소개
This manual provides detailed instructions for the setup, operation, and maintenance of your Hormann HSE4 BS remote control. The HSE4 BS is a 4-button handheld transmitter featuring Hormann's secure BiSecur wireless technology, designed for controlling garage doors, entrance gates, and other compatible Hormann operators.
Each of the four buttons can be individually programmed to control different functions or devices, offering convenience and flexibility. The integrated keyring eyelet allows for easy attachment to your keys, ensuring it is always accessible.
이미지: 앞면 view of the Hormann HSE4 BS remote control, showing its sleek black design and four distinct control buttons.
설정 및 프로그래밍
The Hormann HSE4 BS remote control comes with a pre-installed lithium metal battery. Before initial use, it is necessary to program the remote control to your Hormann operator or copy the code from an existing remote.
Programming to an Existing Remote Control (Hand-to-Hand Copy)
- 새 리모컨을 준비하세요: Hold the new HSE4 BS remote control.
- Prepare the Existing Remote: Take your existing, working Hormann remote control.
- 페어링 시작: Press and hold the desired button on your existing remote control. The LED on the existing remote will light up.
- Transfer Code: While still holding the button on the existing remote, immediately press and hold the corresponding button on the new HSE4 BS remote control.
- 확인: The LED on the new HSE4 BS remote will flash slowly, then rapidly, and finally stay illuminated, indicating successful programming. Release both buttons.
- 테스트 기능: Test the newly programmed button with your operator. If it does not work, repeat the process. It may require several attempts for successful pairing.
메모: Some users report that pressing both buttons simultaneously (existing and new) without delay can improve success rates.
Programming Directly to the Operator Unit
For optimal security and functionality, or if you do not have an existing remote, it is recommended to program the HSE4 BS directly to your Hormann operator unit. The exact procedure may vary slightly depending on your specific operator model (e.g., SupraMatic, ProMatic, RotaMatic). Refer to your operator's instruction manual for precise steps. Generally, the process involves:
- Access Operator: Locate the programming button on your Hormann garage door or gate operator unit. This button is often labeled "P" or "PRG".
- 학습 모드 활성화: Press and release the programming button on the operator. The operator's LED indicator will typically start flashing, indicating it is in learning mode.
- 전송 코드: Within a few seconds, press and hold the desired button on your new HSE4 BS remote control.
- 확인: The operator's LED will change its flashing pattern or illuminate steadily to confirm successful programming. Release the button on the remote.
- 테스트 기능: Test the remote control with the operator.
중요 호환성 참고 사항: This remote control is compatible with Hormann operators such as SupraMatic E/P, SuperMatic HT, ProMatic, ProMatic Accu, RollMatic, RotaMatic/P/PL, RotaMatic Accu Solar, VersaMatic/P, VersaMatic Accu Solar, LineaMatic/P, and LineaMatic Accu Solar. It is 아니다 suitable for the Liftronic garage door motor.
작동 지침
Once programmed, operating your Hormann HSE4 BS remote control is straightforward.
- 기능 선택 : Identify the button on your remote control that has been programmed for the desired function (e.g., opening/closing the garage door, opening the gate).
- 활성화: Press the corresponding button firmly for approximately one second.
- 관찰하다: The operator will respond according to its programmed function. The remote's LED will illuminate during transmission.
이미지: 클로즈업 view of the four control buttons on the Hormann HSE4 BS remote control, with a small LED indicator above them.
유지
The Hormann HSE4 BS remote control requires minimal maintenance to ensure long-lasting performance.
배터리 교체
The remote control is powered by a single lithium metal battery (CR2032 type, typically). When the battery is low, the remote's LED indicator may flash briefly or not illuminate at all when a button is pressed, or the range may decrease significantly.
- 오픈 Casing: 리모컨을 조심스럽게 열어보세요asing. This usually involves prying open a small seam with a thin tool or screwdriver.
- 오래된 배터리 제거: Remove the old CR2032 battery. Note its polarity (+/-).
- 새 배터리를 삽입하세요: Insert a new CR2032 lithium metal battery, ensuring correct polarity.
- C 닫기asing: c를 찍으세요asing를 다시 단단히 결합하세요.
처분: 사용한 배터리는 지역 규정에 따라 폐기하십시오. 배터리를 일반 생활 쓰레기와 함께 버리지 마십시오.
청소
리모컨은 부드럽고 마른 천으로 닦으십시오. 연마성 세제나 용제를 사용하지 마십시오. 리모컨이 손상될 수 있습니다.asing와 전자제품.
이미지: 뒤로 view of the Hormann HSE4 BS remote control, showing the model number (HSE4-868-BS) and regulatory markings.
문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 리모컨으로 문/대문이 작동하지 않습니다. |
|
|
| 리모컨의 LED 표시등이 켜지지 않습니다. | 배터리가 방전되었습니다. | 배터리를 교체하세요. |
| 작동 범위가 감소했습니다. |
|
|
명세서
- 모델: HSE4 BS
- 제조업체: 호르만
- 부품 번호: 4511736
- 치수(길이 x 너비 x 높이): 11 x 6.5 x 3cm(약 4.3 x 2.6 x 1.2인치)
- 무게: 40그램(약 1.4온스)
- 색상: 검은색
- 버튼 수: 4
- 연결 기술 : Radio Frequency (BiSecur)
- 전원: 배터리 작동
- 배터리 유형: 1 x Lithium metal (CR2032), included
- 특징: Pre-programmed (can be reprogrammed)
- Compatible Operators: SupraMatic E/P, SuperMatic HT, ProMatic, ProMatic Accu, RollMatic, RotaMatic/P/PL, RotaMatic Accu Solar, VersaMatic/P, VersaMatic Accu Solar, LineaMatic/P, LineaMatic Accu Solar, Hormann ProMatic Serie 4.
- Incompatible Operators: Liftronic garage door motor.
- 원산지: 독일
보증 정보
Based on available product information, there is no manufacturer's warranty explicitly stated for this product. Please refer to your point of purchase for any applicable retailer warranties or return policies.
고객 지원
Should you encounter any issues not covered in this manual or require further assistance, please contact Hormann customer support or your authorized Hormann dealer. You can typically find contact information on the official Hormann web사이트나 제품 판매점을 통해 구매하세요.
When contacting support, please have your product model (HSE4 BS) and any relevant purchase details ready.
For additional resources and product information, visit the official Hormann web대지: www.hormann.com
