Gingko Design Cube Alarm Clock Instruction Manual

1. 서론

The Gingko Design Cube Alarm Clock (Model GK08W6) is a digital alarm clock featuring an LED display that can show time, date, and temperature. It incorporates a sound-activated display function for energy saving. This manual provides comprehensive instructions for setting up, operating, and maintaining your device.

패키지 내용:

• Gingko Design Cube Alarm Clock (GK08W6)
• USB 전원 케이블
• 사용 설명서

2. 설정

2.1 장치 전원 공급

The clock can be powered by either 3x AAA batteries (not included) or via the supplied USB cable connected to a USB power adapter (not included) or a computer USB port.

• 배터리 전원: Open the battery compartment on the back of the clock and insert 3x AAA batteries, ensuring correct polarity.
• USB 전원 : Connect the small end of the USB cable to the DC 5V port on the back of the clock and the larger end to a USB power source.

For continuous display, USB power is recommended. Battery power is suitable for portable use or as a backup, but the display will typically turn off after a short period to conserve energy.

이미지 1: 앞면 view of the Gingko Design Cube Alarm Clock displaying the time.

3. 사용 설명서

The control buttons are located on the back of the clock. These typically include 'SET', 'UP', and 'DOWN' buttons.

3.1 시간 및 날짜 설정

1. Press and hold the 'SET' button for 3 seconds to enter time setting mode. The display will flash.
2. Use the 'UP' and 'DOWN' buttons to adjust the hour. Press 'SET' to confirm and move to minutes.
3. Adjust minutes with 'UP'/'DOWN', then press 'SET'.
4. Continue this process to set the year, month, and day.
5. After setting the day, press 'SET' to exit the setting mode.

3.2 알람 설정

The clock supports up to three independent alarms (A1, A2, A3).

1. Press the 'SET' button repeatedly until 'A1' (or A2, A3) appears on the display.
2. Press and hold 'SET' for 3 seconds. The alarm hour will flash.
3. Use 'UP'/'DOWN' to set the alarm hour, then press 'SET'.
4. Use 'UP'/'DOWN' to set the alarm minute, then press 'SET'.
5. The display will show 'ON:A1' or 'OFF:A1'. Use 'UP'/'DOWN' to toggle the alarm on or off. Press 'SET' to confirm.
6. Repeat for A2 and A3 if desired.

3.3 스누즈 기능

When the alarm sounds, press any button (except 'SET' or 'DOWN' during alarm setting) to activate the snooze function. The alarm will sound again after approximately 5 minutes.

3.4 디스플레이 모드

The clock offers various display modes. Press the 'UP' button to cycle through them:

• dp-1: Time, date, and temperature display alternately.
• dp-2: Time display only.

Image 2: The clock displaying the date (month and day).

Image 3: The clock displaying the temperature in Celsius.

3.5 소리 활성화 모드

In sound activation mode, the display will turn off when the room is quiet to save power. It will light up again in response to a sound (e.g., a clap, finger snap, or gentle tap on the clock/surface).

• To activate/deactivate sound activation mode, press the 'DOWN' button.
• When 'ON:SD' is displayed, sound activation is active.
• When '--:SD' is displayed, sound activation is inactive, and the display will remain on (if USB powered).

Image 4: The clock with its display off, indicating sound activation mode is active and the environment is quiet.

4. 유지관리

4.1 청소

To clean the clock, gently wipe the surface with a soft, dry cloth. Avoid using abrasive cleaners, solvents, or excessive moisture, as these can damage the finish or internal components.

4.2 배터리 교체

If using battery power, replace the AAA batteries when the display dims or the clock functions become unreliable. Ensure the clock is powered off or disconnected from USB before replacing batteries. Dispose of old batteries responsibly.

5. 문제 해결

• 화면이 꺼져 있거나 어둡습니다.
  - 배터리 수준을 확인하고 필요한 경우 교체하세요.
  - Ensure USB power cable is securely connected.
  - If in sound activation mode, make a sound to activate the display.
• 시계가 정확한 시간을 유지하지 않음:
  - Re-set the time following the instructions in Section 3.1.
  - Ensure stable power supply (either fresh batteries or consistent USB power).
• 알람이 울리지 않습니다:
  - Verify that the alarm is set to 'ON' (e.g., 'ON:A1') in the alarm settings.
  - Check the alarm time to ensure it is correctly set.
• 버튼이 응답하지 않음:
  - Disconnect power (both USB and batteries) for a few minutes, then reconnect to perform a soft reset.

6. 사양

7. 보증 및 지원

For warranty information and customer support, please refer to the documentation included with your purchase or visit the official Gingko Design web사이트. 보증 청구를 위해 구매 증빙 자료를 보관하세요.

Web대지: www.gingkodesign.com