컬리건 WH-HD200-C 주택 전용 정수 시스템 사용 설명서

1. 서론

This manual provides detailed instructions for the installation, operation, and maintenance of your Culligan WH-HD200-C Whole House Water Filter System. This heavy-duty system is designed to filter water entering your home, reducing sediment, rust, and scale to improve water quality and protect your plumbing and appliances.

2. 안전 정보

• 설치 또는 유지보수 작업을 시작하기 전에 항상 메인 급수 밸브를 잠그십시오.
• Release water pressure from the system by opening a nearby faucet before servicing.
• 설치 및 유지 보수 작업 중에는 안전 안경과 장갑과 같은 적절한 개인 보호 장비를 착용하십시오.
• 수압을 복원하기 전에 모든 연결부가 단단히 고정되어 있고 누수가 없는지 확인하십시오.
• If you are not comfortable performing the installation, consult a qualified plumber.
• Do not overtighten plastic components, as this may cause damage.

3. 패키지 내용

The Culligan WH-HD200-C system includes the following components:

• WH-HD200-C Filter Housing with Clear Sump
• 장착 브래킷
• 하우징 렌치
• Filter Life Indicator (battery included)
• Built-in Shut-off and Bypass Valve
• 압력 방출 밸브
• 설치 가이드

Note: Filter cartridges are sold separately. Refer to the "Compatible Cartridges" section for recommended options.

4. 설정 및 설치

The Culligan WH-HD200-C is a point-of-entry system designed for installation on your main water line. It should be installed after your water meter or pressure tank, and before any other water treatment devices (e.g., water softeners, drinking water filters).

4.1. 설치 위치 선택

• Select a location that is easily accessible for filter changes and maintenance. Ensure at least 1.5 inches of clearance below the housing for removal.
• The system requires sufficient space on either side for plumbing connections.
• Mount the system to a sturdy surface, such as a wood stud or concrete wall, to support its weight when filled with water.

4.2. Tools and Materials Required (Not Included)

• 파이프 커터 또는 쇠톱
• 조정 가능한 렌치(2)
• File or deburring tool
• Teflon tape (thread sealant)
• 연필이나 마커
• 줄자
• Drill and appropriate drill bits (for mounting bracket)
• Pipe fittings suitable for your plumbing type (e.g., 1-inch quick connect adapters, compression fittings, or sweat fittings).
• Food-grade silicone grease (for O-rings, recommended for easier maintenance and leak prevention).

4.3. 설치 단계

1. 설치 준비:
   • 집에 공급되는 주요 물 공급을 차단하십시오.
   • Open the nearest faucet to relieve water pressure and drain the pipes.
2. 장착 브래킷 부착:
   • Align the holes on the mounting bracket with the corresponding holes on the back of the filter head.
   • Secure the bracket to the filter head using the provided screws. Ensure the arrows on the filter head align with your water flow direction (e.g., left to right).
3. Prepare Pipe Fittings:
   • Wrap the pipe threads of your chosen fittings (e.g., 1-inch quick connect adapters) with approximately 6 inches of Teflon tape in a clockwise direction.
   • Screw the fittings into the filter head by hand, then tighten with a wrench. Do not overtighten.
4. Cut and Prepare Main Water Line:
   • Measure the length of your filter head with the attached fittings. Determine the section of your main water line that needs to be removed to accommodate the filter system. Allow for sufficient pipe engagement into the fittings.
   • Mark the section of pipe to be removed.
   • Using a pipe cutter or hacksaw, carefully cut and remove the marked section of pipe.
   • File down any sharp edges or burrs from the cut pipe ends to ensure a smooth connection.
5. 필터 시스템 설치:
   • Position the filter system into the gap in your main water line.
   • Push the pipe ends firmly into the quick connect adapters until they hit a hard stop, ensuring full engagement.
   • Drill the mounting bracket into your wall using appropriate screws for your wall type (e.g., wood screws for studs, masonry anchors for concrete).
6. 필터 카트리지 삽입:
   • Ensure the filter cartridge is properly seated over the standpipe at the bottom of the clear housing.
   • Carefully screw the clear housing with the filter cartridge into the filter head. Hand-tighten first, then use the provided housing wrench to tighten firmly. Do not overtighten.
7. 물 공급 복구:
   • Turn the bypass valve to the "FILTER" position using the housing wrench. It may be stiff the first time.
   • Slowly turn on the main water supply to your home.
   • Slowly press the red pressure relief button on top of the filter head to release any trapped air.
   • Open the nearest faucet and let water run for approximately 10 minutes to flush the filter cartridge and allow the system to depressurize. Some sputtering is normal initially.
   • Check all connections for leaks. If leaks occur, turn off water, relieve pressure, and re-tighten connections.

4.4. 설치영상

4.5. 제품 이미지

5. 운영

5.1. 바이패스 밸브

The system features a built-in bypass valve, allowing you to divert water around the filter for maintenance or if filtered water is not required. The valve has three positions:

• 필터: Water flows through the filter cartridge. (Default operating position)
• 우회로: Water bypasses the filter. Use this position when changing the filter or if filtered water is not needed.
• OFF : Water supply to the system is shut off.

To change the valve position, use the provided housing wrench for leverage, as the valve can be stiff.

5.2. 필터 수명 표시기

The filter life indicator is a battery-operated monitor that helps track when your filter cartridge needs replacement. Press the "RESET" button for 2 seconds after each filter change to reset the timer.

6. 유지관리

6.1. 필터 카트리지 교체

Filter cartridges should be replaced regularly based on water quality and usage, or when the filter life indicator signals replacement. The clear housing allows for visual inspection of the filter's condition.

1. Turn off the main water supply to the system by setting the bypass valve to "OFF" or "BYPASS".
2. Open a nearby faucet to relieve pressure.
3. Press the red pressure relief button on top of the filter head to release any remaining pressure.
4. Using the housing wrench, unscrew the clear filter housing.
5. 오래된 필터 카트리지를 제거하고 올바르게 폐기하십시오.
6. Clean the inside of the filter housing with warm, soapy water. Rinse thoroughly.
7. Inspect the O-ring for any damage or wear. Apply food-grade silicone grease to the O-ring to ensure a proper seal and prevent leaks. Replace the O-ring if necessary.
8. Insert a new filter cartridge, ensuring it seats correctly over the standpipe.
9. Screw the clear housing back onto the filter head. Hand-tighten first, then use the housing wrench to tighten firmly. Do not overtighten.
10. Slowly turn the bypass valve to the "FILTER" position.
11. 주요 물 공급장치를 천천히 켜세요.
12. Press the red pressure relief button to release trapped air.
13. Flush the new filter by running water from a nearby faucet for 10 minutes.
14. Reset the filter life indicator by holding the "RESET" button for 2 seconds.

7. 문제 해결

If troubleshooting steps do not resolve the issue, please contact Culligan customer support.

8. 사양

• 모델: WH-HD200-C
• 입구/출구 크기: 1 인치
• 하우징 소재: Clear Sump, Stainless Steel Reinforced Cap
• 제품 크기: 8.26인치 길이 x 7.48인치 너비 x 16.33인치 높이
• 무게: 3 파운드
• 최대 용량: 16,000 Gallons (with compatible filter)
• 특별 기능: Heavy Duty, WQA Certified, Rust Resistant, Built-in Shut-off/Bypass, Pressure Relief Valve, Filter Life Indicator
• 설치 유형: 줄을 서서
• 정화 방법: Sedimentation (depends on filter cartridge)
• 전원: Not Powered (Filter Life Indicator uses 1 Lithium Metal battery, included)

9. 보증 정보

Culligan products are backed by a limited warranty. For specific details regarding your product's warranty coverage, including terms, conditions, and how to make a claim, please refer to the warranty card included with your purchase or visit the official Culligan web사이트. 보증을 위해 구매 증빙 자료를 보관하세요.

10. 고객 지원

If you have any questions, require assistance with installation, operation, or maintenance, or need to order replacement parts, please contact Culligan Customer Support:

• Web대지: www.컬리건.com
• 핸드폰: Refer to your product packaging or the Culligan web가장 최신 연락처 정보를 제공하는 사이트입니다.
• 온라인 리소스: 방문하다 culligandiy.com for additional DIY installation guides and resources.