COMPUTHERM Q7 프로그래밍 가능 디지털 실내 온도 조절기 사용 설명서

1. 서론

The COMPUTHERM Q7 is a programmable digital room thermostat designed to control heating and air conditioning systems. It allows for precise temperature regulation and offers multiple programming options to optimize comfort and energy efficiency. This manual provides detailed instructions for installation, operation, and programming of your Q7 thermostat.

이미지 1.1: The COMPUTHERM Q7 thermostat highlighting key features such as 0.5°C temperature increments, compatibility with heating/cooling systems, a temperature range of 5-40°C, 24-250V power compatibility, and 6 daily programs.

2. 안전 정보

• Always disconnect power to the heating/cooling system at the main circuit breaker before installing or servicing the thermostat.
• Installation should be performed by a qualified electrician or heating engineer if you are unsure about the wiring process.
• 온도 조절기를 직사광선, 극한 온도 또는 높은 습도에 노출시키지 마십시오.
• Ensure the thermostat is mounted at an appropriate height (approximately shoulder height) in the living area for accurate temperature readings.

3. 패키지 내용

다음 품목이 패키지에 포함되어 있는지 확인하세요.

• COMPUTHERM Q7 프로그래밍 가능 디지털 실내 온도 조절기
• 사용 설명서
• 장착 액세서리(나사, 벽면 플러그)

이미지 3.1: The COMPUTHERM Q7 thermostat shown alongside its retail packaging.

4. 제품 오버view

The COMPUTHERM Q7 thermostat features a clear digital display and intuitive buttons for easy operation.

이미지 4.1: 앞쪽 view of the COMPUTHERM Q7 thermostat, showing the digital display with time, program number, set temperature, and room temperature, along with the '+' and '-' adjustment buttons.

4.1. 디스플레이 요소

• 월/화/수/목/금/토/일: 요일 표시기.
• 시간: 현재 시간.
• 음식물: Current program number (0-6).
• 설정 온도: 원하는 온도.
• 실온: 현재 실내 온도.
• 난방/냉방 표시기: Icon indicating active heating or cooling.

4.2. 버튼

• +: Increase value, navigate forward.
• -: Decrease value, navigate backward.
• 보류: Activates/deactivates permanent manual temperature hold.
• 낮: Used for setting day/time and short-term programs.
• 빛: Activates backlight, adjusts backlight behavior.
• 복사: Copies program settings between days.
• 음식물: Enters/confirms program settings.
• 세트: Confirms settings, exits menus, cancels manual modes.

5. 설치

Proper installation is crucial for the thermostat's performance. Ensure power is disconnected before proceeding.

5.1. 온도 조절 장치 장착

1. Choose a suitable location on an interior wall, away from direct sunlight, drafts, and heat sources. The recommended height is approximately shoulder height.
2. Separate the front panel from the back plate of the thermostat.
3. Mark the drilling points on the wall using the back plate as a template.
4. 구멍을 뚫고 벽 플러그를 삽입합니다.
5. Secure the back plate to the wall with screws.

이미지 5.1: The COMPUTHERM Q7 thermostat installed on a wall in a typical home environment, demonstrating its discreet design.

5.2. 배선

The COMPUTHERM Q7 thermostat requires two AA batteries for power and connects to your heating/cooling system via two wires.

1. Ensure the main power supply to your heating/cooling system is OFF.
2. Connect the two wires from your boiler or heating/cooling system to connectors 1 그리고 2 on the thermostat's back plate. The polarity of these connections does not matter.
3. Connector 3 is typically not used for standard installations.
4. Once wired, carefully attach the front panel of the thermostat to the back plate.

이미지 5.2: 뒤쪽 view of the COMPUTHERM Q7 thermostat, illustrating the battery compartment and the wiring terminals (1, 2, 3) for connection to the heating/cooling system.

5.3. 배터리 설치

The thermostat is powered by 2 AA batteries.

1. 온도 조절 장치 뒷면의 배터리 칸을 엽니다.
2. AA 배터리 2개를 올바른 극성(+/-)에 맞춰 넣으세요.
3. 배터리 칸을 닫습니다.

6. 초기 설정

6.1. Resetting the Thermostat

If you need to reset the thermostat to factory settings, locate the small black 'Reset' button inside the battery compartment. Press and hold this button for approximately 5 seconds. The display will clear and reset.

6.2. 날짜 및 시간 설정

1. 를 누르세요 낮 button. The day of the week will start flashing.
2. 사용하세요 + or - 현재 날짜를 선택하려면 버튼을 클릭하세요.
3. 를 누르세요 낮 button again. The hour will start flashing.
4. 사용하세요 + or - 현재 시간을 설정하는 버튼입니다.
5. 를 누르세요 낮 button again. The minutes will start flashing.
6. 사용하세요 + or - 현재 분을 설정하는 버튼입니다.
7. 를 누르세요 세트 button to save the date and time settings.

7. Operating Modes & Programming

7.1. Manual Temperature Adjustment (Temporary Override)

To temporarily adjust the temperature until the next programmed period:

1. 정상 작동 모드에서는 다음을 사용하십시오. + or - 버튼을 눌러 원하는 온도를 설정합니다.
2. A hand symbol will appear on the display, indicating manual mode.
3. After approximately 5 seconds, the new temperature will be set. The clock display will alternate between the current time and 'Time Left', showing the duration until the next programmed period.
4. This manual setting will automatically cancel when the next programmed period begins.
5. To cancel manual mode before the next program, press the 세트 단추.

7.2. Hold Temperature (Permanent Manual Mode)

To maintain a specific temperature indefinitely:

1. 사용하세요 + or - 버튼을 눌러 원하는 온도를 설정합니다.
2. 를 누르세요 잡고 있다 button. A key symbol will appear on the display.
3. The thermostat will maintain this temperature until you manually cancel it.
4. To cancel the hold function, press the 세트 단추.

7.3. Programming Daily Schedules (P0-P6)

The thermostat allows for 6 programmable periods (P0 to P6) per day. Program P0 is fixed at 00:00 and only its temperature can be adjusted.

1. 를 누르고 계세요 세트 버튼을 누른 후 동시에 음식물 button. The day of the week will start flashing.
2. 사용하세요 + or - buttons to select the day(s) you wish to program (you can select multiple days if they are all flashing).
3. 누르다 음식물. The desired temperature for Program 0 (P0) will flash (time is fixed at 00:00).
4. 사용하세요 + or - buttons to set the desired temperature for P0.
5. 누르다 음식물 to move to Program 1 (P1). The hour for P1 will flash.
6. 사용하세요 + or - buttons to set the desired hour for P1.
7. 누르다 음식물. The temperature for P1 will flash.
8. 사용하세요 + or - buttons to set the desired temperature for P1.
9. Repeat steps 6-8 for Programs P2 through P6.
10. 원하는 프로그램을 모두 설정한 후, 세트 button to save and exit programming mode.

Deleting a Program Interval

To delete a specific program interval (P1-P6), set its time to ' - - : - - ' (which appears when you set the time to 00:00 during programming). Then press 세트 저장하다.

7.4. Copying Programs

To copy program settings from one day to another:

1. 를 누르고 계세요 복사 button for 3 seconds until the day of the week starts flashing.
2. 사용하세요 + or - buttons to select the source day (the day you want to copy from).
3. 누르다 복사. The selected day will stop flashing.
4. 사용하세요 + or - buttons to select the destination day(s) (the day(s) you want to copy to).
5. 누르다 복사 to apply the copy. Repeat for additional destination days if needed.
6. 를 누르세요 세트 button to confirm and save the copied programs.

7.5. Short-Term Program (1-9 Hours)

This function allows you to set a temporary temperature for a specific number of hours (1 to 9).

1. 사용하세요 + or - buttons to set the desired temperature for the short-term period.
2. 를 누르세요 낮 button. A suitcase symbol will appear, and the hour display will flash.
3. 사용하세요 + or - buttons to select the number of hours (1 to 9).
4. Wait for approximately 5 seconds for the setting to save automatically. The clock display will alternate between the current time and 'Time Left', showing the remaining duration.
5. This program will automatically cancel after the set hours, and the thermostat will revert to its regular schedule.
6. To cancel this function manually, press the 세트 단추.

7.6. Holiday Program (1-99 Days)

This function allows you to set a specific temperature for an extended period (1 to 99 days), useful when you are away from home.

1. 사용하세요 + or - buttons to set the desired temperature for your holiday period.
2. 를 누르고 계세요 잡고 있다 button for 3 seconds. Initially, a key symbol will appear, then a suitcase symbol will appear, and the day display will flash.
3. 사용하세요 + or - buttons to select the number of days (1 to 99).
4. Wait for approximately 5 seconds for the setting to save automatically. The clock display will alternate between the current time and 'Time Left', showing the remaining days.
5. This program will automatically cancel after the set days, and the thermostat will revert to its regular schedule.
6. To cancel this function manually, press the 세트 단추.

7.7. HEAT/COOL Mode Selection

The thermostat can operate in either heating or cooling mode.

1. 를 누르고 계세요 세트 버튼을 누른 후 동시에 복사 button. 'HEAT' or 'COOL' will appear on the display.
2. 사용하세요 + or - buttons to switch between 'HEAT' (for heating systems) and 'COOL' (for air conditioning systems).
3. 를 누르세요 세트 선택 사항을 저장하려면 버튼을 클릭하세요.

• In 열 mode: The connected appliance (e.g., boiler) will activate when the room temperature falls below the desired temperature.
• In 시원한 mode: The connected appliance (e.g., air conditioner) will activate when the room temperature rises above the desired temperature.

7.8. 백라이트 설정

그만큼 빛 button controls the display backlight.

• 짧게 누르면 빛 button will illuminate the display for approximately 10 seconds.
• To change the backlight behavior, press and hold the 빛 button for 5 seconds. 'L:ON' or 'L:OF' will appear on the display.
• 사용하세요 + or - buttons to toggle between:
• L:ON: The backlight will illuminate with every button press.
• L:OF: The backlight will only illuminate when the 빛 버튼이 눌렸습니다.
• 누르다 세트 to confirm your selection. Note that 'L:ON' mode will consume batteries faster.

7.9. Switching Sensitivity Adjustment

This setting determines the temperature differential before the heating/cooling system activates or deactivates.

1. 를 누르세요 낮 버튼을 누른 다음 즉시 복사 단추.
2. 사용하세요 + or - buttons to select the desired sensitivity: 'S:1', 'S:2', or 'S:3'.
3. 누르다 세트 확인합니다.

• S:1: Sensitivity of ±0.1°C. For a target of 20°C, heating activates at 19.9°C and deactivates at 20.1°C.
• S:2: Sensitivity of ±0.2°C. For a target of 20°C, heating activates at 19.8°C and deactivates at 20.2°C.
• S:3: Sensitivity of ±0.3°C. For a target of 20°C, heating activates at 19.7°C and deactivates at 20.3°C.

7.10. 온도 교정

You can calibrate the thermostat's temperature reading to match a reference thermometer or to compensate for its location.

1. 를 누르세요 낮 버튼을 누른 다음 즉시 잡고 있다 단추.
2. 사용하세요 + or - buttons to adjust the temperature offset (e.g., -1.0°C to make the thermostat read 1°C lower).
3. 누르다 세트 to confirm. The change will take effect after approximately 10 seconds.

7.11. Pump Protection Function

This function helps prevent damage to your heating system's pump during periods of inactivity.

1. 를 누르세요 낮 버튼을 누른 다음 즉시 음식물 단추.
2. 사용하세요 + or - buttons to select 'HP:ON' or 'HP:OF'.
3. 누르다 세트 확인합니다.

• HP:ON: The pump will automatically run for 1 minute each day, even if no heating is scheduled, to prevent seizing.
• HP:OF: Pump protection is disabled.

7.12. 버튼 잠금

To prevent accidental changes, you can lock the thermostat buttons.

1. To lock the buttons, press the + 그리고 - buttons simultaneously for 5 seconds. A lock symbol will appear.
2. To unlock the buttons, press the + 그리고 - buttons simultaneously for 5 seconds again. The lock symbol will disappear.

8. 유지관리

8.1. 배터리 교체

When the battery low indicator appears on the display, replace the batteries promptly to ensure continuous operation. Refer to section 5.3 for battery installation instructions.

8.2. 청소

온도 조절기의 외부를 부드럽고 마른 천으로 닦으십시오. 연마성 세제, 용제 또는 스프레이를 기기에 직접 사용하지 마십시오.

9. 문제 해결

10. 사양

11. 보증 및 지원

The COMPUTHERM Q7 thermostat comes with a 2년 제조사 보증 구매일로부터. 보증 청구를 위해 구매 증빙을 보관하세요.

For technical support or warranty inquiries, please refer to the contact information provided with your product packaging or visit the official COMPUTHERM web대지.