소개
This manual provides essential instructions for the safe installation, operation, and maintenance of your APC Smart-UPS SRT 10KVA Rackmount Uninterruptible Power Supply (UPS) system, model SRT10KRMXLT-5KTF2. This system includes two 208V to 120V 2U 5KVA Step-Down Transformers. Please read this manual thoroughly before installing or operating the equipment.
중요 안전 지침
본 설명서의 모든 경고 및 작동 지침을 준수하십시오. 그렇지 않을 경우 부상이나 장비 손상이 발생할 수 있습니다.
- This UPS contains internal batteries and may present a shock hazard even when disconnected from the AC power source.
- 배터리 서비스는 배터리 및 필요한 예방 조치에 대해 잘 아는 사람이 수행하거나 감독해야 합니다.
- 배터리를 불 속에 버리지 마십시오. 배터리가 폭발할 수 있습니다.
- 배터리를 열거나 훼손하지 마십시오. 방출된 전해질은 피부와 눈에 해롭습니다. 독성이 있을 수 있습니다.
- 배터리는 감전 및 높은 단락 전류의 위험을 초래할 수 있습니다.
- Refer to local codes for all wiring.
설정 및 설치
1. 개봉 및 검사
Carefully unpack the UPS system and its components. Inspect for any shipping damage. Report any damage to the carrier and your dealer. Retain the packaging materials for future use.
2. 물리적 설치
The APC Smart-UPS SRT 10KVA system supports both rack mount and tower configurations. Ensure adequate ventilation around the unit.
- 랙 마운트: Secure the UPS and step-down transformers into a standard 19-inch equipment rack using the provided mounting hardware. Ensure proper weight distribution.
- 탑: If installing in a tower configuration, use the supplied tower stands to ensure stability.
그림 1: APC Smart-UPS SRT 10KVA Rackmount System. This image displays the APC Smart-UPS SRT 10KVA system, configured for rack mounting. It includes the main UPS unit with its front panel display, and additional rack-mountable components, likely battery packs or step-down transformers, all featuring a black mesh design and the APC logo.
3. 전기 연결
Connect the UPS to a dedicated electrical circuit. Ensure the input voltage matches the UPS requirements (208V nominal). Connect your equipment to the output receptacles of the UPS and the 208V to 120V step-down transformers as needed.
- 입력 전력: Connect the UPS input power cord to a properly grounded 208V AC outlet.
- 출력 전력: Connect critical equipment to the UPS output receptacles. For 120V loads, connect them to the output receptacles of the 208V to 120V 5KVA Step-Down Transformers.
- 배터리 연결: Ensure all internal and external battery connections are secure.
4. 초기 파워업
After all connections are made, press the power button on the front panel to turn on the UPS. The UPS will perform a self-test and then enter online mode.
작업
1. Front Panel Display (LCD)
The LCD display provides real-time information about the UPS status, load, battery charge, and various settings. Use the navigation buttons (ESC, OK, Up, Down) to browse menus and adjust settings.
- 상태 화면: Displays current output voltage, 로드 퍼센트tage, battery status, and operational mode (Online, On Battery, Bypass).
- 구성 메뉴: 출력 볼륨과 같은 설정을 조정할 수 있습니다.tage, alarm thresholds, and network parameters.
2. 기본 동작
- 켜기: 전원 버튼이 화면에 불이 들어올 때까지 길게 누르세요.
- 끄기: Press and hold the power button until the UPS initiates shutdown.
3. Understanding Status Indicators
The UPS uses various indicators (LEDs and LCD messages) to communicate its operational status and any potential issues. Refer to the troubleshooting section for specific error codes.
유지
1. 배터리 교체
The UPS batteries are user-replaceable. Replace batteries when indicated by the UPS or after their service life (typically 3-5 years). Use only APC-approved replacement battery cartridges.
- 안전이 최우선입니다. Disconnect the UPS from AC power and turn it off before attempting battery replacement.
- 절차: Follow the specific instructions provided with the replacement battery cartridge for safe removal and installation.
2. 청소
Keep the ventilation openings clear of dust and debris to ensure proper airflow. Use a dry cloth to clean the exterior of the UPS.
문제 해결
이 섹션에서는 일반적인 문제에 대한 해결책을 제공합니다. 보다 복잡한 문제의 경우 APC 기술 지원팀에 문의하십시오.
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| UPS가 켜지지 않습니다. | 전원 입력 없음; 배터리 방전 | Check AC input connection; allow battery to charge for several hours. |
| UPS에서 계속해서 경고음이 울립니다. | On battery mode; overload condition | Check AC input; reduce connected load. |
| Battery indicator shows low charge | Battery needs charging or replacement | Allow UPS to charge; perform a battery self-test; replace battery if necessary. |
명세서
- 상표: 항공우주국(APC)
- 모델: SRT10KRMXLT-5KTF2
- 제품 크기: 1 x 1 x 1 인치
- 품목 무게: 2파운드
- 재료: 금속
- 호환 장치: 섬기는 사람
- 장착 유형: Rack mount, Tower
- 첫 이용 가능 날짜: 23년 2017월 XNUMX일
보증 및 지원
APC products are backed by a limited warranty. For detailed warranty information, please refer to the documentation included with your product or visit the official APC website. For technical assistance, troubleshooting, or to inquire about replacement parts, please contact APC customer support.
온라인 리소스: www.apc.com
