플루이드마스터 400ACN3P5 변기 급수 밸브 사용 설명서

소개

This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of your Fluidmaster 400ACN3P5 Toilet Fill Valve. Please read these instructions carefully before beginning installation to ensure proper function and longevity of the product.

안전 정보

• Always turn off the water supply to the toilet before beginning any work.
• 설치하는 동안 안전 안경 등 적절한 개인 보호 장비를 착용하세요.
• Do not overtighten nuts or connections, as this may cause damage or leaks.
• 어떤 단계에 대해 확신이 없다면 자격을 갖춘 배관공에게 문의하세요.

패키지 내용

Your Fluidmaster 400ACN3P5 Toilet Fill Valve package typically includes:

• Fluidmaster 400ACN3P5 Toilet Fill Valve
• 리필 튜브
• 리필 클립
• 생크 와셔
• 잠금 너트

그림 1: Packaging for the Fluidmaster 400ACN3P5 Toilet Fill Valve. This image shows a "Three Pack" configuration. Actual package contents may vary based on the specific product variant purchased (e.g., single pack, 5-pack).

설치 방법: 설치 지침

1. 물 공급을 차단하세요: 변기 아래쪽에 있는 급수 밸브를 찾아 물이 완전히 멈출 때까지 시계 방향으로 돌리십시오.
2. 수세식 변기: Flush the toilet to drain most of the water from the tank. Hold the flush handle down to ensure as much water as possible is removed.
3. Remove Remaining Water: 스펀지나 수건을 사용하여 변기 물탱크에 남아있는 물을 모두 닦아내십시오.
4. 전원 공급 라인을 분리하십시오: Disconnect the water supply line from the bottom of the old fill valve. Have a small bucket ready to catch any residual water.
5. 기존 주입 밸브를 제거하십시오. Loosen the lock nut on the underside of the toilet tank that secures the old fill valve. Remove the old fill valve from the tank.
6. 새 주입 밸브를 설치하세요: Insert the new Fluidmaster 400ACN3P5 fill valve into the hole at the bottom of the toilet tank. Ensure the shank washer is properly seated on the outside of the tank.
7. Secure Fill Valve: Hand-tighten the lock nut onto the threaded shank of the new fill valve from the underside of the tank. Do not overtighten.
8. 급수관을 연결하세요: Reconnect the water supply line to the bottom of the new fill valve. Hand-tighten, then use a wrench for a final quarter-turn, being careful not to overtighten.
9. Attach Refill Tube: Attach one end of the refill tube to the small port on the top of the fill valve. Clip the other end of the refill tube to the overflow pipe using the refill clip, ensuring the tube is above the water level in the tank.
10. Adjust Fill Valve Height (if applicable): Some Fluidmaster models allow for height adjustment. If your model has this feature, adjust the height so the critical level mark (C.L.) on the valve is at least 1 inch above the top of the overflow pipe.
11. 물 공급을 켜십시오: Slowly turn the water supply valve counter-clockwise to restore water flow to the toilet tank.
12. 누출 확인: Carefully inspect all connections for any signs of leaks. Tighten connections slightly if necessary.
13. 수위 조절: Allow the tank to fill. The water level should stop approximately 1 inch below the top of the overflow pipe. If adjustment is needed, refer to the specific instructions for your fill valve model (often involves a screw or clip adjustment on the valve itself).

작동 지침

The Fluidmaster 400ACN3P5 Toilet Fill Valve operates automatically. After each flush, the valve senses the drop in water level and opens to refill the toilet tank to the preset level. Once the desired water level is reached, the valve automatically shuts off the water flow. The refill tube ensures that a small amount of water is directed into the toilet bowl during the refill cycle, maintaining the water seal in the bowl.

유지

• 정기 검사: Periodically inspect the fill valve for any signs of wear, cracks, or mineral buildup.
• 청소: If the valve appears to be operating slowly or making unusual noises, mineral deposits may be affecting its performance. Turn off the water supply, remove the cap of the fill valve (refer to specific model instructions for cap removal), and gently clean any visible debris or mineral buildup. Rinse with clean water.
• Check Refill Tube: Ensure the refill tube is securely attached and not kinked or obstructed.

문제 해결

Toilet Runs Continuously

• 수위가 너무 높습니다: Adjust the fill valve to lower the water level in the tank. The water level should be about 1 inch below the top of the overflow pipe.
• Flapper Leak: Check the toilet flapper for proper sealing. A worn or misaligned flapper can cause water to leak into the bowl, making the fill valve run intermittently to refill the tank.
• Refill Tube Too Low: Ensure the refill tube is clipped above the water level in the tank and not inserted directly into the overflow pipe.

Toilet Fills Slowly or Not at All

• Water Supply Off: Ensure the water supply valve to the toilet is fully open.
• Obstructed Inlet: Turn off the water, disconnect the supply line, and check the fill valve's inlet screen for debris. Clean if necessary.
• 미네랄 축적: Follow maintenance steps to clean the fill valve mechanism.

Fill Valve Makes Noise

• 수압: High water pressure can sometimes cause noise. A pressure reducing valve for the whole house might be considered.
• 느슨한 부품: Ensure all connections are secure but not overtightened.
• 미네랄 축적: Clean the valve as described in the maintenance section.

명세서

보증 정보

The Fluidmaster 400ACN3P5 Toilet Fill Valve comes with a 1-year limited warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims. For full warranty details, please refer to the official Fluidmaster web사이트를 방문하거나 고객 지원팀에 문의하세요.

지원하다

For further assistance, technical support, or to inquire about replacement parts, please visit the official Fluidmaster web사이트 또는 고객 서비스 부서에 문의하십시오.

Web대지: www.fluidmaster.com

고객 서비스: Refer to the Fluidmaster web연락처 및 영업시간 안내 사이트입니다.