. Please read this manual carefully before installation and operation to ensure proper use and safety.
안전 정보
경고: Risk of Electric Shock. Installation should be performed by a qualified electrician. Disconnect power at the circuit breaker or fuse box before installation or servicing. Use only copper wire for connections. Do not exceed the maximum load ratings.
- 설치하기 전에 회로 차단기에서 전원이 꺼져 있는지 확인하십시오.
- 이 장치는 National Electric Code 및 현지 규정에 따라 설치하도록 되어 있습니다.
- 습한 곳이나 물에 직접 노출된 곳에서는 사용하지 마십시오.
- 실내에서만 사용하세요.
패키지 내용
- GoControl WS15Z5-1 Z-Wave Wall Switch
- 설치 나사
- 와이어 너트 (포장에 따라 구성품이 다를 수 있습니다)
- 사용 설명서 (본 문서)
설정 및 설치
Follow these steps carefully to install your GoControl Z-Wave Wall Switch.
1. Wiring the Switch
- 전원을 끄세요: Locate the circuit breaker controlling the switch you are replacing and turn it OFF. Verify power is off by attempting to turn on the light or appliance.
- 이전 스위치 제거: Carefully remove the existing wall plate and switch from the wall box. Disconnect the wires from the old switch, noting which wire was connected to which terminal (Line, Load, Neutral, Ground).
- 전선 식별:
- (핫라인): 보통 검은색이며, 차단기에서 나오는 빛입니다.
- 짐: Usually black, going to the light fixture or appliance.
- 중립적: Usually white, often bundled together in the back of the box. (Required for Z-Wave switches).
- 지면: 일반적으로 녹색이거나 구리색을 띕니다.
- 새로운 스위치 연결: Connect the wires to the GoControl WS15Z5-1 switch terminals as follows:
- 연결하다 선 wire to the terminal marked "LINE".
- 연결하다 짐 wire to the terminal marked "LOAD".
- 연결하다 중립적 wire to the terminal marked "NEUTRAL".
- 연결하다 지면 wire to the terminal marked "GROUND".
Ensure all connections are secure. If you are unsure about wiring, consult a qualified electrician.
- 마운트 스위치: 유선 스위치를 벽면 박스에 조심스럽게 밀어 넣으세요. 제공된 나사를 사용하여 고정하세요.
- 벽면 플레이트 설치: 새 벽면판이나 기존 벽면판을 부착합니다.
- 복원력 : 회로 차단기에서 전원을 다시 켜세요.
그림 1: 전면 view of the GoControl WS15Z5-1 Z-Wave Wall Switch.
2. Z-Wave 통합(페어링)
To integrate the switch into your Z-Wave network, you need to "include" it with your Z-Wave controller.
- Put your Z-Wave controller into Inclusion/Pairing mode. (Refer to your Z-Wave controller's manual for specific instructions).
- On the GoControl WS15Z5-1 switch, quickly press the top or bottom paddle 한 번. The LED indicator on the switch will blink to confirm inclusion mode.
- The controller will confirm successful inclusion. The switch's LED will stop blinking and remain solid or turn off, depending on its status.
- If inclusion fails, refer to the Troubleshooting section or try "Exclusion" first.
Figure 2: The Z-Wave logo, indicating compatibility with Z-Wave networks.
스위치 조작
수동 제어
- 를 누르세요 맨 위 of the paddle to turn the connected load ON.
- 를 누르세요 맨 아래 of the paddle to turn the connected load 끄다.
Z파 제어
Once included in your Z-Wave network, you can control the switch remotely using your Z-Wave controller, hub, or compatible smart home application.
- Use your Z-Wave app or controller interface to toggle the switch ON/OFF.
- The switch supports standard Z-Wave commands for basic on/off functionality.
Figure 3: GoControl products integrate with smart home systems for control via smartphones and other devices.
Figure 4: Diagram illustrating GoControl's integration across various smart home categories like Climate, Lighting, Security, Sensors, and Access.
유지
The GoControl WS15Z5-1 Z-Wave Wall Switch requires minimal maintenance.
- 청소: 스위치를 청소하려면 부드러운 천으로 닦으세요.amp 천. 연마성 세척제나 용매를 사용하지 마십시오.
- 펌웨어 업데이트: Check the GoControl website or your Z-Wave controller's documentation for information on potential firmware updates.
- 일반 관리 : 스위치가 과도한 습기나 극한 온도에 노출되지 않도록 주의하세요.
문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| Switch does not respond to manual press. | 스위치에 전원이 공급되지 않음; 배선 오류; 스위치 고장. | Check circuit breaker. Verify wiring connections (Line, Load, Neutral, Ground). If issues persist, contact support. |
| 스위치가 Z-Wave 명령에 응답하지 않습니다. | Not properly included in Z-Wave network; out of range; network interference. | Perform Z-Wave exclusion, then re-inclusion. Move controller closer to the switch during inclusion. Check for other Z-Wave devices interfering. |
| Cannot include switch into Z-Wave network. | Switch is already included in another network; controller not in inclusion mode. | Perform Z-Wave exclusion first (see below). Ensure your controller is in inclusion mode. |
| LED 표시등이 예상대로 작동하지 않습니다. | Indicates network status or error. | Refer to your Z-Wave controller's manual for specific LED behavior interpretations or contact GoControl support. |
Z-Wave Exclusion (Removing from Network)
If you need to remove the switch from your Z-Wave network, follow these steps:
- Put your Z-Wave controller into Exclusion mode. (Refer to your Z-Wave controller's manual for specific instructions).
- On the GoControl WS15Z5-1 switch, quickly press the top or bottom paddle 한 번. The LED indicator will blink to confirm exclusion mode.
- The controller will confirm successful exclusion. The switch's LED will stop blinking.
명세서
| 모델 번호 | WS15Z5-1 (RA45130) |
| 상표 | 고컨트롤 |
| 작동 모드 | 온-오프 |
| 연결 프로토콜 | 지웨이브 |
| 장착 유형 | 벽걸이형 |
| 국제 보호 등급 | IP54 |
| 품목 치수(L x W x H) | 25 x 25 x 25 Millimeters (approx. 1 x 1 x 1 Inches) |
| 품목 무게 | 91g |
| 배터리가 포함되어 있나요? | 아니요 |
보증 및 지원
GoControl products are designed for reliability and performance. For warranty information, technical support, or further assistance, please visit the official GoControl web사이트 또는 고객 서비스 부서에 문의하십시오.
Web대지: www.gocontrol.com
제조업체: GOCONTROL
