1. 서론
This manual provides essential information for the proper installation, operation, and maintenance of your DB DRIVE K5 12D4V2 Okur(R) K5v2 Series 12-inch Subwoofer. Please read this manual thoroughly before attempting to install or operate the subwoofer to ensure optimal performance and safety.
The DB DRIVE K5 12D4V2 is a high-performance 12-inch subwoofer designed for car audio systems, featuring robust construction and advanced components for powerful and clear bass reproduction.
2. 주요 특징
- 12-inch subwoofer for deep bass response.
- 1,500W maximum power handling.
- 2.5-inch voice coil with 4-layer 4-ohm DVC (Dual Voice Coil) configuration.
- Heavy-gauge stamped steel basket for durability.
- Injection-molded bowl PP (Polypropylene) dust cap.
- High-temperature voice coil for extended performance.
- KSV voice-coil former.
- High-excursion butyl rubber surround for enhanced cone movement.
- Heavy-gauge spring terminals for secure wire connections.
- Proprietary PVC gasket for a sealed fit.
3. 안전 정보
항상 다음 안전 예방 조치를 준수하십시오.
- 전문 설치 권장: Installation of car audio components can be complex. If you are unsure about any step, seek assistance from a qualified professional installer.
- 배터리 분리: 설치를 시작하기 전에 전기 합선 및 손상을 방지하기 위해 차량 배터리의 음극 단자를 분리하십시오.
- 적절한 배선: Ensure all wiring is correctly connected according to the amplifier and subwoofer specifications. Incorrect wiring can lead to damage or fire.
- 통풍: 서브우퍼 주변에 적절한 환기를 확보하십시오. amp과열을 방지하는 lifier.
- 볼륨 레벨: Prolonged exposure to high volume levels can cause hearing damage. Use caution when adjusting volume.
- 안전한 장착: 급정거나 사고 발생 시 서브우퍼가 날아가지 않도록 단단히 고정하십시오.
4. 설정 및 설치
Proper installation is crucial for optimal performance and longevity of your subwoofer. This section provides general guidelines. Refer to your amplifier's manual for specific wiring diagrams and power requirements.
4.1. Choosing an Enclosure
The DB DRIVE K5 12D4V2 subwoofer requires a suitable enclosure for proper operation. Common enclosure types include sealed, ported (vented), or bandpass. The choice depends on desired sound characteristics and available space. Consult a car audio specialist or online resources for recommended enclosure volumes and tuning frequencies for this specific model.
4.2. 서브우퍼 배선
The K5 12D4V2 features a 4-layer 4-ohm DVC (Dual Voice Coil) configuration. This allows for various wiring options to achieve different impedance loads at the amp증폭기. 일반적인 구성은 다음과 같습니다.
- 병렬 배선(2옴): Connect the positive terminals of both voice coils together and the negative terminals of both voice coils together. This results in a 2-ohm load, suitable for amp앰프는 2옴에서 안정적입니다.
- 직렬 연결(8옴): 한 음성 코일의 양극 단자를 다른 음성 코일의 음극 단자에 연결합니다. 나머지 양극 및 음극 단자는 다음 위치에 연결합니다. amplifier. This results in an 8-ohm load.
Always match the subwoofer's impedance load to the amplifier's stable impedance rating. Refer to the wiring diagram provided with your amp리퍼.
4.3. 연결하기 Amp리퍼
Connect the wired subwoofer to the appropriate speaker output terminals on your amplifier. Ensure polarity is correct (+ to + and - to -). Use high-quality speaker wire of adequate gauge to minimize power loss.
Figure 1: DB DRIVE K5 12D4V2 Subwoofer. This image displays the top view of the subwoofer, highlighting its black cone with a red trim, the durable black frame, and the heavy-gauge spring terminals for electrical connections. The red magnet cover is visible at the bottom.
5. 사용 설명서
Once installed, follow these general guidelines for operating your subwoofer:
- 초기 전원 켜기: After installation, turn on your car's audio system at a low volume. Gradually increase the volume and check for proper operation.
- Amp설정: 게인, 크로스오버 주파수 및 위상 설정을 조정하십시오. amplifier to blend the subwoofer's output seamlessly with your main speakers.
- 얻다: Set the gain to match the output voltage of your head unit. Avoid setting it too high, which can cause distortion.
- 저역 통과 필터(LPF): Set the LPF to filter out frequencies above the subwoofer's intended range (typically 60Hz-100Hz).
- 단계: Adjust the phase (0° or 180°) to ensure the subwoofer's output is in sync with your main speakers, preventing cancellation or weak bass.
- 침입 기간: Allow a break-in period of approximately 20-30 hours of normal listening before pushing the subwoofer to its limits. This allows the suspension components to loosen up and perform optimally.
- 과속 방지: Do not continuously play the subwoofer at distorted levels. This can cause permanent damage to the voice coil and other components.
6. 유지관리
The DB DRIVE K5 12D4V2 subwoofer requires minimal maintenance:
- 청소: 부드럽고 마른 천으로 콘과 주변을 닦아주세요. 강한 화학 물질이나 연마성 세제는 사용하지 마세요.
- 점검: Periodically inspect the wiring connections to ensure they are secure and free from corrosion. Check the subwoofer's surround for any signs of cracking or damage.
- 환경적 요인: Protect the subwoofer from extreme temperatures, direct sunlight, and moisture, which can degrade its performance and lifespan.
7. 문제 해결
서브우퍼에 문제가 발생하면 다음의 일반적인 문제와 해결 방법을 참조하세요.
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 서브우퍼에서 소리가 나지 않습니다 |
|
|
| 왜곡되거나 불분명한 저음 |
|
|
| 서브우퍼 과열 |
|
|
If the problem persists after attempting these solutions, contact DB DRIVE customer support or a qualified car audio technician.
8. 사양
| 특징 | 세부 사항 |
|---|---|
| 상표 | DB 드라이브 |
| 모델 번호 | SB-58148 |
| 스피커 크기 | 12 인치 |
| 최대 전력 처리 | 1,500와트 |
| 음성 코일 | 2.5" 4-layer 4-ohm DVC |
| 바구니 재료 | Heavy-gauge stamp에드 스틸 |
| 더스트 캡 | Injection-molded bowl PP |
| 서라운드 소재 | High-excursion butyl rubber |
| 터미널 | Heavy-gauge spring terminal |
| 한국어: | 731215374418, 782386080233 |
| 장착 유형 | 플러시 마운트 |
| 첫 번째 이용 가능 날짜 | 30년 2016월 XNUMX일 |
9. 보증 및 지원
For information regarding warranty coverage, technical support, or service, please refer to the official DB DRIVE web해당 웹사이트를 방문하거나 고객 서비스 부서에 직접 문의하십시오. 보증 청구를 위해 구매 증빙 자료를 보관하십시오.
DB DRIVE Official Web대지: www.dbdrive.net (참고: 이것은 플레이스홀더입니다. URL실제 공식 정보를 확인해 주세요. website for DB DRIVE.)
