1. 서론
This manual provides comprehensive instructions for the installation, operation, and maintenance of the Came RE862 Dual-Channel Surface-Mount Receiver. The RE862 is a versatile radio receiver designed for various applications, including gate and garage door automation systems. It operates at a frequency of 868.35 MHz and features two independent channels, offering flexible control options. Its robust design with IP54 protection allows for outdoor installation.
Please read this manual carefully before proceeding with installation or operation to ensure safe and correct use of the device.
2. 안전 정보
- 전기 안전: Installation and wiring must be performed by qualified personnel in accordance with local electrical codes and regulations. Disconnect power before performing any work on the receiver.
- 전원 공급 장치: Ensure the power supply (12-24V AC/DC) matches the receiver's requirements. Incorrect voltag전자는 장치를 손상시킬 수 있습니다.
- 환경 조건: While the RE862 has an IP54 rating for outdoor use, avoid installing it in locations subject to extreme temperatures, direct water jets, or corrosive substances.
- 간섭: Keep the receiver away from strong electromagnetic fields or other radio frequency devices that could cause interference.
- 용도: Use the receiver only for its intended purpose as a radio control device for automation systems.
3. 패키지 내용
포장을 풀 때 모든 구성 요소가 들어 있고 손상되지 않았는지 확인하세요.
- Came RE862 Dual-Channel Receiver Unit
- 설치 및 배선 지침
- 프로그래밍 가이드
- 설치용 하드웨어(나사, 벽 플러그)
- "Rolling Code Memory" Module (if included, refer to programming guide for use)
Figure 1: Came RE862 Dual-Channel Surface-Mount Receiver. This image shows the compact, black receiver unit, designed for surface mounting.
4. 설정 및 설치
4.1 수신기 장착
- Choose a suitable location for mounting. Due to its IP54 rating, the RE862 can be installed outdoors, but ensure it is protected from direct mechanical impact.
- Mark the drilling points on the wall or surface using the receiver's mounting holes as a template.
- 구멍을 뚫고 적절한 벽면 플러그를 꽂습니다.
- Secure the receiver to the surface using the provided screws.
4.2 배선 연결
The RE862 receiver requires a 12-24V AC or DC power supply. It provides two Normally Open (NO) contact outputs, one for each channel.
- 전원 공급 장치: Connect the 12-24V AC/DC power supply to the designated terminals on the receiver. Observe polarity if using DC power.
- 채널 1 출력: Connect the output terminals for Channel 1 to the control input of your automation system (e.g., gate opener, garage door opener). This is a Normally Open (NO) contact.
- 채널 2 출력: Connect the output terminals for Channel 2 to the control input of your second automation system or function. This is also a Normally Open (NO) contact.
Refer to the detailed wiring diagram included with your product for specific terminal assignments. Ensure all connections are secure and insulated.
5. 사용 설명서
5.1 원격 제어 프로그래밍
The RE862 receiver is designed to work with Came 868.35 MHz remote controls. The programming process typically involves placing the receiver into a learning mode and then transmitting a signal from the remote control.
- 학습 모드로 들어가기: Locate the programming button (often labeled "PROG" or "MEM") on the RE862 receiver. Press and hold this button until an indicator LED (usually red or green) illuminates or flashes, indicating the receiver is in learning mode.
- 원격에서 전송: While the receiver is in learning mode, press the desired button on your Came remote control that you wish to associate with Channel 1. The receiver's LED should change its behavior (e.g., flash rapidly, turn solid, or turn off) to confirm successful learning.
- Repeat for Channel 2 (if applicable): If you wish to program a second button on the remote for Channel 2, repeat the process. Some receivers may require re-entering learning mode for each channel or have a specific sequence for multi-channel programming.
- 학습 모드 종료: The receiver will typically exit learning mode automatically after a short period of inactivity or after a successful programming sequence. Some models may require a short press of the programming button to exit.
For detailed programming steps, including instructions for the "Rolling Code Memory" module if present, refer to the specific programming guide provided with your receiver. The exact procedure may vary slightly depending on the firmware version.
5.2 테스트 작업
After programming, test the remote control's functionality. Press the programmed button on the remote. The receiver's output relay for the corresponding channel should activate, and your connected automation system should respond.
6. 유지관리
- 청소: 수신기 외부는 부드럽고 마른 천으로 정기적으로 청소하십시오. 연마성 세제나 용제는 사용하지 마십시오.
- 점검: Regularly inspect wiring connections for signs of wear, corrosion, or damage. Ensure the housing remains securely mounted and free from cracks.
- 안테나: Ensure the antenna (if external) is unobstructed and in good condition for optimal range.
- 펌웨어 업데이트: Check the Came official website for any available firmware updates, though these typically require specialized tools.
7. 문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 수신기의 전원이 켜지지 않습니다. | 전원 공급이 안되거나 볼륨이 잘못되었습니다tage. | Check power connections and ensure 12-24V AC/DC is supplied. Verify polarity for DC. |
| Remote control does not activate the system. | Remote not programmed, incorrect frequency, or out of range. | Re-program the remote control (Section 5.1). Ensure the remote operates at 868.35 MHz. Check for obstructions and ensure you are within operating range. |
| System activates intermittently. | Interference, weak signal, or loose wiring. | Check for sources of interference. Ensure antenna is clear. Inspect all wiring connections for tightness. |
| "Rolling Code Memory" module not understood. | Lack of specific instructions. | This module typically enhances security by managing rolling codes. Refer to the detailed programming guide for its specific integration and benefits. If no guide is available, contact Came support. |
8. 사양
| 특징 | 세부 사항 |
|---|---|
| 모델 번호 | RE862 |
| 상표 | 왔다 |
| 채널 | 2 |
| 빈도 | 868.35MHz |
| 전원 공급 장치 | 12 - 24V AC/DC |
| 출력 유형 | Normally Open (NO) contact per channel |
| 보호 등급 | IP54(실외 설치에 적합) |
| 연결 기술 | 고주파 |
| 색상 | 검은색 |
9. 보증 및 지원
Came products are manufactured to high-quality standards. For warranty information, please refer to the warranty card included with your purchase or visit the official Came web사이트. 보증 청구를 위해 구매 증빙 자료를 보관하세요.
For technical support, troubleshooting assistance beyond this manual, or to inquire about spare parts, please contact your authorized Came dealer or the official Came customer service department. Contact details can typically be found on the Came web사이트나 제품 설명서에서 확인하세요.
