KICKER CXA1200.1 1200와트 모노 클래스 D 서브우퍼 Ampliifier 사용 설명서

1. 서론

This manual provides detailed instructions for the installation, operation, and maintenance of your KICKER CXA1200.1 1200-Watt Mono Class D Subwoofer Amplifier. Please read this manual thoroughly before use to ensure proper function and safety.

The KICKER CXA1200.1 amplifier is designed to deliver powerful bass performance for your vehicle's audio system. It features a Class D power plant, Failsafe Integration Technology (FIT), KickEQ bass boost, and adjustable crossover and subsonic filters for precise sound tuning.

2. 안전 정보

경고:

• 전기 연결을 하기 전에 항상 차량의 배터리를 분리하세요.
• 전기 위험을 방지하기 위해 적절한 접지를 확인하십시오.
• 설치를 피하십시오 amplifier in locations exposed to moisture or extreme temperatures.
• Use appropriate gauge wiring for power and speaker connections to prevent overheating.
• 높은 음압은 영구적인 청력 손실을 유발할 수 있습니다. 음량을 조절할 때는 주의하십시오.
• 이 제품에는 캘리포니아 주에서 암, 선천적 기형 또는 기타 생식 기능 장애를 유발하는 것으로 알려진 화학 물질이 포함되어 있습니다(캘리포니아 주 법률 제65호 경고).

3. 패키지 내용

포장을 풀 때 모든 품목이 들어 있고 상태가 양호한지 확인하세요.

• KICKER CXA1200.1 Mono Amp리퍼
• 장착 하드웨어
• 사용 설명서(이 문서)
• Remote Bass Control (if included with your model)

4. 설정 및 설치

최적의 성능과 안전을 위해서는 올바른 설치가 필수적입니다. 설치 단계에 대해 잘 모르시겠다면 전문 설치 기사에게 문의하세요.

4.1 장착 Amp리퍼

Choose a secure, dry location with adequate ventilation. Avoid mounting on carpet or in enclosed spaces without airflow. Use the provided mounting hardware to secure the amp증폭기를 단단히 고정합니다.

4.2 배선 연결

아래 그림을 참조하여 올바르게 배선하십시오. 모든 연결부가 단단히 고정되고 절연되었는지 확인하십시오.

그림 1: 뒤쪽 view of the KICKER CXA1200.1 amplifier showing the power (GND, REM, +12V) and speaker output terminals. Ensure correct polarity and secure connections.

4.2.1 전원 연결

1. 접지(GND): Connect a heavy-gauge wire (minimum 4 AWG recommended) from the amplifier's GND terminal to a clean, bare metal point on the vehicle's chassis. The ground wire should be as short as possible.
2. 원격(REM): Connect a 18 AWG wire from the amplifier's REM terminal to the remote turn-on lead of your head unit. This wire turns the amp앰프를 오디오 시스템과 함께 켜고 끌 수 있습니다.
3. +12V(전원): Connect a heavy-gauge wire (minimum 4 AWG recommended) from the amplifier's +12V terminal directly to the positive terminal of the vehicle's battery. Install an appropriate fuse (not supplied) within 18 inches of the battery.

4.2.2 스피커 연결

Connect your subwoofer(s) to the SPEAKER terminals. The CXA1200.1 is a mono amplifier, designed for a single channel output. Ensure the total impedance of your subwoofers matches the amplifier's stable operating impedance (typically 1 Ohm minimum for this model).

4.2.3 입력 연결

그림 2: 앞쪽 view of the KICKER CXA1200.1 amplifier showing the RCA input/output, control knobs, and indicator lights. This panel allows for fine-tuning of audio settings.

Connect the RCA output from your head unit or signal processor to the INPUT RCA jacks on the amplifier. The CXA1200.1 features Failsafe Integration Technology (FIT) which allows it to accept high-level speaker outputs directly from a factory radio if RCA outputs are not available. Use a KICKER KISL adapter for high-level input if needed (sold separately).

5. 사용 설명서

설치 후 조정하세요 amp최적의 사운드 성능을 위한 리파이어 설정.

5.1 제어판 이상view

The control panel (refer to Figure 2) provides access to various adjustments:

• INPUT LEVEL (LO/HI): Selects between low-level (RCA) and high-level (speaker wire) input.
• 이득: Adjusts the input sensitivity to match the output of your head unit. Start with the gain at minimum and slowly increase until distortion is heard, then back off slightly.
• X-OVER FREQ (Hz): Adjusts the low-pass filter frequency (50-200 Hz). This allows only frequencies below the set point to pass to the subwoofer.
• BASS BOOST (dB): Provides up to 12 dB of bass enhancement at 40 Hz. Use sparingly to avoid distortion.
• 원격 베이스: Connects an optional wired remote bass control for convenient level adjustment from the driver's seat.
• PRT (Protection) Indicator: 다음과 같은 경우에 켜집니다. amplifier is in protection mode due to overheating, low voltage, or short circuit.
• PWR(전력) 표시기: 다음과 같은 경우에 켜집니다. amp앰프는 전원이 켜져 있고 정상적으로 작동 중입니다.

5.2 초기 설정 절차

1. Turn off your head unit and set all tone controls (bass, treble, balance, fader) to flat or center.
2. 설정하다 amplifier's GAIN control to minimum.
3. Set the X-OVER FREQ to your desired low-pass frequency (e.g., 80 Hz).
4. Play a dynamic music track.
5. Slowly increase the head unit volume until it reaches about 3/4 of its maximum level.
6. 천천히 증가 amplifier's GAIN control until you hear audible distortion, then back off slightly.
7. Adjust the BASS BOOST and X-OVER FREQ to fine-tune the sound to your preference.

6. 사양

7. 문제 해결

문제가 발생하는 경우 amp증폭기 관련 문의는 지원팀에 연락하기 전에 다음 표를 참조하십시오.

8. 유지관리

The KICKER CXA1200.1 amplifier requires minimal maintenance. Keep the unit clean and free from dust and debris. Periodically check all wiring connections for tightness and corrosion. Do not use harsh chemicals or abrasive cleaners.

9. 보증 및 지원

KICKER products are designed for years of trouble-free operation. For specific warranty information, please refer to the warranty card included with your product or visit the official KICKER web대지.

For technical support or service inquiries, please contact KICKER customer service or visit their official brand store:

아마존에서 KICKER 스토어를 방문하세요

10. 법적 고지사항

This product may be subject to Proposition 65 warnings. For more information, please refer to the product packaging or KICKER's official web대지.