소개
The HOBO UX100-003 is a compact USB data logger designed to accurately record temperature and relative humidity in indoor environments. It is suitable for monitoring conditions in various settings such as office buildings, warehouses, server rooms, and museums. This device stores over 42,000 temperature and humidity readings and features a user-replaceable battery. Data configuration and retrieval are managed through the free HOBOware software, compatible with both PC and Mac operating systems.
설정
1. 소프트웨어 설치
Before using the data logger, install the HOBOware software on your computer. This software is required for configuring the logger, launching logging sessions, and offloading recorded data. HOBOware is available as a free download for both Windows and macOS operating systems from the official HOBO web대지.
2. 배터리 설치
The UX100-003 uses a user-replaceable CR2032 coin cell battery. Ensure the battery is correctly installed before initial use. The typical battery life is one year. Refer to the Maintenance section for detailed battery replacement instructions.
3. 초기 구성
- Connect the HOBO UX100-003 data logger to your computer's USB port.
- Launch the HOBOware software.
- Use the software to configure logging parameters such as logging interval, start time, and alarm thresholds.
- Once configured, disconnect the logger from the USB port.
작동 지침
1. 배치
Place the data logger in the desired indoor environment where temperature and humidity monitoring is required. Ensure the sensor area (vented section on the right side of the device) is not obstructed to allow for accurate readings.
2. 데이터 로깅
Once configured and launched via HOBOware, the logger will automatically begin recording temperature and relative humidity data at the specified intervals. The LCD display will show current readings, logging status, and battery level.
3. 데이터 검색
- To retrieve data, connect the logger to your computer's USB port.
- Open the HOBOware software.
- Use the software to offload the recorded data. The data can then be view편집, 분석하여 추가 사용을 위해 내보냈습니다.
- After offloading, you can choose to stop the current logging session or reconfigure and launch a new one.
유지
배터리 교체
The HOBO UX100-003 is powered by one CR2032 lithium coin cell battery. When the battery indicator on the LCD display shows low power, or if the logger stops functioning, replace the battery promptly.
- Ensure the logger is not actively logging data. If it is, stop the logging session using HOBOware.
- 장치에서 배터리함을 찾으세요.
- 조심스럽게 배터리함을 열고 기존의 CR2032 배터리를 꺼내세요.
- Insert a new CR2032 battery, observing the correct polarity (+/-).
- 배터리 칸을 단단히 닫으세요.
- After battery replacement, it is recommended to connect the logger to HOBOware to verify functionality and re-launch a logging session if needed.
청소
데이터 로거의 외부를 부드러운 천으로 닦으십시오.amp cloth. Do not use abrasive cleaners or solvents. Ensure the sensor area remains free of dust and debris for accurate readings.
문제 해결
- Logger Not Connecting to HOBOware:
Ensure the USB cable is securely connected to both the logger and the computer. Try a different USB port or cable. Verify that HOBOware software is installed correctly and is the latest version. Restart your computer if necessary.
- Logger Display is Blank or Unresponsive:
Check the battery level. If the battery is low or depleted, replace it as described in the Maintenance section. If the issue persists after battery replacement, try removing and re-inserting the battery to reset the device.
- 부정확한 판독:
Ensure the logger's sensor area is not obstructed by dust, debris, or placed in an area with poor air circulation. Avoid placing the logger near heat sources, direct sunlight, or areas with rapid temperature/humidity fluctuations that do not represent the general environment.
- Logging Session Not Starting:
Connect the logger to HOBOware and verify that a logging session has been properly configured and launched. Check for any error messages within the software.
명세서
| 특징 | 세부 사항 |
|---|---|
| 모델 | UX100-003 |
| 온도 범위 | -20°C ~ +70°C (-4°F ~ +158°F) |
| 상대 습도 범위 | 15% ~ 95% RH 비응축 |
| 온도 정확도 | 0.21° ~ 0°C에서 ±50°C(0.38° ~ 32°F에서 ±122°F) |
| 상대습도 정확도 | ±3.5% RH from 25% to 85% RH (typical) |
| 데이터 저장 용량 | Over 42,000 temperature and humidity readings |
| 로깅 간격 | 1 second to 18 hours (configurable via HOBOware) |
| 배터리 유형 | CR2032 3V Lithium Coin Cell (user-replaceable) |
| 배터리 수명 | 1년(일반) |
| 인터페이스 | USB |
| 치수(높이 x 너비 x 깊이) | 3.44 x 1.44 x 0.6인치(8.74 x 3.66 x 1.52cm) |
| 무게 | 0.32 온스(9그램) |
| 방수 등급 | IP50 |
| 필요한 소프트웨어 | HOBOware or HOBOware Pro (free download) |
보증 정보
The HOBO UX100-003 Data Logger comes with a 1년 제조사 보증. This warranty covers defects in materials and workmanship under normal use. For specific terms and conditions, please refer to the warranty documentation provided with your purchase or contact HOBO customer support.
지원하다
For further assistance, technical support, or to download the latest version of HOBOware software, please visit the official HOBO web대지. NS website provides comprehensive resources, including FAQs, user forums, and contact information for customer service.
HOBOware Software: The free HOBOware software is essential for full functionality of your data logger. It allows for device configuration, data download, and analysis. Ensure you are using the latest version for optimal performance.
