MSA 5피트 나일론 앵커리지 커넥터 스트랩 사용 설명서

소개

The MSA 5' Nylon Anchorage Connector Strap is designed to provide a temporary and secure anchor point for fall arrest and confined space entry/retrieval systems. Featuring a D-ring on one end and a sewn loop on the other, this strap offers quick and reliable connection. It is constructed from durable nylon and has a minimum breaking strength of 5000 lbs, ensuring robust performance in demanding environments.

Figure 1: The MSA 5' Nylon Anchorage Connector Strap, showing the yellow nylon strap, the metal D-ring, and the sewn loop end. This strap is used to create a temporary anchor point for safety systems.

설정 및 설치

The anchorage connector strap is designed for straightforward installation, primarily in a choker-like manner around a suitable anchor structure. Ensure the anchor point is capable of supporting the anticipated loads and meets all applicable safety standards.

설치 단계:

1. Inspect the Strap: Before each use, thoroughly inspect the entire strap, including the nylon webbing, the D-ring, and the sewn loop. Look for any signs of cuts, abrasions, fraying, excessive wear, heat damage, chemical damage, or deformation of the D-ring. Do not use if any damage is observed.
2. Identify a Suitable Anchor Point: Select an anchor point that is structurally sound and capable of withstanding a minimum load of 5000 lbs (22.2 kN) per attached worker, or as required by local regulations. Examples include structural steel beams, robust piping, or other certified anchorages.
3. Choker Installation:
   • Wrap the nylon strap around the chosen anchor point.
   • Pass the D-ring end through the sewn loop end of the strap.
   • Pull the D-ring end tight to form a secure choker around the anchor point. Ensure the strap is snug and does not slip.
   • Verify that the D-ring is positioned correctly for connection to your fall arrest or retrieval system, allowing for free movement without obstruction.
4. Direct Connection (Alternative): In some applications, the sewn loop may be directly connected to a compatible anchor point, or the D-ring may be connected to a suitable anchor. Always ensure compatibility and proper engagement of all components.
5. 시스템 연결 : Connect your personal fall arrest system (e.g., lanyard, self-retracting lifeline) to the D-ring of the anchorage connector strap. Ensure all connections are secure and properly locked.

중요한 안전 정보: Always consult with a qualified person and adhere to all local, national, and international safety standards and regulations (e.g., OSHA, ANSI) when setting up and using fall protection equipment.

작동 지침

Once properly installed, the MSA Anchorage Connector Strap serves as a reliable anchor point. Its primary function is to provide a secure attachment for personal fall protection equipment.

사용 지침:

• 사용 전 확인: Before each use, confirm that the strap is securely attached to the anchor point and that the D-ring is free from obstruction and properly oriented for connection.
• Connect Fall Protection: Attach your fall arrest lanyard, self-retracting lifeline, or other compatible fall protection component directly to the D-ring of the anchorage strap. Ensure the connector (e.g., carabiner, snap hook) is fully closed and locked.
• 보안 등급 유지: Ensure adequate fall clearance below the work area to prevent contact with lower levels or obstructions in the event of a fall.
• 단일 사용자: This anchorage connector is typically designed for use by one person at a time for fall arrest applications. Refer to specific product labeling or manufacturer's instructions for multi-person use if applicable.
• 날카로운 모서리를 피하세요: Do not allow the strap to come into contact with sharp edges or abrasive surfaces that could damage the webbing. Use edge protectors if necessary.
• 낙상 후 점검: If the anchorage connector strap has been subjected to fall arrest forces, it must be immediately removed from service and destroyed. It is not to be reused after a fall.

유지 관리 및 보관

Proper maintenance and storage are crucial for extending the lifespan and ensuring the continued safety of your MSA Anchorage Connector Strap.

유지:

• 정기 검사: In addition to pre-use checks, conduct a thorough inspection of the strap at least annually, or more frequently depending on usage and environmental conditions, by a competent person. Document all inspections.
• 청소: Clean the strap with a mild soap and water solution. Rinse thoroughly with clean water and allow it to air dry completely in a shaded, well-ventilated area away from direct sunlight or heat. Do not use harsh chemicals, solvents, or bleach.
• 손상: Any strap showing signs of damage, excessive wear, or exposure to chemicals/heat must be immediately removed from service and properly disposed of. Do not attempt to repair damaged equipment.

저장:

• Store the strap in a cool, dry, clean environment, away from direct sunlight, extreme temperatures, corrosive chemicals, and sharp objects.
• Ensure the strap is clean and dry before storage to prevent mildew or degradation.
• Avoid storing the strap in a manner that could cause kinking, twisting, or crushing.

문제 해결

Most issues with the anchorage connector strap can be resolved through proper inspection and adherence to installation guidelines. This section addresses common concerns.

If you encounter issues not listed here, or if you are unsure about the safety of the product, contact MSA customer support or a qualified safety professional.

명세서

보증 정보

Specific warranty terms for the MSA 5' Nylon Anchorage Connector Strap are provided by the manufacturer, MSA. For detailed warranty information, including coverage, duration, and claims procedures, please refer to the documentation included with your product or visit the official MSA web사이트. 보증 청구를 위해 구매 증빙 자료를 보관하세요.

지원 및 연락처

For technical assistance, product inquiries, or safety-related questions regarding your MSA Anchorage Connector Strap, please contact MSA customer support directly.

MSA Official Web대지: www.msasafety.com

참조 website for regional contact information, FAQs, and additional product resources.