1. 서론
The Avidsen 100108 Wireless GSM Alarm Kit is designed to provide security for your home or office. This kit includes a central unit with an integrated siren and presence sensor, a door/window magnetic contact, and two remote controls. Its GSM functionality allows for remote activation and alerts via SMS and calls.
Please read this manual carefully before installation and operation to ensure proper use and maximum security.
2. 패키지 내용
패키지에 모든 구성 요소가 들어 있는지 확인하세요.
- 1x Central Unit: Includes call function, siren, and presence (motion) sensor.
- 1x Door/Window Opening Sensor: Magnetic contact for entry points.
- 2x Remote Controls: For arming and disarming the system.
- 3x CR2 Batteries: Required for operation (included).
Image: Avidsen 100108 Wireless GSM Alarm Kit showing the central unit, remote controls, and a sensor.
3. 설정
3.1. 배터리 설치
- 중앙 장치: Open the battery compartment on the back of the central unit. Insert the 3 CR2 Lithium batteries, ensuring correct polarity (+/-). Close the compartment securely.
- 도어/창 센서: 센서 c를 엽니다asing and insert the required battery (refer to the sensor's specific markings for type and polarity).
- 원격 제어: Remote controls typically come with pre-installed batteries or require small button-cell batteries. Check the remote for a battery tab to remove or a compartment to open.
3.2. SIM Card Installation (for GSM Functionality)
The central unit requires a 2G GSM SIM card (not included) to enable SMS and call alerts. Ensure the SIM card is active and has sufficient credit if it's a prepaid card.
- Locate the SIM card slot on the central unit.
- SIM 카드를 슬롯에 올바른 방향으로 삽입하십시오.
- Power on the central unit. The unit will attempt to register with the GSM network.
3.3. 부품 배치
- 중앙 장치: Place the central unit in a central location within your protected area, away from direct sunlight and heat sources. Ensure it has good GSM signal reception.
- 도어/창 센서: Mount the magnetic contact on a door or window frame. Align the two parts (sensor and magnet) so they are no more than 1 cm apart when the door/window is closed.
- Presence Sensor (PIR): The central unit has an integrated PIR sensor. Position the unit to cover the desired detection area, typically a main hallway or room entrance. Avoid pointing it directly at heat sources or windows where sunlight or drafts might cause false alarms.
3.4. Pairing Remote Controls and Sensors
The remote controls and sensors are typically pre-paired with the central unit. If re-pairing is necessary or if adding new accessories, refer to the detailed pairing instructions in the full product manual (not provided here). Generally, this involves putting the central unit into a 'learning' mode and then activating the accessory.
4. 사용 설명서
4.1. 시스템 무장
To arm the alarm system, press the 팔 button on your remote control. The central unit will emit a confirmation sound, and an indicator light may illuminate, signifying that the system is armed. All connected sensors are now active.
4.2. 시스템 해제
To disarm the alarm system, press the 무장 해제 button on your remote control. The central unit will emit a different confirmation sound, and the indicator light will turn off, indicating the system is disarmed.
4.3. 비상 버튼
In case of an emergency, press the 공황 button (often depicted as a bell or lightning bolt) on your remote control. This will immediately trigger the siren and initiate GSM alerts (calls/SMS) to pre-programmed numbers, regardless of the system's armed status.
4.4. GSM Alert Functionality
When an alarm is triggered (e.g., by a motion sensor or door opening sensor), the central unit will:
- Activate the integrated siren.
- Send an SMS alert to pre-programmed phone numbers.
- Initiate a call to pre-programmed phone numbers.
To program alert numbers, refer to the detailed instructions in the full product manual. This typically involves sending specific SMS commands to the alarm unit's SIM card number from an authorized phone.
5. 유지관리
5.1. 배터리 교체
Regularly check the battery status of the central unit and all wireless sensors. Low battery indicators (audible alerts or flashing lights) will signal when batteries need replacement. Always replace with the specified battery type (e.g., CR2 for the central unit) and ensure correct polarity.
5.2. 청소
Clean the central unit and sensors periodically with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these can damage the device's surface or internal components. Keep sensors free from dust and obstructions to ensure optimal performance.
5.3. 시스템 테스트
It is recommended to test the alarm system periodically (e.g., monthly) to ensure all components are functioning correctly. This includes testing sensors, remote controls, siren, and GSM alert functionality.
6. 문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 시스템이 작동/해제되지 않습니다. | Low battery in remote control or central unit; remote control out of range; interference. | Replace remote control batteries; move closer to central unit; check for obstructions. |
| No GSM alerts (SMS/calls). | SIM card not inserted correctly; SIM card inactive or no credit; poor GSM signal; incorrect alert numbers programmed. | Reinsert SIM card; check SIM card status/credit; relocate central unit for better signal; verify programmed numbers. |
| 거짓 경보. | PIR sensor obstructed or exposed to heat sources/drafts; magnetic contact misaligned; low sensor battery. | Reposition PIR sensor; realign magnetic contact; replace sensor batteries. |
| 사이렌이 울리지 않습니다. | Siren disabled in settings; central unit battery low; siren malfunction. | Check system settings; replace central unit batteries; contact support if issue persists. |
7. 사양
- 상표: 아비센
- 모델 번호: 100108
- 전원: 배터리
- 배터리: 3 CR2 (Lithium), included
- 재료: 플라스틱
- 연결 기술 : 무선 전화
- 경고 유형: 오디오 및 모션
- 제어 방법: 원격 제어
- 제품 무게: 340g
- 장착 유형: Door (for magnetic contact)
- 호환 장치: Smartphone (for GSM alerts)
8. 보증 및 지원
보증 정보 및 기술 지원에 대해서는 구매 시 제공된 설명서를 참조하거나 Avidsen 공식 웹사이트를 방문하십시오. web사이트. 보증 청구를 위해 구매 증빙 자료를 보관하세요.
If you encounter issues not covered in this manual, please contact Avidsen customer service for assistance.
