소개
This manual provides essential information for the proper setup, operation, and maintenance of your TELECO MIO-868-A04 remote control.
The TELECO MIO-868-A04 is a high-quality remote control designed for gate automation systems, operating at a frequency of 868 MHz. It features a robust design and simple operation, making it an ideal solution for controlling compatible gate receivers.
Image: The TELECO MIO-868-A04 remote control, featuring a black and silver casing with four black buttons.
주요 특징
- Gate remote control with a frequency of 868 MHz.
- Programming type: Recording directly into the receiver unit.
- CR2032 배터리를 사용합니다.
- 컴팩트한 크기: 0.6 x 0.4 x 0.1 cm.
- Equipped with 4 control buttons.
- Maximum operating range of 10 metres.
설정 및 프로그래밍
배터리 설치
The remote control comes with a CR2032 battery pre-installed. If replacement is needed, follow these steps:
- 리모컨 뒷면에서 배터리함을 찾으세요.
- Carefully open the compartment using a small screwdriver or coin.
- 기존 CR2032 배터리를 제거하세요.
- 새로운 CR2032 배터리를 양극(+)이 위를 향하도록 삽입합니다.
- 배터리 칸을 단단히 닫으세요.
원격 제어 프로그래밍
The TELECO MIO-868-A04 remote control is programmed by 'recording' it directly into your gate receiver unit. The exact procedure may vary depending on your specific gate receiver model. Please refer to your gate receiver's instruction manual for detailed programming steps. Generally, the process involves:
- Accessing the programming mode on your gate receiver (often by pressing a 'Learn' or 'Prog' button).
- Pressing a button on the new TELECO remote control when the receiver is in programming mode.
- Confirming successful programming (e.g., an LED indicator on the receiver changes or flashes).
Important: Ensure your gate receiver is compatible with 868 MHz frequency remotes.
작동 지침
Once programmed, the TELECO MIO-868-A04 remote control is ready for use.
- Opening/Closing Gate: Press the assigned button on the remote control to activate your gate. The remote has 4 buttons, allowing for multiple functions if supported by your receiver (e.g., full open, pedestrian open, stop).
- 범위: The maximum effective operating range is approximately 10 metres. Ensure there are no significant obstructions between the remote and the receiver.
- 표시등: A small LED indicator on the remote may illuminate when a button is pressed, indicating battery function and signal transmission.
유지
청소
리모컨은 부드럽고 마른 천으로 닦으십시오. 연마성 세제나 용제를 사용하지 마십시오. 리모컨이 손상될 수 있습니다.asing 및 내부 구성 요소.
배터리 교체
Replace the CR2032 battery when the remote's range decreases significantly or the indicator light fails to illuminate consistently upon button press. Refer to the 'Battery Installation' section for instructions.
저장
Store the remote control in a dry place, away from extreme temperatures and direct sunlight. Avoid dropping the remote or exposing it to water.
문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 리모컨이 작동하지 않습니다 | Dead battery; Not programmed; Out of range; Receiver issue. | Replace battery; Re-program remote (see Setup); Move closer to receiver; Check receiver power/status. |
| 짧은 작동 범위 | Low battery; Interference; Obstructions. | Replace battery; Check for sources of interference (e.g., other wireless devices); Clear line of sight to receiver. |
| LED on remote not lighting up | Dead battery; Faulty remote. | Replace battery; If problem persists, contact support. |
기술 사양
| 모델명 | MIO-868-A04 |
| 상표 | Teleco |
| 빈도 | 868MHz |
| 버튼의 수 | 4 |
| 배터리 유형 | CR2032 |
| 제품 치수 | 0.6 x 0.4 x 0.1cm |
| 무게 | 50g |
| 최대 범위 | 10 미터 |
| 색상 | 블랙 앤 실버 |
보증 및 지원
For specific warranty information, please refer to the documentation provided at the time of purchase or contact your retailer. Standard return policies typically allow for returns within 30 days of purchase, subject to retailer terms and conditions.
For technical support or further assistance with programming, it is recommended to contact the manufacturer, Teleco, or your authorized dealer. Ensure you have your model number (MIO-868-A04) ready when seeking support.
