WEN 3962T 10-Inch Two-Speed Band Saw Instruction Manual

1. 서론

This instruction manual provides essential information for the safe and effective operation, assembly, maintenance, and troubleshooting of your WEN 3962T 10-Inch Two-Speed Band Saw. Please read this manual thoroughly before operating the tool and keep it for future reference. Understanding and following these instructions will ensure optimal performance and extend the life of your band saw.

2. 일반 안전 지침

전동공구를 사용할 때는 항상 안전을 최우선으로 고려해야 합니다. 안전 지침을 준수하지 않으면 심각한 부상이나 재산 피해가 발생할 수 있습니다.

• 모든 지침 읽기: Familiarize yourself with the tool's operation and safety procedures.
• 눈 보호 장비 착용: Always wear ANSI-approved safety goggles or a face shield.
• 청력 보호 장비를 착용하세요: 작업 중에는 귀마개나 이어머프를 착용하세요.
• 작업 공간을 깨끗하게 유지하세요: 어수선한 지역과 벤치는 사고를 유발합니다.
• 위험한 환경을 피하십시오: 전동공구를 사용하지 마십시오amp 젖은 장소 또는 비에 노출시키십시오. 작업 영역을 밝게 유지하십시오.
• 어린이의 접근을 차단하세요: 모든 방문객은 작업장에서 안전한 거리를 유지해야 합니다.
• 안전한 작업물: 항상 cl을 사용하십시오.amp또는 작업물을 고정하기 위한 바이스.
• 공구를 무리하게 사용하지 마십시오. 설계된 속도로 작업을 더 잘 수행하고 더 안전하게 수행할 것입니다.
• 올바른 도구 사용: 작은 도구나 부착물에 무거운 도구의 작업을 강제로 시키지 마십시오.
• 적절한 옷차림: Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Non-slip footwear is recommended. Wear protective hair covering to contain long hair.
• 도구를 주의해서 관리하세요: 최상의 안전한 성능을 위해 도구를 날카롭고 깨끗하게 유지하십시오. 부속품 윤활 및 교체 지침을 따르십시오.
• 연결 해제 도구: 정비를 하거나, 액세서리를 교체하거나, 사용하지 않을 때는 공구의 전원을 차단하십시오.
• 우발적인 시작을 방지하세요: Make sure switch is off when plugging in.
• 손상된 부품 확인: 공구를 추가로 사용하기 전에 손상된 보호대 또는 기타 부품이 제대로 작동하고 의도한 기능을 수행하는지 신중하게 확인해야 합니다.

3. 패키지 내용

Verify that all items are present upon unpacking. If any parts are missing or damaged, contact WEN customer service immediately.

• WEN 10-Inch Two-Speed Band Saw
• 서다
• Flexible Work Light
• 3-in-1 Dust Port (1-3/4, 2-3/4, 4 inches)
• Fence for straight cuts
• Miter Gauge for angled cuts
• Band Saw Blade (72-inch, 1/8 to 1/2 inches in size)

Figure 3.1: Complete WEN 3962T Band Saw with stand and worklight.

4. 설치 및 조립

Follow these steps for proper assembly and initial setup of your band saw.

1. 스탠드 조립: Securely attach the stand components according to the included hardware. Ensure all bolts are tightened to provide a stable base for the saw.
2. Mount the Band Saw: Carefully lift the band saw onto the assembled stand and secure it using the provided mounting hardware.
3. 블레이드 설치:
   • 칼날 덮개를 여세요.
   • 톱니가 테이블 쪽을 향하도록 톱날을 위쪽 및 아래쪽 휠 주위에 조심스럽게 위치시키십시오.
   • Adjust the blade tension using the tension knob until the blade is taut but not overly stressed.
   • Adjust the blade guides and thrust bearings to ensure proper blade tracking and support.
   

   그림 4.1: 내부 view showing blade wheels and tensioning.
   

   Figure 4.2: Close-up of blade guide and thrust bearings.

4. Install the Work Table: Attach the spacious 14-1/8 x 12-1/2 inch work table. Ensure it is level with the blade and can be securely locked at various angles up to 45 degrees.
5. Attach the Fence and Miter Gauge: Install the fence for straight cuts and the miter gauge for angled cuts onto the work table.
6. Connect the Work Light: Position the flexible work light to illuminate the worktable effectively.
7. Connect Dust Collection: Attach a dust extractor hose to the 3-in-1 dust port (1-3/4, 2-3/4, or 4 inches) to maintain a clean work environment.

Figure 4.3: Work table with fence and miter gauge installed.

Figure 4.4: Flexible work light in position.

Figure 4.5: 3-in-1 dust port for dust collection.

5. 사용 설명서

Understand the features and controls of your band saw for efficient and safe operation.

• 전원 스위치: Locate the main power switch for turning the saw on and off.
• 속도 선택: The saw operates at two speeds: 1520 FPM (Feet Per Minute) and 2620 FPM. Select the appropriate speed for your material. Lower speeds are generally for harder materials or intricate cuts, while higher speeds are for softer woods and faster cutting.
• Work Table Adjustment: The work table can be swiveled up to 45 degrees for angled cuts. Loosen the locking mechanism, adjust to the desired angle, and re-tighten securely.
• Using the Fence: For straight cuts, position the fence parallel to the blade and lock it in place.
• 마이터 게이지 사용: For precise angled cross-cuts, use the miter gauge. Adjust it to the desired angle and guide the workpiece against it.
• 절단 절차:
  1. 가공물에 못, 나사 또는 기타 이물질이 없는지 확인하십시오.
  2. Adjust the blade guide assembly so it is approximately 1/8 inch above the workpiece.
  3. Turn on the saw and allow the blade to reach full speed before beginning the cut.
  4. Feed the workpiece slowly and steadily into the blade. Do not force the material.
  5. Keep hands clear of the blade path. Use a push stick for smaller pieces.

6. 유지관리

Regular maintenance ensures the longevity and safe operation of your band saw.

• 블레이드 교체: Replace dull or damaged blades promptly. Always disconnect power before changing blades.
• 청소: Regularly clean sawdust and debris from the work table, blade guides, and internal components. Use a vacuum or compressed air.
• 매끄럽게 하기: Periodically lubricate moving parts as specified in the full product manual (not provided here).
• 칼날 장력: Check blade tension before each use. Proper tension prevents blade breakage and ensures accurate cuts.
• Blade Guides and Bearings: Inspect blade guides and thrust bearings for wear and proper adjustment. Replace worn components as needed.
• 테이블 왁싱: Apply paste wax to the cast iron table to reduce friction and prevent rust.

7. 문제 해결

일반적인 문제와 해결 방법은 이 섹션을 참조하세요.

8. 사양

9. 보증 및 지원

The WEN 3962T 10-Inch Two-Speed Band Saw comes with a 2년 한정 보증 for residential use. For commercial use, a 90-day warranty applies. This warranty covers defects in material and workmanship. For warranty claims, technical assistance, or to order replacement parts, please contact WEN customer service.

For further assistance, visit the official WEN website or contact their customer support line. Please have your model number (3962) and purchase information ready when contacting support.